All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by ER/TY 1062 BU TV Consumer Care, the Netherlands...
Figures can deviate due to the different set executions. • Specifications are indicative (subject to change). Table 2-1 Described Model numbers and diversity Conn Mechanics Descriptions Wng Schematics Styling styling sh. 32PFL5405H/05 Rembrandt 64025 10-31 2.3 4-1 4.5 4.5.9 7.2 7.4.1 7.10 9-1 10-23 10-25 11-1...
Page 3
Technical Specifications, Diversity, and Connections Q552.1E LA EN 3 Connections 18770_001_100210.eps 100210 Figure 2-1 Connection overview Note: The following connector colour abbreviations are used - Vdd Supply (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= - CLOCK Signal Grey, Rd= Red, Wh= White, Ye= Yellow.
Page 4
EN 4 Q552.1E LA Technical Specifications, Diversity, and Connections 4 - HDMI: Digital Video, Digital Audio - In 14 - Ground P50 15 - Video Red 0.7 V / 75 ohm 16 - Status/FBL 0 - 0.4 V: INT 1 - 3 V: EXT / 75 ohm 10000_017_090121.eps 17 - Ground Video 090428...
Page 5
Technical Specifications, Diversity, and Connections Q552.1E LA EN 5 16 - VGA: Video RGB - In 10000_002_090121.eps 090127 Figure 2-8 VGA Connector - Video Red 0.7 V / 75 ohm - Video Green 0.7 V / 75 ohm - Video Blue 0.7 V / 75 ohm - n.c.
Spare Parts • Check the strain relief of the Mains/AC Power cord for proper function. For the latest spare part overview, consult your Philips Spare • Check the electrical DC resistance between the Mains/AC Part web portal. Power plug and the secondary side (only for sets that have a Mains/AC Power isolated power supply): 1.
Page 7
Precautions, Notes, and Abbreviation List Q552.1E LA EN 7 3.3.6 Alternative BOM identification Abbreviation List It should be noted that on the European Service website, 0/6/12 SCART switch control signal on A/V “Alternative BOM” is referred to as “Design variant”. board.
Page 8
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 9
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
EN 10 Q552.1E LA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing Rembrandt series • Figures below can deviate slightly from the actual situation, 4.2 Cable Dressing Van Gogh styling due to the different set executions. 4.3 Cable Dressing Matisse styling 4.4 Service Positions 4.5 Assy/Panel Removal Rembrandt Styling...
Page 11
Mechanical Instructions Q552.1E LA EN 11 18770_101_100211.eps 100216 Figure 4-2 Cable dressing 37PFL5405H/xx 18770_102_100211.eps 100211 Figure 4-3 Cable dressing 42PFL5405H/xx back to 2010-Feb-19 div. table...
Page 12
EN 12 Q552.1E LA Mechanical Instructions Cable Dressing Van Gogh styling 18770_103_100211.eps 100211 Figure 4-4 Cable dressing 32PFL5605H/xx 18770_105_100211.eps 100216 Figure 4-5 Cable dressing 40PFL5605H/xx without DVB-S back to 2010-Feb-19 div. table...
Page 13
Mechanical Instructions Q552.1E LA EN 13 18770_104_100211.eps 100211 Figure 4-6 Cable dressing 40PFL5605H/xx with DVB-S back to 2010-Feb-19 div. table...
Page 14
EN 14 Q552.1E LA Mechanical Instructions Cable Dressing Matisse styling 18770_106_100211.eps 100211 Figure 4-7 Cable dressing 32PFL7605H/xx 18770_107_100211.eps 100211 Figure 4-8 Cable dressing 40PFL7605H/xx back to 2010-Feb-19 div. table...
Page 15
Mechanical Instructions Q552.1E LA EN 15 Service Positions The stand and -subframe do not need to be removed for removing the central subwoofer. When defective, replace the whole unit. For easy servicing of a TV set, the set should be put face down on a soft flat surface, foam buffers or other specific workshop 4.5.3 Mains Switch...
