The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3
http://www.xiaoyu163.com 3 7 63 1515 0 This service manual is intended for qualified service technicians ; it is not meant for the casual do-it- yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
http://www.xiaoyu163.com 3 7 63 1515 0 [Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 ¶ Steps to be taken during repair The steps and care to be taken when Assys are replaced for repair or inspection are described here. First, copy the user setting data to a USB memory device. Before repair, inspection, or downloading of the firmware, the files indicated below must be copied to a USB memory device just in case the user setting data are accidentally reset to default: •...
http://www.xiaoyu163.com 1. SPECIFICATIONS 3 7 63 1515 0 Specifications General Video Input Ω System ............... DVD Player Composite ....BNC x 1, 1.0 Vp-p, 75 (VIDEO IN) Electrical ratings USA and Canada......AC 120 V, 50 Hz/60 Hz Audio Input Ω Europe.......
http://www.xiaoyu163.com 2. EXPLODED VIEWS AND PARTS LIST 3 7 63 1515 0 NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Page 9
http://www.xiaoyu163.com PACKING parts List 3 7 63 1515 0 Mark No. Description Part No. Mark No. Description Part No. Remote Control Unit DXX2574 Mirror Mat (850 x 750) DHL1156 NSP 9 Bettery (R6P, AA) VEM1031 Pad (Top) DHA1704 Label (WEEE) See contrast table (2) Pad (Bottom) DHA1703...
http://www.xiaoyu163.com 2.3 FRONT PANEL SECTION 3 7 63 1515 0 DVDM CN1502 DVDM Solder DVDM CN1501 the No."4" together CN1504 with the No."7". L 13942296513 u163 DVD-V8000 http://www.xiaoyu163.com...
Page 13
http://www.xiaoyu163.com FRONT PANEL SECTION parts List 3 7 63 1515 0 Mark No. Description Part No. KEYB ASSY DWZ1177 PWSB ASSY DWZ1178 FFC (24P) DDD1297 Connector DKN1418 Connector Assy DKP3746 Connector Assy DKP3747 LCD Module DWG1590 Tray Packing C DEC2896 Tray Packing D DEC2897 EMI Sheet A...
http://www.xiaoyu163.com 2.4 LOADER MECHA. ASSY 3 7 63 1515 0 Note : Cleaning paper Refer to Refer to GED-008 "2.5 TRAVERSE MECHA. ASSY-S". " Application of Lubricant". To DVDM CN101 (Pickup Assy-S) To DVDM CN104 (Stepping Motor) Daifree To DVDM CN105 (Spindle Motor) GEM1036 Lubricating Oil GYA1001...
Page 15
http://www.xiaoyu163.com 3 7 63 1515 0 Application of Lubricant Lubricating Oil GYA1001 Around the shaft No. 9 Loading Base Lubricating Oil GYA1001 Lubricating Oil Lubricating Oil No. 11 GYA1001 GYA1001 Lubricating Oil Drive Cam Inner side of a ditch Inner side of a ditch GYA1001 L 13942296513 No.
Page 17
http://www.xiaoyu163.com TRAVERSE MECHA. ASSY-S parts List 3 7 63 1515 0 Mark No. Description Part No. Spindle Motor VXM1112 Stepping Motor VXM1113 Pickup Assy-S OXX8018 Skew Screw VBA1091 Skew Spring VBH1335 Guide Bar VLL1514 Sub Guide Bar VLL1515 Leaf Spring VNC1023 Joint Spring VNC1019...
http://www.xiaoyu163.com 3.3 DVDM ASSY 1/6 [FTS BLOCK] 3 7 63 1515 0 DVDM ASSY (DWS1364) (1/2) Large size SCH diagram L 13942296513 (RF) : RF SIGNAL ROUTE (RF_V) : RF (VIDEO) SIGNAL ROUTE (RF_A) : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : FOCUS SERVO LOOP LINE u163...
Page 23
http://www.xiaoyu163.com 3 7 63 1515 0 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. L 13942296513 1/6, u163 DVD-V8000 http://www.xiaoyu163.com...
Page 24
http://www.xiaoyu163.com 3 7 63 1515 0 DVDM ASSY (DWS1364) (2/2) L 13942296513 Large size SCH diagram u163 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000 http://www.xiaoyu163.com...
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 (AD) (AD) (RF) : RF SIGNAL ROUTE (RF_V) : RF (VIDEO) SIGNAL ROUTE (RF_A) : RF (AUDIO) SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE u163 : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE DVD-V8000 http://www.xiaoyu163.com...
