Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. PMW-EX1...
Page 3
Hävitä käytetty paristo valmistajan ohjeiden Remplacer uniquement avec une batterie du même mukaisesti. type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. 1 (P) PMW-EX1...
Related manuals The following manuals are available in this model. If this manual is required, please contact your local Sony Sales Office/Service Center..Operating Instructions (Supplied with the unit) This manual is necessary for application and operation (and installation) of this unit.
_ _ _ _ _ EXT VIEW _ _ _ _ _ No. Signal Specifications LINE_MONI1_L (A/V) LINE OUT (L) LANC_SIG S_GND LANC_DC S OUT (C) LINE_MONI2_R (A/V) LINE OUT (R) AV_SW VIDEO/AUDIO_GND VIDEO Composite OUT S OUT (Y) PMW-EX1...
Page 10
BAT_SCL TPA+ Data on receive, strobe on transmit A (+) BAT_SDA BATT_ID_DATA (USB) : Mini-B connector (5P) BATT (_) _ _ _ _ _ EXT VIEW _ _ _ _ _ No. Signal Specifications USB Vcc USB_ USB+ Ground PMW-EX1...
. EVF signal (analog): To DR-621 board camera signal processor IC (IC100), average value, peak The input/output signals of the baseband processing IC value of the RGB digital video signals that are required for (IC400) are the following signals: PMW-EX1...
Page 13
161 board is input to the balanced input amplifier IC101 Express signals. and IC201 of this board. Output of the balanced amplifi- IC1302 is controlled by PCI bus from IC900. er is connected to the analog switch (IC105, IC205) for switching between [INT/EXT]. PMW-EX1...
Page 15
IC314 of the camera block system, IC400 of the This is the connector board. The audio output from the video signal system, and IC900 of the media recording/ ASW-65 board is connected to A/V multi-connector. playback system. PMW-EX1...
Page 16
IC1001 on the RE-251 board checks that the power switch The PLL circuit is used to reduce jitter of the HD-SDI on the PMW-EX1 is turned ON, and turns on the system clock signal. controller of IC1600. After that, it controls the power for The FPGA (IC100) is controlled by IC400 on the DPR-289 each circuit block according to the system controller.
Page 17
This helps provide detailed information about detection, automatic recovery is not performed and the the battery, including whether the battery is damaged or power must be turned on again. how long the life is, in order to provide optimal operations. PMW-EX1...
Mini USB cable For firmware version-upgrade 3-292-755-01 XLR JIGU For removing the mounted circuit board * : This cable is supplied with PMW-EX1. 1-4-2. Measuring Equipment Use the calibrated equipment or equivalent as listed below for the adjustments. Equipment Model name...
7. Attach the cover on the USB maintenance connector. When the PMW-EX1 is connected to the computer for the first time, the driver software will need to be installed into the computer. For more details, check the readme file that comes with the upgrade software.
1-6. Recommended Replacement Parts This section describes the recommended replacement parts and recommended replacement time. Part name Sony part No. Recommended replacement timing Eye cup 3-278-319-01 Check for deformation and deterioration from time to time. Replace it as necessary. Lens hood...
. The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-13 PMW-EX1...
When connecting the flexible card wire, check the connec- tor shape, and great care should be taken for the direction of the contact surface or isolation surface (blue). Connector : 1 Connector : 2 Isolation surface TX-115 board (A side ) (blue) CN100 Isolation surface (blue) 1-14 PMW-EX1...
Be sure to hold the connector to remove. Polarity marks Hold the connector to remove. Do not attempt to remove by pulling the cables. Contact surface Hold the connector to connect. Not to bend the cable. 1-15 PMW-EX1...
Abnormality in obtaining the lens switch Check the connection with the lens unit. If there is no condition defect, replace the lens unit. 17017 Internal error in the media block Repair the DPR-298 board or replace it. 4XXXX 1-16 PMW-EX1...
: P2 lock ace 2 x 3 the bracket (tripod). 3. Remove the six screws of b and one screw Case (bottom ) L of c, and remove case (bottom) L and case (bottom) R. Bracket (tripod) Case (bottom ) R PMW-EX1...
