RM-EA002 SERVICE MANUAL CHASSIS MODEL MODEL COMMANDER DEST COMMANDER DEST KLV-S19A10E KLV-S19A10U RM-EA002 RM-EA002 KLV-S19A10 RM-EA002 FLAT PANEL COLOR TV - 1 -...
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE DIRECTLY CONNECTED TO THE POWER LINE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
RM-EA002 . s l . s l . s l e i l i g i a j i i n i i n i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating.
RM-EA002 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left) Output impedence : Less than 1kohm*...
RM-EA002 WAX SELF DIAGNOSTIC SOFTWARE The identification of errors within the WAX chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
RM-EA002 SECTION 3 SET-UP ADJUSTMENTS 3-1. Signal Adjustment 3-2. White Balance Adjustment Service adjustments to this model can be performed using the 3-2-1. White Balance adjustment (H/L) supplied remote Commander RM-EA002. 1. Select AV0. How to enter into the Service Mode 2.
RM-EA002 3-2-2. White Balance adjustment (C/O) 3-2-3. SECAM White Balance adjustment (H/L) 1. Select AV0. 1. Select AV0. 2. Change the TV to Custom Mode and set the following registers by 2. Change the TV to Custom Mode and set the following registers by sending “TT54”.
RM-EA002 3-2-4. SECAM White Balance adjustment (C/O) 3-3. TEST TEST MODE 1. Select AV0. Test Test Mode is available in Service Mode, OSD ‘TT’ appears. The 2. Change the TV to Custom Mode and set the following registers by functions described below are available by selecting the two numbers. sending “TT54”.
~ BE Printed Wiring Board Conductor Side A ~ ~ BE Board Semiconductor Location Table Side A ~ ~ BE Printed Wiring Board Conductor Side B ~ ~ BE Board Semiconductor Location Table Side B ~ - 42 -...
~ H1E Printed Wiring Board Conductor Side A ~ ~ H1E Printed Wiring Board Conductor Side B ~ ~ TU Printed Wiring Board Conductor Side A ~ ~ TU Printed Wiring Board Conductor Side B ~ ~ H3 Printed Wiring Board Conductor Side A ~ ~ H3 Printed Wiring Board Conductor Side B ~ - 44 -...
....................61 TU BOARD COMMON Parts List : Parts common to all models listed in this manual ...... 61 Model Parts that belong only to the model specified KLV-S19A10E ....................62 KLV-S19A10U ....................62 BE BOARD COMPLETE Parts List : ....................
Need help?
Do you have a question about the KLV-S19A10E and is the answer not in the manual?
Questions and answers