Page 31
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 (VD) (AD) (RF_V) : RF (VIDEO) SIGNAL ROUTE (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE u163 DVD-V8000 http://www.xiaoyu163.com...
Page 33
http://www.xiaoyu163.com 3 7 63 1515 0 (AD) (VD) (VD) L 13942296513 (RF_V) : RF (VIDEO) SIGNAL ROUTE u163 (VD) : VIDEO DATA SIGNAL ROUTE (AD) : AUDIO DATA SIGNAL ROUTE : AUDIO (DIGITAL) SIGNAL ROUTE DVD-V8000 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3.6 DVDM ASSY 4/6 [VIDEO BLOCK] 3 7 63 1515 0 DVDM ASSY (DWS1364) (1/2) (VD) : VIDEO DATA SIGNAL ROUTE : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE Large size : Y SIGNAL ROUTE SCH diagram (Cb) : Cb SIGNAL ROUTE...
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 DVDM ASSY (DWS1364) (2/2) (VD) : VIDEO DATA SIGNAL ROUTE : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (VD) (Cr) : Cr SIGNAL ROUTE (VD)
http://www.xiaoyu163.com 3.9 VJKB and USBB ASSYS 3 7 63 1515 0 VJKB ASSY (DWZ1175) (1/2) CN901 Large size SCH diagram CN1201 L 13942296513 : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (Cr)
Page 46
http://www.xiaoyu163.com 3 7 63 1515 0 VJKB ASSY (DWZ1175) (2/2) : V SIGNAL ROUTE (S_Y) : S_Y SIGNAL ROUTE (S_C) : S_C SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE (Ex_V) : Ex_VIDEO SIGNAL ROUTE L 13942296513 Large size SCH diagram...
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3.10 AJKB ASSY 3 7 63 1515 0 AJKB ASSY (DWZ1176) (1/2) CN551 Large size SCH diagram L 13942296513 : AUDIO (DIGITAL) SIGNAL ROUTE (L/R) : AUDIO (ANALOG) SIGNAL ROUTE (ExL/ExR) : Ex_AUDIO SIGNAL ROUTE u163 DVD-V8000 http://www.xiaoyu163.com...
Page 49
http://www.xiaoyu163.com 3 7 63 1515 0 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. CN1503 L 13942296513 u163 DVD-V8000 http://www.xiaoyu163.com...
Page 50
http://www.xiaoyu163.com 3 7 63 1515 0 : AUDIO (DIGITAL) SIGNAL ROUTE AJKB ASSY (L/R) : AUDIO (ANALOG) SIGNAL ROUTE (DWZ1176) (2/2) (ExL/ExR) : Ex_AUDIO SIGNAL ROUTE L 13942296513 Large size SCH diagram u163 NOTE: DVD-V8000 http://www.xiaoyu163.com...
Page 51
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram and PCB diagram. DVD-V8000 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3.12 SYPS ASSY 3 7 63 1515 0 SYPS ASSY (DWR1401) [Figure of reference] • This assembly has no service part. • Please exchange assembly. LIVE NEUTRAL L 13942296513 u163 DVD-V8000 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 3.13 WAVEFORMS 3 7 63 1515 0 DVDM ASSY Note: The numbers for the waveform photos (circled) are identical to those for the schematic diagrams, PCB diagrams, and troubleshooting flowcharts. IC101-pin3 (RFP) IC201-pin1 (EFMOUT) IC701-pin142 (RERR) CN901-pin26 (Cb) [INTERLACE] V:200 mV/div.
Page 57
http://www.xiaoyu163.com 3 7 63 1515 0 DVDM ASSY VJKB ASSY AJKB ASSY Note: The numbers for the waveform photos (circled) are identical to those for the schematic diagrams, PCB diagrams, and troubleshooting flowcharts. DC MODE DC MODE CN551-pin9 (PCMCLK) IC7201-pin2 (MO1) IC8101-pin7 (VOUTL) DC MODE V:500 mV/div.
http://www.xiaoyu163.com 4. PCB CONNECTION DIAGRAM 4.1 LOAB ASSY 3 7 63 1515 0 NOTE FOR PCB DIAGRAMS : 1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for diagrams.
http://www.xiaoyu163.com 4.6 SYPS ASSY 3 7 63 1515 0 SIDE A SIDE B SYPS ASSY [DWR1401] AC INLET ASSY L 13942296513 CN101 CN101 u163 CN401 DVD-V8000 http://www.xiaoyu163.com...