2-2-3. Microphone Holder Assembly 1. Open the microphone holder assembly. B2.6 x 6 2. Remove the two screws, and remove the microphone holder assembly. Microphone holder assembly 3. Reinstall the microphone holder assembly by reversing the steps of removal. PMW-EX1...
Be very careful not to fold them. 6. Remove the four screws of b, and remove the EVF assembly. Handle cover rear assembly DR-621 board Two claws 7. Reinstall the EVF assembly by reversing the steps of removal. PMW-EX1...
Be sure to hold Flexible card the connector to remove. wire (30 core) Coaxial cable with connector (DPR-LCD) Connector (DPR-289 board) 9. Reinstall the handle assembly by reversing the steps of removal. PMW-EX1...
When removing the outside panel assembly, Inside panel be careful not to drop the battery release assembly button. Outside panel assembly 4. Reinstall the inside panel assembly/outside panel assembly by reversing the steps of removal. PMW-EX1...
7. Reinstall the rear panel assembly by revers- ing the steps of removal. RE-251 board RE-250 board After connecting the harness that has been removed in Step 6, tuck the wires between The wires must be the RE-250 and RE-251 boards. completely tucked in Wires PMW-EX1...
Be careful not to drop the radiation sheet. If Express card assembly the radiation sheet is dropped, install the express card assembly, and then attach the radiation sheet at the position shown in the figure. : P2 lock ace 2 x 3 PMW-EX1...
Page 33
For slot A For slot B figure 1. Be sure that the cable for slot A comes under the cable for slot B. (Fig1) . When reinstalling the express card assem- bly, be careful not to drop the radiation sheet. PMW-EX1...
(CN200) on the RE-250 board. 11. Reinstall the RE-250 board/ RE-251 board by reversing the steps of removal. After connecting the harness that has been removed in Step 9, tuck the wires between the RE-250 and RE-251 boards. 2-10 PMW-EX1...
: P2 lock ace 2 x 2 6. Remove the two screws of c. 7. Remove the three screws of d and remove the bracket. Bracket : P2 lock ace 2 x 3 : P2 lock ace 2 x 3 2-11 PMW-EX1...
Page 36
15. Reinstall the battery case and the TX-115 board by reversing the steps of removal. When reinstalling the HD-SDI assembly, be : P2 lock ace 2 x 3 careful not to drop the radiation sheet. : P2 lock ace 2 x 3 2-12 PMW-EX1...
Flexible boards 2 x 4 : P2 lock ace connectors on the DPR-289 board. 10. Reinstall the DPR-289 board by reversing the steps of removal. When replacing CN-3007 (flexible board), attach the cushion CN3007 (Sony part No.: 3- 286-759-01). 2-13 PMW-EX1...
. Be careful with the position of the flexible board from the prism block when installing the case L assembly. . When reinstalling the main frame that has been removed in Step 3, reinstall the screw of b first. ND filter knob 2-14 PMW-EX1...
BI board (1) Prism assembly 3. Reinstall the prism assembly by reversing the steps of removal. When replacing the prism assembly, attach the BI board cushions (1) (Sony part No.: 3- 291-890-01) to the three positions of the BI board. 2-15 PMW-EX1...
. Check if the installation position of the ND filter aligns with the position of the two reference pins. . When reinstalling the ND filter, loosely fix the three screws, and then fully tighten Reference pin them while paying attention not to deform the ND filter. 2-16 PMW-EX1...
2-2-18. LENS UNIT P2.6 x 5 1. Refer to Sections from 2-2-1 to 2-2-16 and disassemble the unit up to “ND filter” removal. Front sub assembly 2. Remove the five screws, and remove the front sub assembly. Lens unit 2-17 PMW-EX1...
2. Disconnect the harnesses from the connector (CN3) on the DP-621 board. 3. Remove the two screws, and remove the DR- 621 board. DR-621 board 4. Reinstall the DR-621 board by reversing the steps of removal. 2-18 PMW-EX1...
