Advertisement
Quick Links
Download this manual
See also:
User Manual
Quick Start Guide
TCC300 Tapchanger Control
1
LCD SCREEN
2
EXIT/WAKE
Push button
3
VR Pushbutton
Shortcuts/arrows
4
SETP
5
MNTR
6
ENT/UTL Push button
7
CNFG
8
COMM
9
LEDS
10
USB Port
11
Smart FlashCard Slot
1
9
10
11
2
Pressing any push button will wake up the LCD and display the heading corresponding to the "Hot Button" label
inside the push button - WAKE, MNTR, SETP, CNFG, COMM, UTIL, or VR.
The EXIT WAKE Push button wakes the LCD from sleep mode and begins scrolling through a list of user pro-
grammed metered/calculated values.
Activates the user defined Voltage Reduction Steps
Access to the Setpoints screens
Access to the Monitoring screens
Access to the Utilities screens and enter button
Access to the Configuration screens
Access to the Communication screens
See page 2
Out of Band High Voltage
Used for loading and saving setpoints, DNP files and IEC 61850 CID files, saving datalog, SOE and OSC files, clone
saving and uploading, updating firmware, saving Wakeup screen parameters and all metering parameters, and can
be used as an Access Code Key.
4
6
5
8
3
7
Advertisement
Related Manuals for ABB TCC300
Summary of Contents for ABB TCC300
- Page 1 Quick Start Guide TCC300 Tapchanger Control LCD SCREEN Pressing any push button will wake up the LCD and display the heading corresponding to the “Hot Button” label inside the push button - WAKE, MNTR, SETP, CNFG, COMM, UTIL, or VR.
- Page 2 Optic (optional) Current Loop Module Connector (optional) BlueTooth RS-485 RJ-45 Ethernet over RS-232 DE9S Fiber Optic 24-Pin Blue Connector for Source Voltage Input Copper (optional) ST Connector TCC300 Adapter Panels or One Aux Output Front Direct Connection Three Aux Inputs...
- Page 3 2. The customer is to provide an earth ground connection to the CT/VT‘s neutral connection, external to the control 3. To Motor Power Seal-in board. 4. If the TCC300 is configured for the SCAMP push button Auto/Manual Switch type, the Self-Test Alarm relay is NOT avai- lable.
-
Page 4: Safety Information
Safety information Death or severe electrical shock can occur In no case should the line current circuit be interrupted with the regulator or transformer energized. Do not remove auxiliary current transformers without shorting the current inputs. Exercise care during installation, operation and maintenance procedures The equipment described in this manual contains voltages high enough to cause serious injury or death. -
Page 5: Menu Screens
Menu screens Press EXIT to go to the Menu Header. Press either ← or → to move sideways to the adjacent Menu Header. UTILITIES MONITOR COMM MNTR UTIL SETP Harmonics Tap Information Metering Present Demand Demand History Energy Metering Watt Hours Fwd Tap Position/Cal Load Voltage Load Voltage... - Page 6 Menu screens SETPOINTS CONFIGURATION COMMUNICATION MNTR CNFG CNFG UTIL SETP COMM Active Setpoint Profile or Setpoint Profile Selected for Editing VAr Bias Profile Settings Common Settings 1 Power Flow Fwd 1 Power Flow Reverse 1 Active Profile LDC Selection Bandcenter Fwd Bandcenter Rev Profile :1 xxx.x Volts...
- Page 7 Menu screens CONFIGURATION CONFIGURATION CONFIGURATION CONFIGURATION CONFIGURATION SETP COMM SETP COMM SETP COMM SETP COMM SETP COMM To Data Logging Nameplate Run Through Neutral Remote Voltage Bias Tapchanger Type Tap Settings CT Multiplier Enable/Disable Enable/Disable Tapchanger Type Tap Position/Cal 6000 X disable disable DISABLE...
- Page 8 Menu screens Paralleling Programmable Alarm System Clock Paralleling Type Paralleling Type Prog Alarm Function Set Date and Time DISABLE DISABLE –<0000000000000000 08/26/13 15:41:29 Auto/Man Switch Type set to SCAMP Paralleling Type Paralleling Type Paralleling Type Paralleling Type Daylight Savings MASTER/FOLLOWER DELTA VAR #1 PEER2PEER DELTAVAR DELTA VAR #2...
- Page 9 115200 RS232 Press ENT to begin Net Mask User Line 2E Bluetooth Protocol Parity Comm Protocol Save Datalog 0.0.0.0 TCC300 MODBUS NONE DNP3.0 Press ENT to begin Gateway Level 1 Access Code Authentication Stop Bits DNP Configuration Save seq. of events 0.0.0.0...
- Page 10 Press ENT to begin 8192 X X1 Duration Mtr Sin Coefficient 0 ms, Avg: 0 ms Alarm Activity Mtr Cos Coefficient Press ENT to Begin 8192 X Complete customer documentation is available in the product pages that can be accessed through www.abb.com...
- Page 12 Contact us ABB Inc. EPMV Distribution Automation 4300 Coral Ridge Drive Coral Springs, FL 33065, USA Phone +1 (800) 523-2620 Phone +1 954-752-6700 Fax +1 954 345-5329 www.abb.com/substationautomation...
Need help?
Do you have a question about the TCC300 and is the answer not in the manual?
Questions and answers