http://www.xiaoyu163.com 5. PCB PARTS LIST 3 7 63 1515 0 NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
http://www.xiaoyu163.com 6.3 NECESSARY ADJUSTMENT POINTS 3 7 63 1515 0 When Adjustment Points Exchange Parts of Mechanism Assy ∗ After adjustment, screw locks Mechanical ~, Ÿ, ! Exchange the Pickup point with the Screw tight. Electric point Mechanical Exchange the Traverse Mechanism point Electric point...
http://www.xiaoyu163.com 6.4 TEST MODE 3 7 63 1515 0 TEST MODE: ON TEST POWER GGF1381 Test mode remote control unit TEST MODE: DISC SET CHECK <TRAY OPEN> DVD, CD DVD disc REP • A REP • A &&& DSC - TEST MODE: PLAY L 13942296513 <PLAY>...
http://www.xiaoyu163.com 6.5 MECHANISM ADJUSTMENT 3 7 63 1515 0 Tangential and Radial Height Coarse Adjustment START Cautions: • Remove the Loading Mecha. Assy. Keep spacer for future use. • Remove a Spacer for height adjustment (used only for 2003 models) attached to the back side (shaded area) of the Loading Mecha.
Page 85
http://www.xiaoyu163.com 3 7 63 1515 0 DVD Jitter Adjustment • Playback method of inner and outer address for the purpose is refererd to "6.4 TEST MODE". • Jitter indication of the monitor is refererd to "7.1.2 TEST MODE SPECIFICATIONS". Use disc: GGV1025 START Traverse •...
http://www.xiaoyu163.com 6.6 ELECTRICAL ADJUSTMENT 3 7 63 1515 0 Note: If adjustments of the Traverse mechanism are inappropriate: • The magnitude of jitter and the error rate increase. • The playability of a disc is deteriorated. • In some cases, block noise may appear. Measuring and Adjustment Points SIDE A DVDM ASSY...
http://www.xiaoyu163.com 7. GENERAL INFORMATION 3 7 63 1515 0 7.1 DIAGNOSIS 7.1.1 SELF-DIAGNOSIS FUNCTION OF PICKUP DEFECTIVE This unit can confirm the laser diode current value (DVD: 650 nm, CD: 780 nm) of pickup on the Test Mode screen. (Press the ESC → TEST keys in order on the test mode remote control unit (GGF1381) to enter the test mode.) It's effective in case of the following condition.
http://www.xiaoyu163.com 7.1.2 TEST MODE SPECIFICATIONS 3 7 63 1515 0 Display Specification of the Test Mode Character in bold : Item name : Information display 13 14 19 20 - Jitter value [J – ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗] 1 Address indication The address being traced is displayed in number.
Page 89
http://www.xiaoyu163.com Test Mode Functional Specification 3 7 63 1515 0 1 Test mode entry In the power ON state, press the [ESC] (A8-5F) key and [TEST] (A8-5E) key in order of the Test mode remote control unit. • Light the LCD and all LEDs, and goes out the LCD and LEDs when pressing the keys of something. •...
http://www.xiaoyu163.com 7.1.3 SELF-DIAGNOSIS FUNCTION 3 7 63 1515 0 SELF-DIAGNOSIS Two types of self-diagnosis are provided with this unit: (1) Self-diagnosis that is performed each time the power is turned on (2) Self-diagnosis upon request, activated using the remote control unit 1.
Page 91
http://www.xiaoyu163.com In a case of an error for Item 6 In a case of an error for Item 0 3 7 63 1515 0 AV DECODER T-REX REG. ACCESS NG ACCESS NG In a case of an error for Item 7 In a case of an error for Item - AV DECODER SYSCON SRAM...
http://www.xiaoyu163.com 7.1.4 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE 3 7 63 1515 0 • LCD indication of EDC / ID error (short cut function) Indicate it in LCD with the "ESC"+"CX" keys (LD remote control unit). Indication is released with the "ESC" key during display. LCD indication contents 0 0 / 0 0 / 0 1 ∗...
http://www.xiaoyu163.com 7.1.5 ERROR DISPLAY 3 7 63 1515 0 Error codes that are displayed on the LCD display without using the remote control unit LCD Display Possible causes Operation of the unit The sound may not out with AV1 VER AV-1 chip is not a match with the program of system controller the specific audio.
Page 94
http://www.xiaoyu163.com 3 7 63 1515 0 Description of Causes if with a DVD Causes if with a CD Operation of the Unit Error 39 SGC converge SGC could not converge during detects the peak Open timeout The unit did not enter Stop mode within 10 seconds of issuance of a Stop command. 41 Spindle timeout Stop Disc distinction is not completed even if passes for 10 seconds after the spindle turned.