4. Remove the speaker holder sheet, and remove the speaker harness from the slit of the Speaker speaker holder. 5. Remove the speaker from the speaker holder. Speaker holder sheet 6. Reinstall the speaker by reversing the steps of Speaker harness removal. 2-19 PMW-EX1...
5610) from the connector (CN4) on the KSW-53 board. Control switch block 6. Disconnect the HN-320 board from the (ZS-5610) connector (CN1) on the KSW-53 board. KSW-53 board HN-320 board 7. Reinstall the KSW-53 board and HN-320 board by reversing the steps of removal. 2-20 PMW-EX1...
7. Remove the microphone unit assembly in the direction of arrow “D”. Be careful not to hook or damage the har- nesses. Harness (KSW53-MA161) Harness (KSW53-RM213) Microphone unit assembly 8. Reinstall the microphone unit assembly by reversing the steps of removal. 2-21 PMW-EX1...
9. Remove the screw of d, and remove the RM-213 board. Harness MA-161 board (KSW53-RM213) : P2 tapping 2 x 5 : P2 tapping 2 x 5 10. Reinstall the microphone unit by reversing the steps of removal. 2-22 PMW-EX1...
DET-44 board and the DET44 fit plate. 6. Remove the two screws of c, and remove the DET-44 board from the DET44 fit plate. DET-44 board DET44 fit plate 7. Reinstall the DET-44 board by reversing the steps of removal. 2-23 PMW-EX1...
When disconnecting the coaxial cable with connector, do not attempt to remove by pulling the cable. Be sure to hold the connector to remove. LCD bezel 6. Reinstall the 3.5-inch LCD assembly by reversing the steps of removal. 2-24 PMW-EX1...
T/W zoom switch, assemble it by Protrusion rotating it in the direction opposite to the (START/STOP) Notch arrow. (Fig. 2) 3. Install the three screws a, and the screw b. Fig.5 (Fig. 1) Grip cover Buckle Grip belt Fig.6 2-25 PMW-EX1...
Correction Mode Concealment Selects the RPN correction mode that is used to Compensation register or delete the manual registration. Channel Selects and displays the channel (R-ch or G-ch or B-ch) to execute manual registration or detection of RPN correction on. PMW-EX1...
Exiting the Menu Mode device and setting parameters that must be set uniquely to Press the MENU button again. each PMW-EX1 for correction of non-uniformity between The system exits the menu mode to return to the normal the respective lens characteristics.
Page 54
. The Auto BLK Shad menu enables the auto black shading correction (automatic optimization of the respective correction values of the black shading correc- tion). . When Auto BLK Shad menu is selected, the Execute and Cancel choices appear. Selecting Execute starts Auto Black Shading. PMW-EX1...
Page 55
. The V Saw menu enables the vertical Saw black shading correction (linear increase and decrease) level. . The V Para menu enables the vertical Parabola white shading correction (sensitivity correction at the vertical center with respect to both ends) level. PMW-EX1...
Page 56
(such as high illumination or reflective object) inside the picture frame. . Set the lens iris to OPEN. . If the video signal level is too high, use an electronic shutter to a moderate video signal level. . Execute Auto FB Adjust. PMW-EX1...
Cursor V Position, . When the Cursor menu is turned On, the crosshair cursor the RPN cursor moves in the descending order of the indicating the RPN correction position is displayed Cursor H Position.) superimposed on the video signal. PMW-EX1...
. The RPN data that is registered at the factory and the RPN data is manually registered cannot be deleted by the Reset. . When the Reset menu is selected, the Execute and Cancel choices appear. In addition, selecting Execute starts reset of RPN. PMW-EX1...
Page 59
IC to AVIT signal processing IC Item13 4bit I/F while playing back between Diagnosis of the 4bit Bus signal line (playback direction) from display and media block AVIT signal processing IC to base band processing IC PMW-EX1...
Page 60
Shows the number of trials of the self-diagnosis. Success Shows the number of internal successes of the self-diagnosis. Result Shows the result of the self-diagnosis. “0” means no problems. When a value other than “0” is displayed, check the details for each self-diagnostic item. 3-10 PMW-EX1...