Page 16
EN 16 Q552.1E LA Mechanical Instructions 4.5.5 Small Signal Board (SSB) Refer to Figure 4-12 Figure 4-13 for details. 18770_125_100215.eps 100215 Figure 4-13 SSB - back shielding 18770_124_100215.eps 100217 1. Unplug all connectors [1] and [2]. 2. Remove the fixation screws [3]. Figure 4-12 SSB 3.
Page 17
Mechanical Instructions Q552.1E LA EN 17 4.5.9 LCD Panel Refer to Figure 4-17 Figure 4-18 for details. 18770_127_100215.eps 100215 Figure 4-15 IR & LED board 1. Detach the front bezel from the set as earlier described. 2. Release the clips [1] that secure the IR & LED board in the bezel and take the board out.
Page 18
EN 18 Q552.1E LA Mechanical Instructions Do not release Do not release 18770_121_100212.eps 100212 Figure 4-18 LCD board -2- Warning! The snaps on the backside of the LCD Panel secure the backlight units and should never be released! 1. Remove the tweeters as earlier described. 2.
Page 19
Mechanical Instructions Q552.1E LA EN 19 Assy/Panel Removal Van Gogh Styling The instructions apply to the 46PFL5605H/xx. 4.6.1 Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. Note: it is not necessary to remove the stand while removing the rear cover.
Page 20
EN 20 Q552.1E LA Mechanical Instructions 4.6.3 Main Power Supply Refer to Figure 4-23 for details. 18770_142_100215.eps 100215 Figure 4-25 IR & LED Board -1- 18770_140_100215.eps 100217 Figure 4-23 Main Power Supply 1. Unplug all connectors [1]. 2. Remove the fixation screws [2]. 3.
Page 21
Mechanical Instructions Q552.1E LA EN 21 18770_144_100215.eps 100215 Figure 4-27 IR & LED Board -3- 1. Remove the stand [1]. 2. Remove the IR & LED board cover [2]. 3. Release the clips [3] that secure the IR & LED board. 4.
Page 22
EN 22 Q552.1E LA Mechanical Instructions 18770_146_100216.eps 100216 Figure 4-29 LCD Panel Assy/Panel Removal Matisse Styling Set Re-assembly The Matisse styling is similar to the Van Gogh styling. No To re-assemble the whole set, execute all processes in reverse detailed information is available at time of publishing. order.
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 23 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • All service-unfriendly modes (if present) are disabled, like: 5.1 Test Points – (Sleep) timer. 5.2 Service Modes –...
Page 24
Code continue by pressing the “OK” button on the RC. 39mm Contents of SAM (see also Table 6-10) PHILIPS MODEL: • Hardware Info. 32PF9968/10 – A. SW Version. Displays the software version of the PROD.SERIAL NO:...
Page 25
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 25 • With the “OK” key, it is possible to activate the selected • Installed date. Indicates the date of the first installation of action. the TV. This date is acquired via time extraction. •...
Page 26
EN 26 Q552.1E LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up 7U0X or others FET’s on shortcircuit before activating SDM via the service pads. When the TV is in a protection state due to an error detected by stand-by software (error blinking is displayed) and SDM is activated via shortcutting the SDM solder path on the SSB, the The abbreviations “SP”...
Page 27
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 27 Stand by or Mains is applied Protection Standby Supply starts running. All standby supply voltages become available. st-by µP resets If the protection state was left by short circuiting the Initialise I/O pins of the st-by µP: SDM pins, detection of a protection condition during - Switch reset-AVC LOW (reset state)
Page 28
EN 28 Q552.1E LA Service Modes, Error Codes, and Fault Finding Reset-system is switched HIGH by the Reset-system is switched HIGH by the AVC at the end of the bootscript AVC at the end of the bootscript AVC releases Reset-Ethernet, Reset-USB and AVC releases Reset-Ethernet, Reset-USB and Reset-DVBs when the end of the AVC boot- Reset-DVBs when the end of the AVC boot-...
Page 29
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 29 Constraints taken into account: - Display may only be started when valid LVDS output clock can be delivered by the AVC. - To have a reliable operation of the EEFL backlight, the backlight should be driven with a maximum PWM duty cycle during the first seconds.