Page 95
http://www.xiaoyu163.com Description of 3 7 63 1515 0 Causes if with a DVD Causes if with a CD Operation of the Unit Error Subcode check Subcode could not be read within 1 Open (Subcode readout second after the tracking on. failure during startup failure) A command could not be issued to DSP because...
http://www.xiaoyu163.com 7.1.6 ERROR HISTORY 3 7 63 1515 0 How to display the error history Use the dedicated remote control unit for service. Press the ESC then CHP/TIM keys. The measured error rate value, results of self-diagnosis, and time data read from the real-time clock are displayed on the screen, as shown below: Press the CHP/TIM key again to display the detailed information of the error history and results of self-diagnosis.
Page 97
http://www.xiaoyu163.com How to clear data of the error history 3 7 63 1515 0 The data of the error history can be cleared by issuing the "EE0016EC" RS-232C command. How to copy data of the error history to a USB memory device The data of the error history can be copied to a USB memory device, using SAVE ERROR LOG in the ADV.SETUP menu.
http://www.xiaoyu163.com 7.1.7 ACCUMULATED POWER-ON TIME AND PLAYBACK TIME 3 7 63 1515 0 Displaying the accumulated power-on time and playback time The accumulated power-on time and playback time are displayed on the screen and the LCD when the POWER key on the main unit is pressed while the DISPLAY key is held pressed.
http://www.xiaoyu163.com 7.1.8 TROUBLE SHOOTING 3 7 63 1515 0 START Power ON • Remote control unit or IR signal line damaged. (When key input of the remote control unit is not completed) • Blow out fuse of the primary side •...
Page 100
http://www.xiaoyu163.com 3 7 63 1515 0 • Check the following connections and FTS drive IC (IC351) : DVDM Assy CN114 (4P flexible cable) Carriage does not move. Check the Stepping motor signals, IC351-pin 31, 32, 34, 35 and IC601-pin 47, 48. (Stepping positioning) •...
http://www.xiaoyu163.com 7.1.9 POWER ON SEQUENCE 3 7 63 1515 0 Sequences after power is on Power ON Flash check An error indication is displayed on the LCD. If the indication is "FLASH SUM" or "FLASH ID," connect the dedicated cable for downloading to the 15-pin D-SUB connector and download the firmware.
Page 102
http://www.xiaoyu163.com 3 7 63 1515 0 Is it a start time programmed by the timer? Set the address of the target. Is the Power-on-Start setting made? Set the address of the target. Tray open? : If there is a problem in closing of the tray, Tray close an error indication is displayed on the LCD.
Does the monitor support HDCP? Check if there is any problem with the initialization processes, including HDCP initialization. (Connect a Pioneer plasma Purpose: display that is equipped with the HDMI input for checking. To check if there is any problem with the HDMI output line The HDMI-DVI conversion cable is required for the connection.)
http://www.xiaoyu163.com 7.2 UPGRADING 7.2.1 UPGRADING OF THE FIRMWARE 3 7 63 1515 0 Upgrading of the firmware is performed, using the CD-R for upgrading. 1 Install the CD-R for upgrading in the tray and press the STOP/OPEN/CLOSE key on the main unit or the OPEN/CLOSE key on the remote control unit.
http://www.xiaoyu163.com 7.2.2 IF UPGRADING OF THE FIRMWARE FAILS 3 7 63 1515 0 SERIAL DOWNLOAD [Purposes] If upgrading of the firmware (using the CD-R) fails, upgrading via the serial port is required. This method of upgrading is explained here. [Tools to be used] [Connection] Connect as follows: •...
http://www.xiaoyu163.com 7.3 SETTING THE DESTINATION 3 7 63 1515 0 In conventional models, as many number of sub-microcomputer units as that of destinations were designed, because a port set for each destination was provided with a sub-microcomputer unit. However, with this model, the sub-microcomputer unit is common to all destinations.
http://www.xiaoyu163.com 7.4 SETTING THE ID NUMBER AND COPYING THE ID DATA 3 7 63 1515 0 The ID number is stored in the flash memory on the DVDM Assy and the EEPROM on the AJKB Assy. The ID data are stored in the EEPROM on the AJKB Assy.
http://www.xiaoyu163.com 7.5 SERIAL NUMBER SETTING 3 7 63 1515 0 The serial number of this unit is stored in the EEPROM on the AJKB Assy. When the AJKB Assy is replaced, serial number setting is also required. The remote control unit for service is used for setting. How to set Press ESC then the 9 key to enter Serial Number Setting mode.
http://www.xiaoyu163.com 7.6 DISASSEMBLY 3 7 63 1515 0 Note 1: Do NOT look directly into the pickup lens. The laser beam may cause eye injury. Note 2: Even if the unit shown in the photos and illustrations in this manual may differ from your product, the procedures described here are common.