Page 61
When an error is detected in the item, it indicates a possible error in the hardware. Item2: Display block diagnosis Display block diagnosis does not function. 3-11 PMW-EX1...
Page 62
Audio block diagnosis analyzes the following contents. Diagnosis description Error value Type 1/2 Note 0x02 Memory area check for -1: Memory read/write 1, 2 audio block comparison NG When an error is detected in the item, it indicates a possible error in the hardware. 3-12 PMW-EX1...
Page 63
When an error is detected in the IIC communication test, it indicates a possible failure in the communication line or device. *: When an error is detected in the version matching test, upgrade again to a compatible version. Contact your local Sony Sales Office/Service Center for information on versions. Item6: Power block diagnosis Power block diagnosis analyzes the following contents.
Page 64
(in the -2: Sequence error direction from AVIT signal processing IC to base band processing) When an error is detected, it indicates a possible failure in the chip or the signal line between chips. 3-14 PMW-EX1...
Section 4 Alignment 4-1. Servicing software “ServiceNavi-EX” Servicing software “ServiceNavi-EX” is required for electrical adjustment and self diagnosis. For how to obtain the “ServiceNavi-EX”, contact your local Sony Sales Office/Service Center. PMW-EX1...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. 3. Stock of Parts Parts marked with “o”...
Handle Cover (Upper) Assembly and EVF 5-2. Exploded Views PMW-EX1...
Page 69
3-278-319-01 s EYE CUP 3-278-644-01 s XDCAM EMBLEM 3-278-648-01 s RUBBER SW KEY 3-285-383-01 s COVER CONNECTOR 3-286-664-01 s HOOD, LENS 3-657-657-02 s SCREW (M5) 4-673-655-01 s SCREW +B 8-753-210-99 s LCX068AK-1 3-056-233-21 s SCREW (M2), LOCK ACE, P2 PMW-EX1...
Page 70
Handle Block 1 PTT2.6 x 6 PTT2.6 x 6 PMW-EX1...
Page 71
7-627-556-57 s PRECISION SCREW +P 2.6X5 TYPE1 3-968-729-52 s SCREW (M2), LOCK ACE, P2 3-282-659-01 s SHEET,HANDLE REAR 3-278-666-02 s RAIL, XLR SW 7-627-556-38 s SCREW +P 2.6X4.0 3-452-727-01 s SHEET, SPEAKER HOLDER 7-685-792-09 s SCREW +PTT 2.6X6 (S) PMW-EX1...
Page 73
3-278-657-01 s CASE, MICROPHONE 3-278-658-01 s HINGE COVER LOWER 3-278-660-01 s MIC CUSION(R) 3-278-661-01 s MIC CUSION(L) 3-278-662-01 s HANDLE (MAIN) 3-278-668-01 s HINGE 3-284-538-01 s SHIELD SHEET(MIC) 3-968-729-52 s SCREW (M2), LOCK ACE, P2 3-278-640-01 s SHEET PANEL BLIND PMW-EX1...
Page 75
3-278-651-01 s LID, LITHIUM BATTERY 3-285-186-01 s SW SPACER 3-701-439-01 s WASHER 3-285-384-01 s CUP BNC 3-729-013-61 s SCREW(M1.4X4.5),WASHERHEAD(+P) 3-968-729-52 s SCREW (M2), LOCK ACE, P2 4-644-493-11 s ACE (M2.6), LOCK 3-080-203-51 s SREW(M2),LOCK ACE,P2 4-644-492-21 s ACE (M2), LOCK PMW-EX1...
Page 77
A-1376-746-A s BATTERY CASE ASSY 1-780-570-11 s TERMINAL BOARD, BATTERY 1-965-708-11 s HARNESS (DPR-EC) 1-965-720-11 s HARNESS, SUB (AU313-BP43) 3-080-203-31 s SREW(M2),LOCK ACE,P2 3-086-368-31 s SCREW (M1.4),LOCK ACE P2 3-278-741-02 s EC-62 LED LENS 3-968-729-52 s SCREW (M2), LOCK ACE, P2 5-11 PMW-EX1...
