TE2.1E AA EN 2 1. Technical Specifications, Connections and Chassis Overview • Reception 100 programmes, PLL Tuning, Aerial Input : 75 Ohm • TV Systems Off Air PAL B/G + D/K + SECAM B/G + D/K, SECAM L/L’ • Add Systems Ext In NTSC 3.58 + NTSC 4.43...
Page 3
TE2.1E AA EN 3 Connections 1.1.1 Rear Connections EXT-2 EXT-1 EuroScart 1. Audio Output 1. right channel 0.5 VRMS/<1k0 2. Audio Input 1. right channel 0.5 VRMS/>10k0 3. Audio Output 2. left channel 0.5 VRMS/<1k0 4. GND (audio) 5. GND 6.
TE2.1E AA EN 4 2. Safety Instructions, Warnings and Notes 2.1 General 1. Use only the original spare parts with the same specifications for replacement. 2. Only the original fuse value should be used. 3. Safety components, indicated by the symbol, should be replaced by components identical to the original ones.
TE2.1E AA EN 6 4. Mechanical Intructions Disassembly procedure is explained as below. Before disassembling the TV set please read the safety instructions and warning parts of the service manual. • Turn off TV and plug the mains out • Remove screws (10 pieces) to dismount the back cover •...
TE2.1E AA EN 7 5. Service Modes, Error Codes and Fault finding 5.1 Menu Structure General Menu Options To minimise the number of keys on the remote control unit, less frequently used functions are accessible only via simple menus. The menus are controlled by the following keys;...
Page 8
TE2.1E AA EN 8 5.2 Menu Control Main Menu Picture Sound Features Installation Picture Menu Brightness 64 Steps Colour 64 Steps Contrast 64 Steps Sharpness 64 Steps 64 Steps (for NTSC only) Colour Temp : Normal, Warm, Cool Store Stored...
Page 9
…, A (Austria), B (Belgium), CH (Switzerland), D (Germany), DK (Denmark), E (Spain), F (France), FI (Finland), GB (UK), GR (Greece), I (Italy), N (Norway), NL (Netherlands), P (Portugal), IRL (Ireland), L (Luxemburg), S (Sweden), TR (Turkey) Philips 28” 4:3 FS Austria Belgium...
Page 10
TE2.1E AA EN 10 5.4 Fault finding diagram of Power supply Fuse DP01 - 04 FP01 CP01 - 04 Defective CP06, TP01 Switched mode Power Supply defective, +145V is missing or level is wrong RP07, RP05 Voltage open and drain of...
TE2.1E AA EN 29 8. Alignments Note: SERVICE MODE IS ACTIVED BY PRESSING VOLUME – ON LOCAL KEYBOARD AND TIMER BUTTON ON RC AT THE SAME TIME This software provides menu flexibility and full control to software. Service persons can adjust the TV in all manners.
Page 30
TE2.1E AA EN 30 EXP-VA: This is geometry adjustment variable based on vertical changes of 4:3 EXPAND mode amplitude. EW, PW: These are all geometry adjustment variables based on horizontal changes of 4:3 mode. East-West, East-West Parabola Width are geometry variables to adjust East-West properties.
Page 31
TE2.1E AA EN 31 PAL-BG, PAL-DK, PAL-I, PAL-M, PAL-N, NTSC-M, NTSC-443, SECAM-BG, SECAM- DK, FRANCE: These are all supported signals. By means of these setting display setting can be adjusted according to country transmission systems. Setting one of these bit enables the selection of the corresponding system.
Page 32
TE2.1E AA EN 32 Default values are as follow; Init PHIST V4.19 38.9 SECAM-DK IFL1 33.9 FRANCE SYS-FR SYS-UK SVHS2 AV3S EXP-VA PAL L HP-EXP HB-EXP EW-EXP Vbar PW-EXP SubWoof UCP-EXP Presets LCP-EXP Lock TC-EXP Hotel 16:9 Hpol Vpol Field...
Page 33
TE2.1E AA EN 33 NTSC-M NTSC-443 SECAM-BG P.S.: Blank option bits should be zero. 8.6 OPTION BYTES (ADJUSTED FOR 70TB4417/XX) O P 1 P A L - B G P A L - D K P A L - I...
Page 34
TE2.1E AA EN 34 O P 5 C l o c k A M - P M A V L 1 n o r m A F L O F - T X T M S P - C L I P...
Page 35
TE2.1E AA EN 35 EXP-VA: Vertical amplitude 4:3 EXPAND VS: Vertical slope VSH: Vertical shift EW: East West width for picture setting 4:3 EW-EXP: East West width for picture setting 4:3 EXPAND PW: East West parabola for picture setting 4:3...
Page 36
TE2.1E AA EN 36 It may be necessary after low light alignment to check and to re-align the Remark: high light and to repeat several times the procedure to obtain good alignment for both low and high light. 8.8 TUNER / IF ALIGNMENT 1.
Page 37
TE2.1E AA EN 37 8.10 SYSTEM VOLTAGE ADJUSTMENT Switch the TV in AV mode by pressing AV button on remote control unit. (Minimum beam current condition) Adjust the VAP2 potentiometer until 145Vdc measured on cathode pin of DP08 diode. Please check the other test points and required voltages.
TE2.1E AA EN 38 9. Circuit Descriptions 9.1 Descriptions No descriptions avaialble 9.2 ABBREVIATIONS +BIN System voltage +VMEM Eeprom voltage Auto Gain Control AMOUT AM sound output AV.SW External Video Switch AV.VID Switched Video signal from AV B/G-SND BG Sound...
Page 39
TE2.1E AA EN 39 SC1IR Scart1 sound input right SC1OUTL Scartout Left SC1OUTR Scartout Right SC2IL Scart2 sound input left SC2IR Scart2 sound input right SC2OUTL Scart2 output left SC2OUTR Scart2 output right Clock bus SCL1 Clock bus 1 SCREEN...
Need help?
Do you have a question about the TE2.1E AA and is the answer not in the manual?
Questions and answers