Page 110
http://www.xiaoyu163.com 3 7 63 1515 0 Front Panel Section Disconnect the one flexible cable. Disconnect the two connectors. Remove the one screw. Unhook the five hooks. 1 2 2 CN1502 CN1504 CN1501 DVDM Assy L 13942296513 Bottom view Remove the front panel section. Front panel section u163 DVD-V8000...
Page 111
http://www.xiaoyu163.com 3 7 63 1515 0 AJKB Assy Remove the three screws. Remove the two screws. Remove the two hex. screws. Remove the two hex. screws. Rear view Remove the one screw. AJKB Assy Remove the PCB spacer. Remove the AJKB Assy. DVDM Assy Remove the one screw.
Page 112
http://www.xiaoyu163.com 3 7 63 1515 0 Diagnosis Connect the jig flexible cable 24P and extension board. Insulation AJKB Assy Insert the two insulation sheet. sheet DVDM Assy Arrange the unit as shown in the photo. Insulation sheet Diagnosis CN1504 CN1501 CN1502 Extension board (GGF1575)
Page 113
http://www.xiaoyu163.com 3 7 63 1515 0 LOADER MECHA. Assy LOADER MECHA. Assy Note: For clarity, the front panel section was removed for the photo, but the actual work can be done without removing it. Remove the five screws. Remove the mecha. case (top). Mecha.
Page 114
http://www.xiaoyu163.com 3 7 63 1515 0 Disconnect the three flexible cables, and the one connector. CN103 CN115 CN114 CN111 DVDM Assy L 13942296513 Remove the four screws. Remove the LOADER MECHA. Assy. LOADER MECHA. Assy u163 DVD-V8000 http://www.xiaoyu163.com...
Page 115
http://www.xiaoyu163.com 3 7 63 1515 0 Bridge and Tray Remove the one screw. Remove the bridge. Pull out the tray, then remove it by pressing the hook. Hook Bridge Tray Note when reinserting the tray Drive cam When reinserting the tray, first align the triangle printed on the loading base and the pin of the drive cam, then L 13942296513 insert the tray.
Page 116
http://www.xiaoyu163.com Traverse Mecha. Assy-S 3 7 63 1515 0 Flexible cable Dislodge the flexible cables from their factory for the spindle motor Front side placement. Flexible cable Flexible cable Bottom view for the pickup for the stepping motor L 13942296513 Cleaning paper GED-008 Cleaning liquid...
Page 117
http://www.xiaoyu163.com Pickup Assy-S 3 7 63 1515 0 Front side Note: The Pickup Assy-S can be removed without removing the Traverse Mecha. Assy-S. (shown as Step π.) Dislodge the flexible cable for the pickup from its packaged placement. Remove the flexible cable for the pickup. Flexible cable for the pickup Bottom view L 13942296513...
Page 118
http://www.xiaoyu163.com Remove the two screws. 3 7 63 1515 0 Pickup Assy-S Note: The screws are secured with the silicone adhesive. Make sure to apply the silicone adhesive after reattaching the screws. Leaf spring Joint spring Silicone adhesive GEM1037 Joint 03 Silicone adhesive GEM1037 Arrangement of the flexible cable...
Page 119
http://www.xiaoyu163.com 3 7 63 1515 0 Arrangement of the flexible cable (use a 24P flexible cable: VDA2135) for the pickup : Conductive surface Note: Be sure to move the Pickup Assy-S to the innermost perimeter. Pass the flexible cable below the hook, and fold it back. Fold the flexible cable inward at the position of the reference line.
http://www.xiaoyu163.com 7.7 PIN FUNCTION OF THE PCB ASSY 3 7 63 1515 0 Internal Connection (1) CN7001 (VKN1433): VJKB Assy → CN901 (VKN1433): DVDM Assy No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function − LETTER 0 V: OFF, 3.3 V: ON V.ENCout Cr SQEEZE 0 V: OFF, 3.3 V: ON...
Page 121
http://www.xiaoyu163.com 3 7 63 1515 0 (3) CN8701 (VKN1814): AJKB Assy → CN1503 (VKN1510): DVDM Assy No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function V+3E EVER+3.3 V SEL_RS H: D-SUB 15 pin, L: D-SUB 9 pin RTC_CS Chip select signal for RTC POWER_IN...
Page 122
http://www.xiaoyu163.com 3 7 63 1515 0 External Connection (1) JA7501 (DKN1267): VJKB Assy → Video output products No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function − Ext In Video Composite Video in: 1 Vp-p GNDA (2) JA7502 (VKB1122): VJKB Assy → Composite Video Monitor No.