Page 30
EN 30 Q552.1E LA Service Modes, Error Codes, and Fault Finding Semi Standby The assumption here is that a fast toggle (<2s) can only happen during ON->SEMI ->ON. In these states, the AVC is still active and can provide the 2s delay. If the transition ON->SEMI- >STBY->SEMI->ON can be made in less than 2s, Wait until previous on-state is left more than 2 seconds ago.
Page 31
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 31 Active Mute all sound outputs via softmute Wait 100ms Set main amplifier mute (I/O: audio-mute) Force ext audio outputs to ground (I/O: audio reset) And wait 5ms switch off Ambilight Wait until Ambilight has faded out: Output power Observer should be zero Switch off POK line...
Page 32
EN 32 Q552.1E LA Service Modes, Error Codes, and Fault Finding Semi Stand by If ambientlight functionality was used in semi-standby (lampadaire mode), switch off ambient light (see CHS ambilight) *) If this is not performed and the set is Delay transition until ramping down of ambient light is switched to standby when the switch off of finished.
Page 33
Introduction The error code buffer contains all detected errors since the last ComPair (Computer Aided Repair) is a Service tool for Philips time the buffer was erased. The buffer is written from left to Consumer Electronics products. and offers the following: right, new errors are logged at the left side, and all other errors 1.
Page 34
EN 34 Q552.1E LA Service Modes, Error Codes, and Fault Finding • Via the blinking LED procedure. See section 5.5.3 How to content, as this history can give significant information). This to Clear the Error Buffer. ensure that old error codes are no longer present. •...
Page 35
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 35 will be logged and displayed via the blinking LED 6. The sequence starts again. procedure if SDM is activated. • Error 34 (Tuner). When there is no I C communication 5.6.2 How to Activate towards the tuner during start-up, LAYER 2 error = 34 will...
Page 36
EN 36 Q552.1E LA Service Modes, Error Codes, and Fault Finding Fault Finding and Repair Tips +12V is considered OK (=> DETECT2 signal becomes high, +12V to +1V8, +12V to +3V3, +12V to +5V DC-DC converter can be started up) if it rises above 10V and doesn’t drop below Read also section “5.5 Error Codes,...
Page 37
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 37 Then push the “SOURCE” button for 10 seconds until the “F” disappears from the screen. 5.8.6 Logging When something is wrong with the TV set (f.i. the set is rebooting) you can check for more information via the logging in Hyperterminal.
Page 38
Before starting: - prepare a USB memory stick with the latest software - download the latest Main Software (Fus) from www.p4c.philips.com - unzip this file - create a folder ”upgrades” in the root of a USB stick (size > 50 MB) and save the autorun.upg file in this "upgrades"...
Page 39
Service Modes, Error Codes, and Fault Finding Q552.1E LA EN 39 Set is st art in g u p in F act o ry m o d e Set is starting up in F actory m ode? Noisy picture with bands/lines is visible and the An “F”...
Page 40
How to start the software upgrade application manually: 1. Disconnect the TV from the Mains/AC Power. 5.9.5 UART logging 2K10 (see section “5.8 Fault Finding and 2. Press the “OK” button on a Philips TV remote control or a Repair Tips, 5.8.6 Logging) Philips DVD RC-6 remote control (it is also possible to use a TV remote in “DVD”...
Alignments Q552.1E LA EN 41 6. Alignments Index of this chapter: For the next alignments, supply the following test signals via a 6.1 General Alignment Conditions video generator to the RF input: 6.2 Hardware Alignments • EU/AP-PAL models: a PAL B/G TV-signal with a signal 6.3 Software Alignments strength of at least 1 mV and a frequency of 475.25 MHz 6.4 Option Settings...
Page 42
EN 42 Q552.1E LA Alignments Table 6-2 White D alignment values LED backlight panels - Option Settings colour analyser Minolta CA-210 6.4.1 Introduction Value Cool (9420K) Normal (8120K) Warm (6080K) 0.282 0.292 0.320 The microprocessor communicates with a large number of I 0.298 0.311 0.345...
Page 43
OK on the remote control 2. Download the latest main software (FUS) from the before the cursor is moved to the left! www.p4c.philips.com website. 3. Create a folder “upgrades” in the root of a USB stick (size Reset of Repaired SSB >...
