Related Manuals for Philips MC157/61
Summary of Contents for Philips MC157/61
- Page 1 MC157 Micro Hi-Fi System Register your product and get support at www.philips.com/welcome User manual...
- Page 3 CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
- Page 4 Index English ------------------------------------------------ 6...
-
Page 5: Table Of Contents
Contents General Information Supplied accessories ... 7 Environmental Information ... 7 Safety Information ... 7 Hearing Safety ... 8 Preparations Rear connections ... 9 Inserting batteries into the Remote Control ..10 Using the Remote Control to operate the system ... -
Page 6: General Information
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Supplied accessories – 2 speaker boxes – remote control Environmental Information All unnecessary packaging has been omitted. We... -
Page 7: Hearing Safety
General Information Hearing Safety Listen at a moderate volume. ● Using headphones at a high volume can impair your hearing. This product can produce sounds in decibel ranges that may cause hearing loss for a normal person, even for exposure less than a minute. -
Page 8: Preparations
FM wire antenna speaker (right) Rear connections The type plate is located at the rear of the system. Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. WARNING! – For optimal performance, use only the original power cable. -
Page 9: Inserting Batteries Into The Remote Control
Preparations Inserting batteries into the Remote Control Open the battery compartment. Insert two R03 or AAA batteries following the indications (+/-) inside the compartment. Close the cover. Using the Remote Control to operate the system Aim the Remote Control directly at the remote sensor (IR) on the front panel. -
Page 10: Controls Available On The Remote Control Only
Controls on the system and remote control STANDBY-ON2 (POWER) – switches the system to standby or on. iR SENSOR – infrared sensor for remote control. SOURCE – selects the respective sound source for CD/ TUNER/TAPE/AUX. – switches on the system. PRESET +/- for radio ... -
Page 11: Basic Functions
Basic Functions IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY -ON 2 or SOURCE (POWER on the remote control). ➜ The system will switch to the last selected source. ● Press DISC, TUN, TAPE or AUX on the remote control. -
Page 12: Cd Operation
STANDBY-ON M I C RO S Y S T E M M C 1 7 CD/CD - R/CD - RW COMPATIBLE SOURCE TUNING PRESET IMPORTANT: The lens of the CD player should never be touched. Loading a disc This CD player plays Audio Discs including CD- Recordables and CD-Rewritables. -
Page 13: Different Play Modes: Shuffle And Repeat
CD Operation Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback. The play modes cannot be combined with PROGRAMME. SHUF ... tracks of the entire disc are played in random order. REP ALL ... -
Page 14: Radio Reception
Tuning to radio stations Press SOURCE on the set repeatedly or press TUN on the remote control repeatedly until the desired waveband (FM or MW) is displayed. Press down on TUNING 4 ¢ (à / á on the remote control) and release the button. ➜... -
Page 15: Tape Operation / Recording
Tape Operation / Recording Tape playback Select TAPE source. ➜ Display: shows “tAPE” throughout tape operation. Open the tape key flap marked “PULL TO OPEN” on the front panel. Press STOP•OPENÇ0 to open the tape door. Insert a recorded tape and close the tape door. ●... -
Page 16: Recording From The Radio
Tape Operation / Recording Recording from the radio Tune to the desired radio station (see Tuning to radio stations). Press STOP•OPENÇ0 to open the tape door. Insert a suitable tape into the deck and close the tape door. Press RECORD● to start recording. To interrupt playback press PAUSE;. -
Page 17: Maintenance
Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner. -
Page 18: Clock/Timer
Setting the clock In standby mode, press and hold CLOCK/ DISPLAY on the remote control set for 2 seconds. Press PROG to select 12-hour or 24-hour display. Press CLOCK/DISPLAY to confirm. ➜ The clock digits for the hours flash. Press TUNING 4 ¢ (à / á on the remote control) to set the hours. -
Page 19: Specifications
Specifications AMPLIFIER Output power ... 2 x 2W RMS Signal-to-noise ratio ... ≥ 60 dBA (IEC) Frequency response ... 125 – 16000 Hz Impedance loudspeakers ... 8Ω CD PLAYER Frequency range ... 125 – 16000 Hz Signal-to-noise ratio ... 65 dBA TUNER FM wave range ... -
Page 20: Troubleshooting
Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or Philips for help. -
Page 21: Troubleshooting
Troubleshooting Problem The remote control does not function properly. The time is not working. The Clock/Timer setting is erased. Solution ✔ Select the source (CD or TUNER, for example) before pressing the function button (É,í,ë). ✔ Reduce the distance between the remote control and the system. - Page 22 Meet Philips at the Internet http://www.philips.com CLASS 1 LASER PRODUCT MC157_61_UM_V3.0...
Need help?
Do you have a question about the MC157/61 and is the answer not in the manual?
Questions and answers