Page 79
1-965-710-11 s HARNESS (DPR-TX) 1-965-719-11 s HARNESS, SUB (DPR289-TX115) 3-278-726-01 s MAIN FRAME REAR 3-278-727-01 s BNC COVER 3-286-759-01 s CUSHION CN3007 3-968-729-52 s SCREW (M2), LOCK ACE, P2 3-056-233-21 s SCREW (M2), LOCK ACE, P2 3-080-203-01 s SCREW(M2),LOCK ACE,P2 5-13 PMW-EX1...
Page 81
3-285-955-01 s CMOS PROTECTION SHEET A 3-285-956-01 s CMOS PROTECTION SHEET B 3-968-729-52 s SCREW (M2), LOCK ACE, P2 7-627-556-57 s PRECISION SCREW +P 2.6X5 TYPE1 3-294-691-01 s WASHER 3-452-468-01 s BELT, GRIP 3-875-399-01 s LID, REAR 3-875-400-01 s CAP 5-15 PMW-EX1...
Page 82
VCL-EX0877 Part No. SP Description A-1538-803-A s FIXING SCREW ASSY 3-287-626-01 s CAP LENS (F) 3-287-627-01 s CAP LENS (R) 5-16 PMW-EX1...
6-807-802-01 s IC UPD78F0533AGB(S)-402-UEU-A R151 1-208-903-81 s RES, CHIP 4.7K (1005) L100 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) R152 1-208-863-81 s RES, CHIP 100 (1005) L101 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) R153 1-208-863-81 s RES, CHIP 100 (1005) 5-17 PMW-EX1...
Page 84
C136 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C137 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C138 1-124-779-21 s CAP, ELECT 10MF (4.3X5.5) C203 1-164-935-81 s CAP, CHIP CERAMIC 470PF B 1005 C204 1-126-401-21 s CAP, CHIP ELECT 1MF (4X5.7) 5-18 PMW-EX1...
Page 85
8-719-069-61 s DIODE UDZSNPTE-1710B Q302 8-729-112-85 s TRANSISTOR 2SA1330-T1O6 D204 8-719-069-61 s DIODE UDZSNPTE-1710B Q321 6-550-981-01 s TRANSISTOR RN1905(T5RSONY,D,F) D205 8-719-820-42 s DIODE 1SS302-TE85L Q322 8-729-112-85 s TRANSISTOR 2SA1330-T1O6 D206 8-719-820-42 s DIODE 1SS302-TE85L 1-218-911-91 s RES, CHIP 470K (1608) 5-19 PMW-EX1...
Page 86
1-208-943-81 s RES, CHIP 220K (1005) R229 1-208-911-81 s RES, CHIP 10K (1005) R134 1-208-935-81 s RES, CHIP 100K (1005) R230 1-208-891-81 s RES, CHIP 1.5K (1005) R135 1-216-864-91 s CONDUCTOR, CHIP (1608) R231 1-208-891-81 s RES, CHIP 1.5K (1005) 5-20 PMW-EX1...
Page 87
1-208-863-81 s RES, CHIP 100 (1005) R406 1-208-863-81 s RES, CHIP 100 (1005) R409 1-208-927-81 s RES, CHIP 47K (1005) RB401 1-233-578-21 s RES, CHIP NETWORK 47K (3216) RB402 1-233-578-21 s RES, CHIP NETWORK 47K (3216) 1-781-696-31 s VIBRATOR, CRYSTAL (32.768 KHz) 5-21 PMW-EX1...
Page 88
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-208-923-81 s RES, CHIP 33K (1005) 5-22 PMW-EX1...
Page 89
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 5-23 PMW-EX1...
Page 90
1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-220-870-81 s RES, CHIP 10 (1005) 1-208-923-81 s RES, CHIP 33K (1005) 5-24 PMW-EX1...
Page 91
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C234 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C235 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C236 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C237 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-25 PMW-EX1...