Page 44
EN 44 Q552.1E LA Alignments Total Overview SAM modes Table 6-10 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Hardware Info A. SW version e.g. “Q5521_0.33.0.0 Display TV & Standby SW version and CTN serial number B.
Page 45
Alignments Q552.1E LA EN 45 Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Options Digital broadcast Off/On Select DVB On/Off DVB - T installation Off/On or Country dependent Select DVB T installation On/Off or by country DVB - T light Off/On Select DVB T light On/Off DVB - C...
Page 46
EN 46 Q552.1E LA Alignments Main Menu Sub-menu 1 Sub-menu 2 Sub-menu 3 Description Option numbers Group 1 e.g. “00008.01793.15421.08192” The first line (group 1) indicates hardware options 1 to 4 Group 2 e.g. “44013.34315.00000.00000” The second line (group 2) indicates software options 5 to 8 Store Store after changing...
Circuit Descriptions Q552.1E LA EN 47 7. Circuit Descriptions Index of this chapter: Introduction 7.1 Introduction 7.2 Power Architecture The Q552.1E LA chassis is part of the TV550 platform and 7.3 DC/DC Converters comes with the following stylings: “Rembrandt” (series 7.4 Front-End Analogue and DVB-T, DVB-C;...
Page 48
EN 48 Q552.1E LA Circuit Descriptions 18770_245_100203.eps 100219 Figure 7-2 Architecture of TV550 platform - TCON integrated on SSB back to 2010-Feb-19 div. table...
Page 49
Circuit Descriptions Q552.1E LA EN 49 7.1.3 SSB Cell Layout 1M 3 6 1M 20 1M 71 1 M 59 2D D IM 1G 51 1G 50 D D R 2 F P G A D C /D C D D R 2 LVD S - O U T S D- S L O T PN X85500...
Page 50
EN 50 Q552.1E LA Circuit Descriptions 1 M 3 6 1 G 51 1G 50 1 M20 1M 71 1 M59 2 D D IM T C O N D V B - S Quad LVDS 1 M 3 6 1 G 51 1G 50 1 M20...
Page 51
Circuit Descriptions Q552.1E LA EN 51 Power Architecture Refer to figure Figure 7-6 for the power architecture of this platform. 18770_234_100127.eps 100127 Figure 7-6 Power Architecture TV550 platform 7.2.1 Power Supply Unit • Output to the display; in case of - IPB: High voltage to the LCD panel - PSL and PSLS (LED-driver outputs) All power supplies are a black box for Service.
Page 52
EN 52 Q552.1E LA Circuit Descriptions PSL stands for Power Supply with integrated LED-drivers. • a +24V under-voltage detection circuitry is built around PSLS stands for a Power Supply with integrated LED-drivers item no. 7T04 with added Scanning functionality (added microcontroller). •...
Page 53
Circuit Descriptions Q552.1E LA EN 53 Front-End Analogue and DVB-T, DVB-C; • Channel decoder; I C address 0xD0 • LNB switching regulator; I C address 0x14 ISDB-T reception • Amplifier • PNX85500 SoC TV processor with integrated DVB-T and 7.4.1 European/China region DVB-C channel decoder and analogue demodulator.
Page 54
EN 54 Q552.1E LA Circuit Descriptions • Sil9287B (supports “Instaport” technology for fast • High definition ME/MC switching between input signals). • 2D LED backlight dimming option The hardware default I C addresses are: • Embedded HDMI HDCP keys • Sil9187A: 0xB0/0xB2 (random: software workaround) •...
Page 55
Circuit Descriptions Q552.1E LA EN 55 Back-End The following backlight types can be distinguished: • CCFL/EEFL backlight; applicable to the xxPFL54xx sets • LED backlight: - side-view (edge) LED without scanning: PSL power board; applicable to xxPFL76xx sets - side-view (edge) LED with scanning: PSLS power board; not applicable to this chassis - direct-view LED with 0D-dimming: PSL power board;...