Page 123
http://www.xiaoyu163.com 3 7 63 1515 0 (9) JA8701 (DKN1400): AJKB Assy → Black Burst signal generator No. I/O Pin Name Pin Function No. I/O Pin Name Pin Function Ext_sync IN1 Ext-sync (Black burst) Ext_sync IN2 Ext-sync (Black burst) − − GNDD GNDD (10) CN8702 (DKN1435): AJKB Assy →...
Page 124
http://www.xiaoyu163.com 3 7 63 1515 0 Internal Connection and Pin Function of the DVDM Assy (DWS1364) • Block Diagram IC781 IC902 16M IC741 16M SDRAM SDRAM SDRA M 16ME BY PD0- PD7 Q602 PB0- PB9 LD(650) PC0- PC9 IC701 BCKA0 IC751 LD(780) IC901...
Page 125
http://www.xiaoyu163.com 3 7 63 1515 0 Pin (Signal) Function of the DVDM Assy (DWS1364) (1) CN401 (AKM1284) For power supply input No. Pin Name Pin Function No. Pin Name Pin Function − − EV6V(B) +6 V power supply Ground − −...
Page 126
http://www.xiaoyu163.com 3 7 63 1515 0 (5) CN111 (VKN2045) For pickup connection No. Pin Name Pin Function No. Pin Name Pin Function − GNDD Ground VRCOM Monitoring voltage − +5 V power supply VR780 Monitor diode VR for CD − PU-B3 input GNDD Ground...
Page 127
http://www.xiaoyu163.com 3 7 63 1515 0 (9) CN1201 (AKM1283) For USBB Assy connection No. Pin Name Pin Function No. Pin Name Pin Function − − GNDD Ground +5V_U2 CH2 +5 V supply line − − V+3A +3 V power supply +5V_U2 CH2 +5 V supply line −...
Page 128
http://www.xiaoyu163.com 3 7 63 1515 0 (13) CN551 (VKN1510) For AJKB Assy connection (audio) No. Pin Name Pin Function No. Pin Name Pin Function XAMUTE Audio mute signal Audio DAC mode clock signal − ASEL Audio select signal Ground LRCK L/R clock signal Audio DAC mode data signal −...
Page 129
http://www.xiaoyu163.com 3 7 63 1515 0 The selecting signal logic of the principal switch section ¶ Clock generator input frequency ¶ Monitor output switch Sampling Input of Clock Generator Monitor Output 44.1 KHz External monitor 44 x 48 VSEL1 48 KHz ¶...
http://www.xiaoyu163.com 7.8 PARTS 7.8.1 IC 3 7 63 1515 0 ¥ The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams. List of IC LA9704WS1, PD6345A, PE5286B, M65776BFP, PD0280B, CD0040AF, SII9190CTG64, UHC124BF, PE5557B, LC78652W LA9704WS1 (DVDM ASSY: IC101) •...
Page 131
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions TESI TES comparator input TES output Deffect detection BHMIX PH, BH, wobble switching output BHACI BH–AC input RF bottom detection output RF peak detection output Capacitor connection terminal for DC cut ISET Resistor connection terminal for BPF center frequency setting BCAI...
Page 132
http://www.xiaoyu163.com 3 7 63 1515 0 PD6345A (DVDM ASSY: IC601) • FR Pin Function Pin Name Pin Functions I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus I/O Data bus...
Page 133
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions LODRV D/A Loading, motor drive SEL_TV A/D NTSC/PAL/AUTO switching signal A/D Not used A/D Not used XOEM A/D OEM model protection input LDREAD A/D Input for LD current value indication A/D Not used A/D Not used LODPOS...
Page 134
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions LOAD_ON FLASH MEMORY write protect release − 100 GND Ground 101 XPROURST VIDEO reset signal 102 VOFF VIDEO amplifier mute signal 103 HDMIRST Reset signal of HDMI CONT 104 SY_SEL External sync.
Page 135
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions 149 XCSFLSH Chip select output to Flash ROM 150 XCSAV1 Chip select of the AV-1 CHIP 151 XCSEBY Chip select of the EBY Chip 152 XCS3 Chip select of the servo DSP 153 XCSSRAM Chip select of the 4M SRAM −...
Page 136
http://www.xiaoyu163.com 3 7 63 1515 0 PE5286B (DVDM ASSY: IC701) • EBY-Chip IC Pin Function Pin Name Pin Function − Ground − Ground − VDD3.3 Power supply (+ 3.3 V) DMCK System clock of the DVD/CD-ROM decoder DMACKI 33 MHz input BUNRI GND fixed −...