Page 92
1-112-197-91 s CAP, CERAMIC 10PF CH (0603) C351 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C559 1-112-197-91 s CAP, CERAMIC 10PF CH (0603) C353 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C560 1-112-197-91 s CAP, CERAMIC 10PF CH (0603) 5-26 PMW-EX1...
Page 93
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C712 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C773 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C713 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C775 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-27 PMW-EX1...
Page 94
1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C940 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1040 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C941 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1041 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) 5-28 PMW-EX1...
Page 95
1-114-569-11 s CAP, CERAMIC 0.01MF X7R 1608 C1310 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1530 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1311 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1531 1-114-570-11 s CAP, CERAMIC 0.068MF X7R 1608 5-29 PMW-EX1...
Page 96
1-820-560-21 s CONNECTOR, COAXIAL(RECEPTACLE) C1589 1-100-881-91 s CAP, CERAMIC 47MF C (3216) CN1300 1-817-456-21 s CONNECTOR, COAXIAL C1590 1-112-716-91 s CAP, CERAMIC 0.1UF B (0603) C1591 1-114-569-11 s CAP, CERAMIC 0.01MF X7R 1608 CN1301 1-817-456-21 s CONNECTOR, COAXIAL 5-30 PMW-EX1...
Page 97
1-400-462-21 s FERRITE, EMI (SMD) (1005) FB411 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB1824 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB501 1-400-462-21 s FERRITE, EMI (SMD) (1005) FB502 1-400-462-21 s FERRITE, EMI (SMD) (1005) IC102 6-703-848-01 s IC SN74CB3T3306DCUR 5-31 PMW-EX1...
Page 98
1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) Q608 8-729-929-27 s TRANSISTOR DTC114TE-TL L404 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) Q1100 6-550-832-01 s TRANSISTOR SI2301BDS-T1 L405 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) Q1500 6-550-119-01 s TRANSISTOR DTC144EMT2L L406 1-469-549-21 s INDUCTOR, CHIP 1.0UH (LB2016) 5-32 PMW-EX1...
Page 99
1-240-718-91 s RES, CHIP 100K (0603) R312 1-240-718-91 s RES, CHIP 100K (0603) R390 1-240-695-91 s RES, CHIP 1K (0603) R313 1-240-683-91 s RES, CHIP 100 (0603) R391 1-240-707-91 s RES, CHIP 10K (0603) R392 1-240-679-91 s RES, CHIP 47 (0603) 5-33 PMW-EX1...
Page 100
1-240-762-91 s RES, CHIP 120 (0603) R548 1-240-772-91 s RES, CHIP 330 (0603) R464 1-240-784-91 s RES, CHIP 1K (0603) R549 1-240-772-91 s RES, CHIP 330 (0603) R465 1-240-695-91 s RES, CHIP 1K (0603) R550 1-240-772-91 s RES, CHIP 330 (0603) 5-34 PMW-EX1...
Page 101
1-240-676-91 s RES, CHIP 22 (0603) R913 1-240-714-91 s RES, CHIP 47K (0603) R649 1-240-676-91 s RES, CHIP 22 (0603) R914 1-240-714-91 s RES, CHIP 47K (0603) R650 1-240-676-91 s RES, CHIP 22 (0603) R915 1-240-714-91 s RES, CHIP 47K (0603) 5-35 PMW-EX1...
Page 102
1-240-749-91 s RES, CHIP 36 (0603) R1258 1-240-695-91 s RES, CHIP 1K (0603) R1114 1-240-749-91 s RES, CHIP 36 (0603) R1259 1-240-807-91 s RES, CHIP 9.1K (0603) R1115 1-240-788-91 s RES, CHIP 1.5K (0603) R1260 1-240-680-91 s RES, CHIP 56 (0603) 5-36 PMW-EX1...
Page 103
1-240-752-91 s RES, CHIP 47 (0603) R1631 1-240-718-91 s RES, CHIP 100K (0603) R1424 1-240-752-91 s RES, CHIP 47 (0603) R1632 1-240-676-91 s RES, CHIP 22 (0603) R1425 1-240-752-91 s RES, CHIP 47 (0603) R1633 1-240-676-91 s RES, CHIP 22 (0603) 5-37 PMW-EX1...