Page 56
EN 56 Q552.1E LA Circuit Descriptions +3V3 7B20-1 74LVC2G17 3B01-2 3B30-1 PWM-CLOCK-BUF PWM-CLOCK × 100R 220R × × 7B20-2 × × 74LVC2G17 +3V3 3B01-1 3B30-4 × SPI-CLOCK-BUF SPI-CLOCK 100R 220R 18770_214_100126.eps 100126 Figure 7-20 Ambilight buffer 18770_210_100126.eps The temperature sensor is built around item no. 7B30 (diagram 100126 AL1A) and indicates overtemperature of the board.
Page 58
EN 58 Q552.1E LA Circuit Descriptions EEPROM LVDS (10 bit) Mini - LVDS Timing Controller Control Signals Gamma Reference Source Drive IC Voltage +3.3 V +1.8 V +16 V TFT – LCD Panel +12 V Power Block (+28 V) (-6 V) M ain P latform T C O N LC D P anel...
Page 59
Circuit Descriptions Q552.1E LA EN 59 Notes to figure 7-26 TCON block diagram: • Timing Control Function: generates control signals to • LVDS receiver: converts the data stream back into RGB column drivers and row drivers (Source Enable - SOE, data and SYNC signals (Vsync, Hsync, Data Enable - DE) Gate Enable - GOE, Gate Start Pulse - GSP).
EN 60 Q552.1E LA IC Data Sheets 8. IC Data Sheets This chapter shows the internal block diagrams and pin electrical diagrams (with the exception of “memory” and “logic” configurations of ICs that are drawn as “black boxes” in the ICs).
Page 61
IC Data Sheets Q552.1E LA EN 61 Diagram Temp Sensor + Headphone B01J, LM75BDP (IC 7FD1) Block diagram LM75B BIAS POINTER CONFIGURATION REFERENCE REGISTER REGISTER TEMPERATURE COUNTER BAND GAP REGISTER 11-BIT TEMP SENSOR SIGMA-DELTA A-to-D TIMER REGISTER CONVERTER OSCILLATOR COMPARATOR/ THYST INTERRUPT REGISTER...
Page 62
EN 62 Q552.1E LA IC Data Sheets Diagram PNX NandFlash - Conditional Access B02A, PNX85500 (IC7S00) Block diagram PNX8550x MEMORY CONTROLLER TS input MPEG SYSTEM CI/CA LVDS for PRIMARY TS out/in for PROCESSOR flat panel display PCMCIA VIDEO LVDS (single, dual or OUTPUT quad channel) DVB-T/C...
Page 63
IC Data Sheets Q552.1E LA EN 63 Diagram Audio B03A, TPA3120D2PWP (IC7D10) Block Diagram TPA3120D2 0.22 F 22 H 470 F ROUT 0.68 F PGNDR 0.68 F PGNDL LOUT BYPASS 22 H 470 F AGND 0.22 F PVCCL AVCC PVCCR VCLAMP Shutdown Control...
Page 64
EN 64 Q552.1E LA IC Data Sheets Diagram DC/DC B03B, TPS53126PW (IC7U03) Block Diagram Pin Configuration VBST1 DRVH1 DRVL1 PGND1 VFB1 TRIP1 VREG5 TEST1 V5FILT TEST2 VFB2 TRIP2 PGND2 DRVL2 DRVH2 VBST2 18250_300_090319.eps 090319 Figure 8-5 Internal block diagram and pin configuration back to 2010-Feb-19 div.
Page 65
IC Data Sheets Q552.1E LA EN 65 Diagram DC/DC B03E, ST1S10PH (IC 7UD0) Block Diagram Pin Configuration DFN8 (4x4) PowerSO-8 I_18010_083.eps 130608 Figure 8-6 Internal block diagram and pin configuration back to 2010-Feb-19 div. table...
Page 66
EN 66 Q552.1E LA IC Data Sheets Diagram DC/DC B03E, LD1117DT25 (IC 7UD2) Block Diagram Pin Configuration LD1117DT DPAK F_15710_166.eps 230905 Figure 8-7 Internal block diagram and pin configuration back to 2010-Feb-19 div. table...
Page 67
IC Data Sheets Q552.1E LA EN 67 Diagram Ethernet + Service B04C, LAN8710A-EZKH (IC 7E10) Block diagram MODE0 HP Auto-MDIX Auto- 10M Tx MODE1 MODE Control Negotiation Logic Transmitter TXP / TXN MODE2 Reset Transmit Section RXP / RXN nRST Control 100M Tx 100M...