Page 137
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − VDD3.3 Power supply (+ 3.3 V) − Ground − Not used − VDD2.5 Power supply (+ 2.5 V) − VDD3.3 Power supply (+ 3.3 V) Data bus 6 for DRAM Data bus 5 for DRAM Data bus 4 for DRAM Data bus 3 for DRAM...
Page 138
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − 103 VDD3.3 Power supply (+ 3.3 V) − 104 VDD2.5 Power supply (+ 2.5 V) − 105 GND Ground − 106 GND Ground − 107 VDD3.3 Power supply (+ 3.3 V) 108 SAD3 Data bus D11 −...
Page 139
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − 156 GND Ground − 157 VDD2.5 Power supply (+ 2.5 V) − 158 VDD3.3 Power supply (+ 3.3 V) 159 ATC Output a direct current error of a RF signal as a PWD pulse 160 ASC Output frequency error of a sync period as a PWD pulse 161 XRESET...
Page 140
http://www.xiaoyu163.com 3 7 63 1515 0 M65776BFP (DVDM ASSY: IC751) • AV-1 IC Pin Function Pin Name Pin Function − Ground BCLK Strobe signal of BD pin BDEN Ground fixed BDREQ Data request signal BSECH Ground fixed I/O Data bus I/O Data bus I/O Data bus I/O Data bus...
Page 141
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − Ground XDREQ 1 DMA request signal for OSD bit map transfer XDACK10 DMA acknowledge signal for OSD bit map transfer Address bus 3 for SDRAM Address bus 4 for SDRAM Address bus 2 for SDRAM −...
Page 142
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − 103 VDD18 Power supply (+ 1.8 V) − 104 VDD33 Power supply (+ 3.3 V) − 105 CLKO Not Used 106 27MAV1 System clock input (27 MHz) − 107 AVDD18 Analog power supply (+ 1.8 V) −...
Page 143
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function − 156 VDD33 Power supply (+ 3.3 V) 157 PDR[8] Not Used 158 PDR[9] Not Used 159 LRCLK Clock for channel distinction (L/R) of PCM audio data 160 CDLRCK L/R clock which is input from CDDSP 161 CDBCK PCM bit clock which is input from CDDSP 162 CDDATA...
Page 144
http://www.xiaoyu163.com 3 7 63 1515 0 PD0280B (DVDM ASSY: IC1001) • T-REX IC Pin Function Pin Name Pin Functions − Digital ground XTCK1 Test exclusive use input pin Test exclusive use input pin XTST Test exclusive use input pin Test exclusive use input pin SMCK Test exclusive use input pin Color signal input...
Page 145
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions I/O I2C data I/O I2C clock input − Digital ground NRST System reset input TEST0 Test exclusive use input pin (Connect to ground) TEST1 Test exclusive use input pin (Connect to ground) TEST2 Test exclusive use input pin (Connect to ground) TEST3...
Page 146
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions QCLK Video clock output − 100 VDDI VDD for Core (+ 2.5 V) − 101 VSS Digital ground 102 EXCLK Video clock input in external PLL use − 103 OVDDE3 VDD for I/O (+ 3.3 V) 104 PH1 Signal output 1 for external PLL comparator...
Page 147
http://www.xiaoyu163.com 3 7 63 1515 0 CD0040AF (DVDM ASSY: IC901) • PRO-U (Video Encoder) IC Pin Function Pin Name Pin Functions − OVDD VDD for I/O (+ 3.3 V) CLKI 27 MHz clock input TEST7 Test input (connect to ground) PLL_EN PLL enable input I/O ITU-R BT.656/601 input...
Page 148
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) ANSI/SMPTE293M output (Y) − OVDD VDD for I/O (+ 3.3 V) − CVSS Digital ground for core − OVSS Digital ground for I/O ANSI/SMPTE293M output (Cb/Cr) ANSI/SMPTE293M output (Cb/Cr) ANSI/SMPTE293M output (Cb/Cr)
Page 149
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions − OVSS Digital ground for I/O 100 RAS Command output of SDRAM Row Address Strobe 101 DQM SDRAM DQM output 102 CAS Command output of SDRAM Column Address Strobe 103 MCLK SDRAM clock output (54 MHz) 104 WE SDRAM Write Enable output...
Page 150
http://www.xiaoyu163.com 3 7 63 1515 0 SII9190CTG64 (DVDM ASSY: IC1051) • HDMI Transmitter IC Pin Function Pin Name Pin Functions − Digital VCC (+ 3.3 V) 12 bit input pixel data bus 12 bit input pixel data bus Data enable HSYNC Horizontal sync input control signal VSYNC...