Page 104
1-240-759-91 s RES, CHIP 91 (0603) R2516 1-240-759-91 s RES, CHIP 91 (0603) R2517 1-240-754-91 s RES, CHIP 56 (0603) R2518 1-240-764-91 s RES, CHIP 150 (0603) R2519 1-240-777-91 s RES, CHIP 510 (0603) R2520 1-240-778-91 s RES, CHIP 560 (0603) 5-38 PMW-EX1...
Page 105
8-729-928-25 s TRANSISTOR 2SA1774TL-QR 6-550-119-01 s TRANSISTOR DTC144EMT2L 6-550-232-01 s TRANSISTOR 2SA2029T2LQ/R 6-551-797-01 s TR UNR92A3G0LS0 8-729-427-76 s TRANSISTOR XP4601-TXE 6-551-797-01 s TR UNR92A3G0LS0 8-729-427-76 s TRANSISTOR XP4601-TXE 1-208-935-81 s RES, CHIP 100K (1005) 1-208-935-81 s RES, CHIP 100K (1005) 5-39 PMW-EX1...
Page 106
1-794-276-21 o CONNECTOR, SQUARE TYPE 4P 6-500-750-01 s DIODE NSAD500H-T1-A 1-400-476-11 s COMMON MODE CHOKE COIL 1-218-990-81 s CONDUCTOR, CHIP (1005) THP1 1-805-726-11 s THERMISTOR, POSITIVE THP2 1-805-726-11 s THERMISTOR, POSITIVE THP3 1-805-726-11 s THERMISTOR, POSITIVE THP4 1-805-726-11 s THERMISTOR, POSITIVE 5-40 PMW-EX1...
Page 107
1-218-941-81 s RES, CHIP 100 VDR8 1-802-245-11 s ESD SUPPRESSOR R104 1-218-977-81 s RES, CHIP 100K VDR9 1-802-245-11 s ESD SUPPRESSOR R105 1-220-874-81 s RES, CHIP 15 (1005) R107 1-220-876-81 s RES, CHIP 18 (1005) R109 1-208-855-81 s RES, CHIP 47 (1005) 5-41 PMW-EX1...
Page 108
1-208-927-81 s RES, CHIP 47K (1005) R121 1-208-911-81 s RES, CHIP 10K (1005) R122 1-208-911-81 s RES, CHIP 10K (1005) R123 1-208-911-81 s RES, CHIP 10K (1005) R124 1-208-911-81 s RES, CHIP 10K (1005) R125 1-208-927-81 s RES, CHIP 47K (1005) 5-42 PMW-EX1...
Page 109
1-208-947-81 s RES, CHIP 330K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-883-81 s RES, CHIP 680 (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-883-81 s RES, CHIP 680 (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 5-43 PMW-EX1...
Page 110
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C206 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C207 1-165-989-91 s CAP, CERAMIC 10MF (2012) C208 1-165-989-91 s CAP, CERAMIC 10MF (2012) C209 1-165-989-91 s CAP, CERAMIC 10MF (2012) 5-44 PMW-EX1...
Page 111
8-759-338-95 s IC NJM2903V(TE2) 8-719-938-77 s DIODE SB05-05C-TB-E 8-719-069-28 s DIODE 1SS400TE-61 1-456-622-21 s COIL, CHOKE 1UH 8-719-069-28 s DIODE 1SS400TE-61 1-456-622-21 s COIL, CHOKE 1UH 1-457-045-11 s COIL, CHOKE (8.2UH) 8-719-069-28 s DIODE 1SS400TE-61 1-457-045-11 s COIL, CHOKE (8.2UH) 5-45 PMW-EX1...