Page 68
EN 68 Q552.1E LA IC Data Sheets Diagram HDMI B04D, SII9287B (IC 7EC1) Block diagram Pinning information 18770_303_100217.eps 100217 Figure 8-9 Internal block diagram and pin configuration back to 2010-Feb-19 div. table...
Page 69
IC Data Sheets Q552.1E LA EN 69 8.10 Diagram Headphone B04E, TPA6111A2DGN (IC 7EE1) Block diagram IN 1− − BYPASS IN 2− − SHUTDOWN Bias Control Pinning information D OR DGN PACKAGE (TOP VIEW) IN1− BYPASS IN2− SHUTDOWN 18770_309_100217.eps 100217 Figure 8-10 Internal block diagram and pin configuration back to 2010-Feb-19...
Page 70
EN 70 Q552.1E LA IC Data Sheets 8.11 Diagram Circuit Diagrams and PWB Layouts B07A, STV6110AT (IC 7R02) Block diagram RF_OUT RF_IN PLL, dividers DC offset compensation XTAL_IN C bus interface Amplifier XTAL_INN XTAL_OUT 18770_304_100217.eps 100217 Figure 8-11 Internal block diagram and pin configuration back to 2010-Feb-19 div.
Page 71
IC Data Sheets Q552.1E LA EN 71 8.12 Diagram Circuit Diagrams and PWB Layouts B08A, TPS54283PWP (IC 7T03) Block diagram BOOT1 CLK1 Level PVDD1 Shift Current ) + DC(ofst) Comparator DRAIN1 DRAIN1 Overcurrent Comp 0.8 V COMP SLOPE1 MAX1 Weak Soft Start CLK1 Pull-Down...
Page 72
EN 72 Q552.1E LA IC Data Sheets 8.13 Diagram Circuit Diagrams and PWB Layouts B08B, LNBH23Q (IC 7T50) Block diagram ISEL ISEL ADDR ADDR SDA SCL SDA SCL Vcc- Vcc- Vcc- Preregulator Preregulator +U.V.lockout +U.V.lockout +P.ON reset +P.ON reset Rsense Rsense VSEL VSEL...
Page 74
EN 74 Q552.1E LA IC Data Sheets 8.15 Diagram TCON Controller B11B, TPS62110RSA (IC 7JH1) Block diagram Undervoltage Vina Lockout Thermal Shutdown Comparator 1-MHz (COMP) Oscillator P-Channel Comparator Driver Shoot-Through Control Sawtooth Logic Logic Generator N-Channel SKIP Comparator Compensation The internal feedback divider is disabled and the FB pin is directly connected to the internal GM amplifier.
Circuit Diagrams and PWB Layouts Q552.1E LA EN 87 10. Circuit Diagrams and PWB Layouts 10-1 AL1 820400089786 AmbiLight Common LiteOn LED Common 1 LiteOn 15 LED Common AL1A AL1A 1M83 C1 +3V3 2B00 E8 2B11 2B01 F8 2B02 E9 100n 2B03 I14 FH12-25S-0.5SH(55)
Page 88
Circuit Diagrams and PWB Layouts Q552.1E LA EN 88 LiteOn LED Common 2 LiteOn 15 LED Common 2 AL1B AL1B 2B50 C11 3B50 B7 +24V 3B51 B7 7B50-1 3B52 B7 BC847BS(COL) 3B53-1 B7 3B53-2 C7 3B53-3 C7 FB70 3B53-4 C7 PWM-B2 3B50 +24V...
Page 116
Circuit Diagrams and PWB Layouts Q552.1E LA EN 116 PNX Digital Video In PNX Digital Video In B02C B02C 2S2E F5 3S0W E5 7S00-6 D6 IS01 E6 IS10 E7 7S00-6 PNX85500 HDMI_DV HDMIA-RX2+ RX0_A HDMIA-RX2- HDMIA-RX1+ HDMIA-RX1- RX1_A DDCA-SCL DDC_A DDCA-SDA HDMIA-RX0+ IS10...
Need help?
Do you have a question about the 32PFL5405H/05 and is the answer not in the manual?
Questions and answers