Related Manuals for Sony VPH-V20M
Summary of Contents for Sony VPH-V20M
- Page 1 Color Video Projector Operating Instructions VPH-V20M/V20U VPH-V22M 1998 by Sony Corporation 3-865-079-11(2)
- Page 2 Table of contents...
- Page 3 Die geforderte Stückprüfung hat ergeben, daß die gemessene Ortsdosis-Leistung unter dem im Prüfungsschein Nr. 6.22-S1189 der PTB genannten Wert von 0,2 µSv/h liegt. Table of contents...
- Page 4 The socket-outlet should be installed near the equipment and be easily accessible. The instructions in this manual are for the VPH-V20U (for the USA and Canada) and the VPH-V20M/VPH-V22M (for European countries). Before you start operating, please check your model number.
-
Page 5: Table Of Contents
English Table of Contents Overview Projecting Installation/connection examples Other Precautions ... 6 Features ... 8 Location and Function of Controls ... 9 Control Panel... 9 Front (Connector Panel) ... 10 Remote Commander RM-PJV20 ... 11 Projecting ... 13 Adjusting the Picture ... 15 Displaying the Current Control Settings ... -
Page 6: Precautions
• When the projector is mounted on the ceiling, the Sony PSS-722/PSS-10 projector suspension support must be used for installation. Read the installation manual of the PSS-722/PSS-10 carefully, since the ceiling should be reinforced for safety. - Page 7 If the CRT burns, it must be replaced. In this case, refer to the warranty provided with this unit. Consult your Sony dealer or Qualified Service Personnel. Save the original shipping carton and packing material; they will come in handy if you ever have to ship your unit.
-
Page 8: Features
Features Bright image—light output of 750 lumen Clear color reproduction—high-quality circuit Component signal input Wireless and wired remote control Illuminated remote commander and control panel Other features Overview A newly developed phosphor and electron gun provide a high-quality image with extra sharpness and brightness. A high-quality picture is obtained by combining the use of a three-line logical comb filter to reduce dot interference and cross color, and the use of a new chroma transient circuit to improve color sharpness by removing... -
Page 9: Location And Function Of Controls
Location and Function of Controls Control Panel Open the control panel cover. B CENT R CENT !¡ !º 1 POWER switch Press to turn the projector on and off. 2 INPUT SELECT buttons Press to select the input signal. VIDEO connector (BNC): to select the signal input from the VIDEO IN VIDEO connectors S VIDEO connector (4-pin mini DIN): to select the signal input from the VIDEO IN S VIDEO connectors... -
Page 10: Front (Connector Panel)
Connect to the video input of a color monitor. 6 CONTROL S jacks INPUT (stereo minijack): Connect to the CONTROL S OUTPUT jack of other Sony equipment. If you connect to the CONTROL S OUT jack of the supplied remote commander with the remote... -
Page 11: Remote Commander Rm-Pjv20
Remote Commander RM-PJV20 1 LIGHT button Press to light the button indicators. To turn off the light, press it again while they are lit. If you do not operate any button within about 30 seconds, the light automatically turns off. 2 Transmitter indicator The light turns on each time a button is pressed. - Page 12 Location and Function of Controls Battery installation Push and slide to open the lid. Install three R6 (AA) batteries with the correct polarity. Replace the lid. Notes • If the projector does not operate properly, the batteries might be worn out. Replace all three of them with new batteries.
-
Page 13: Projecting
Projecting You can also use the buttons on the control panel with the same names as those on the remote commander to operate the projector. MUTING VIDEO S VIDEO RESET TEST R CENT B CENT Press down the MAIN POWER switch of the projector (O ON). Turn on the power by pressing the 1/u (power on/standby) button. - Page 14 Projecting To turn off the power To switch the aspect ratio To cut off the picture If the picture rolls vertically To adjust the horizontal position of the RGB input picture Projecting To turn off the projector Press the 1/u button or the MAIN POWER switch on the projector. If the projector is turned off with the MAIN POWER switch, the projector is turned on again only by the MAIN POWER switch.
-
Page 15: Adjusting The Picture
Adjusting the Picture Three adjustment level patterns for the video and component input pictures and one pattern for the RGB input picture, respectively, are stored in the projector’s memory. You can recall them by pressing the M SEL button. Press the M SEL button to select the memory position 1, 2 or 3. -
Page 16: Displaying The Current Control Settings
Projecting Displaying the Current Control Settings Press the PAGE button to display the following on-screen displays. You can change various settings on these displays. Each time you press the PAGE button, the display switches as follows: USER PRESET n PICTURE CONTROL n SYSTEM PRESET. - Page 17 SYSTEM PRESET D PICTURE ON: to enhance the contrast, providing a dynamic image. OFF: to display a dark portion faithfully according to the video source. Y DELAY Luminance and chroma (color) signals may be transmitted with a slight time lag depending on the video equipment.