Page 112
1-208-935-81 s RES, CHIP 100K (1005) Q204 8-729-928-28 s TRANSISTOR DTA144EE-TL 1-208-911-81 s RES, CHIP 10K (1005) Q205 8-729-928-28 s TRANSISTOR DTA144EE-TL 1-208-915-81 s RES, CHIP 15K (1005) Q206 8-729-928-28 s TRANSISTOR DTA144EE-TL 1-218-990-81 s CONDUCTOR, CHIP (1005) Q207 8-729-928-28 s TRANSISTOR DTA144EE-TL 5-46 PMW-EX1...
Page 113
1-218-990-81 s CONDUCTOR, CHIP (1005) R231 1-208-927-81 s RES, CHIP 47K (1005) R101 1-208-919-81 s RES, CHIP 22K (1005) R232 1-208-927-81 s RES, CHIP 47K (1005) R102 1-208-919-81 s RES, CHIP 22K (1005) R233 1-208-927-81 s RES, CHIP 47K (1005) 5-47 PMW-EX1...
Page 114
1-208-887-81 s RES, CHIP 1.0K (1005) R333 1-208-879-81 s RES, CHIP 470 (1005) R334 1-219-611-21 s RES, CHIP (SQUARE TYPE) 0.047 R338 1-208-935-81 s RES, CHIP 100K (1005) R339 1-208-935-81 s RES, CHIP 100K (1005) R341 1-208-959-81 s RES, CHIP 1M (1005) 5-48 PMW-EX1...
Page 115
Q107 8-729-929-27 s TRANSISTOR DTC114TE-TL Q108 8-729-929-27 s TRANSISTOR DTC114TE-TL C1015 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 Q109 8-729-929-27 s TRANSISTOR DTC114TE-TL C1016 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 Q112 6-551-523-01 s TRANSISTOR SI7114DN-T1-E3 5-49 PMW-EX1...
Page 116
1-208-959-81 s RES, CHIP 1M (1005) R102 1-208-959-81 s RES, CHIP 1M (1005) R103 1-208-959-81 s RES, CHIP 1M (1005) R106 1-208-927-81 s RES, CHIP 47K (1005) R107 1-208-927-81 s RES, CHIP 47K (1005) R108 1-208-927-81 s RES, CHIP 47K (1005) 5-50 PMW-EX1...
Page 117
1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-208-895-81 s RES, CHIP 2.2K (1005) 1-786-157-51 s TACTILE SWITCH 1-762-650-21 s SWITCH, SLIDE 1-786-157-51 s TACTILE SWITCH 1-479-022-71 s SENSOR, ANGULAR VELOCITY 1-479-022-81 s SENSOR, ANGULAR VELOCITY 5-51 PMW-EX1...
Page 118
1-208-895-81 s RES, CHIP 2.2K (1005) R500 1-208-927-81 s RES, CHIP 47K (1005) R501 1-208-927-81 s RES, CHIP 47K (1005) R502 1-208-927-81 s RES, CHIP 47K (1005) R504 1-208-863-81 s RES, CHIP 100 (1005) R505 1-208-895-81 s RES, CHIP 2.2K (1005) 5-52 PMW-EX1...
Page 119
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C406 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C407 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C500 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C501 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 5-53 PMW-EX1...
Page 120
1-208-919-81 s RES, CHIP 22K (1005) IC103 8-759-592-49 s IC TC7SZ125FU(TE85R) IC104 6-707-853-01 s IC TC74LCX541FT(EKJ) R308 1-208-863-81 s RES, CHIP 100 (1005) IC200 6-709-619-01 s IC GS1578ACNE3 R309 1-208-863-81 s RES, CHIP 100 (1005) R310 1-208-887-81 s RES, CHIP 1.0K (1005) 5-54 PMW-EX1...
1-208-955-81 s RES, CHIP 680K (1005) R713 1-218-990-81 s CONDUCTOR, CHIP (1005) R714 1-208-951-81 s RES, CHIP 470K (1005) R715 1-208-911-81 s RES, CHIP 10K (1005) R719 1-208-935-81 s RES, CHIP 100K (1005) R720 1-218-990-81 s CONDUCTOR, CHIP (1005) 5-55 PMW-EX1...
Page 123
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-06) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
Need help?
Do you have a question about the PMW-EX1 and is the answer not in the manual?
Questions and answers