Page 151
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions 12 bit input pixel data bus 12 bit input pixel data bus − Digital ground − Digital VCC (+ 3.3 V) 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus 12 bit input pixel data bus...
Page 152
http://www.xiaoyu163.com 3 7 63 1515 0 UHC124BF (DVDM ASSY: IC1201) • USB Driver IC Pin Function Pin Name Pin Functions − 3.3 V power supply Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus Address bus...
Page 153
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions I/O Data bus I/O Data bus − 3.3 V power supply − Ground I/O Data bus I/O Data bus I/O Data bus I/O Data bus XRESET Master reset Memory write strobe Memory read strobe TMS0 Not used...
Page 154
http://www.xiaoyu163.com 3 7 63 1515 0 PE5557B (DVDM ASSY: IC1501) • LCD Control IC Pin Function Pin Name Pin Functions KEY_OUT2 Key matrix output KEY_OUT3 Key matrix output KEY_OUT4 Key matrix output − AVSS Analog ground LCD_VR LCD display density adjustment −...
Page 155
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Functions POWER_LED POWER key LED lighting signal KEYLOCK_LED Key lock LED lighting signal PLAY_LED Play LED lighting signal JAMMAA JAMMAER input JAMMAB JAMMAER input JAMMAC JAMMAER input JAMMAD JAMMAER input JAMMAE JAMMAER input JAMMAX JAMMAER input...
Page 156
http://www.xiaoyu163.com 3 7 63 1515 0 LC78652W (DVDM ASSY: IC201) • Servo DSP IC Pin Function Pin Name Pin Function EFMOUT Status output after binarization of EMF C2 flag output ROMXA CD-ROM data output ROMCK Shift clock output for CD-ROM data output LRSY L/R clock output for CD-ROM data output XHSMOVE...
Page 157
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Pin Function TEST4 Test input pin Mirror detection signal I/O − JT/XRR Not used DEFIN Defect signal control DEFOUT LDD monitor output FG counter input CTRF Status input after binarization of EMF RESB Reset input Chip select input...
http://www.xiaoyu163.com 7.9 DISC / CONTENT FORMAT PLAYBACK COMPATIBILITY 3 7 63 1515 0 Disc / Content Format Playback Compatibility General disc compatibility Personal computer-created disc compatibility This player was designed and engineered to be compatible with software bearing one or more of the following logos: •...
http://www.xiaoyu163.com 8. PANEL FACILITIES 3 7 63 1515 0 Controls and Displays Front panel 14 15 17 18 19 20 21 22 23 5 6 7 8 9 10 11 1 STANDBY/ON button ( VIDEO: When the button is pressed so that the indicator lights, video Press to turn the player ON or set to standby mode.
http://www.xiaoyu163.com 3 7 63 1515 0 Rear panel 1 Power cord connector (AC IN) Important 2 Extend Terminal connector (EXT TERMINAL) • The DVD-V8000 is provided with video and audio input External switches can be connected to control the DVD-V8000. connectors, and supports the use of 1 Vp-p composite The connector can also be used as an RS-232C interface.
http://www.xiaoyu163.com 3 7 63 1515 0 Remote control unit 9 REV SCAN button ( Press for fast reverse scanning. Scanning speed will change in 3 levels each time the button is pressed. 10 PLAY button ( ) Press to start playback. 11 PAUSE button ( ) During playback, press to pause playback of video/audio.
http://www.xiaoyu163.com 3 7 63 1515 0 Operation using a mouse 29 REV STILL/STEP button ( During playback, press to pause playback and display still In addition to the remote control unit, a mouse can also be image; Press and hold for reverse slow-motion playback. Press used to operate the DVD-V8000 if desired.
http://www.xiaoyu163.com 9.2 INSTALLATION PROCEDURES 3 7 63 1515 0 Installation Procedures 3. After confirming that the screws installed in step 1. Disconnect all cords and cables (including power 2 are tightened securely, install the player on the cord) attached to the player. rack.
http://www.xiaoyu163.com 3 7 63 1515 0 7 Jigs list Name Jig No. Remarks Service Remote Control Unit GGF1381 adjustment, diagnosis DVD Data Disc GGV1174 diagnosis (ID data setting) 24P Flexible Cable GGD1111 Diagnosis of DVDM Assy Extension Board GGF1575 Diagnosis of DVDM Assy DVD Test Disc (DVD-Video) GGV1025 Check of DVD-Video...
Need help?
Do you have a question about the CB-A802 and is the answer not in the manual?
Questions and answers