-
Page 18: Centering Adjustment
Centering Adjustment Projecting The three colors, red, green and blue, must converge for proper projection. If you move the projector to another location, you have to perform the centering adjustment. The following are the procedures for using a built-in test pattern. You can also perform the centering adjustment using an external test signal without displaying a test pattern. - Page 19 To check the current centering condition Press the arrow buttons to move the horizontal and vertical red lines until they converge with the center green lines and are seen as yellow. The red lines move according to the direction of the arrow. blue H: Horizontal adjustment level (MIN, –126 –...
-
Page 20: Installation Diagrams
873 (34 1,006 (39 1,214 (47 1,414 (55 1,544 (60 1,884 (74 * Sony screen VPS-100FH ** Sony screen VPS-120FH “A” and “B” correspond to those in the illustration below. Center of the green lens Floor Tolerance in length: ±1%... -
Page 21: Flat Screen
813 (32 824 (32 879 (34 1,012 (39 1,145 (45 1,350 (53 1,550 (61 1,680 (66 2,020 (79 * Sony screen VPS-100FH ** Sony screen VPS-120FH PSS-722 Ceiling Tolerance in length: ±1% 2,614 (103) 2,692 (106) 2,932 (114 3,552 (139... -
Page 22: Installation 3 Floor Installation Using Rear Projection
1,067 (42 1,524 (60 Installation/connection examples “B” and “C” correspond to those in the illustration below. Unit: mm (inches) 690 (27 889 (35) * Sony screen VPS-702R Wall Center of the screen Floor Tolerance in length: ±1% 2,363 (93 3,301 (130) -
Page 23: Installation 4 Ceiling Installation Using Rear Projection
PSS-722 (not supplied) VPS-702R universal rear screen Screen size (inches) 1,067 (42 1,524 (60 PSS-722 Unit: mm (inches) 674 (26 873 (34 * Sony screen VPS-702R Ceiling Center of the screen Wall Tolerance in length: ±1% 2,614 (103) 3,552 (139 Installation/connection examples... -
Page 24: Installation 5 Level Projection, Floor Installation
1,524 (60 Installation/connection examples Unit: mm (inches) 165 (6 676 (26 167 (6 715 (28 * Sony screen VPS-702R “B” and “C” correspond to those in the illustration below. Wall Center of the screen Floor Tolerance in length: ±1% Angle ( ) -
Page 25: Installation 6 Level Projection, Ceiling Installation
Center of the screen Unit: mm (inches) 165 (6 676 (26 167 (6 715 (28 * Sony screen VPS-702R Center of the screen “B” and “C” correspond to those in the illustration above. Tolerance in length: ±1% Angle ( ) -
Page 26: System Connections
System Connections Installation Diagrams Connecting to the Projector 4-pin, mini DIN to VIDEO IN S VIDEO VCR equipped with S VIDEO connector Sony Betacam video camera, DVD to C /R-Y/Y/C /B-Y component signal output Installation/connection examples Notes on connections • First make sure that the power to each piece of equipment is turned off. -
Page 27: List Of The Messages
List of the Messages Use the list below to check the meaning of the messages displayed on the screen. The list is divided into sections according to the location where the message appears. Check the location first, then refer to the corresponding letter for the section to find the message. - Page 28 List of the Messages Other SYSTEM PRESET D PICTURE: ON/OFF The Dynamic picture feature functions or not. Y DELAY: +/ –/STD Color shifts left or right, or does not shift. CENT ADJ: EXT, INT Centering adjustment is performed with an external test signal or a built-in cross-hair test pattern.
-
Page 29: Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem using the following guide. If the problem still persists, consult with qualified Sony personnel. The power does not turn on. • The MAIN POWER switch is turned off. -
Page 30: Specifications
Approx. 532 288 597 mm (w/h/d) signal (Y) With the brackets pushed down, including the projection parts and Ground controls Mass VPH-V20M/V20U: Approx. 30 kg (66 lb 2 oz) VPH-V22M: Approx. 38 kg (83 lb 12 oz) /R-Y, C /B-Y: BNC connectors inches) - Page 31 Accessories supplied Remote commander RM-PJV20 with 3 AA (R6) batteries AC power cord (1) Spacer for 200" front projection (4) 0.2 mm spacer t for 70" to 100" (9) 0.8 mm spacer s for 70" to 100" rear projection (3) Design and specifications are subject to change without notice.
- Page 32 Sony Corporation Printed in Japan...
Need help?
Do you have a question about the VPH-V20M and is the answer not in the manual?
Questions and answers