Related Manuals for Philips MCM108B/98
Summary of Contents for Philips MCM108B/98
- Page 1 Micro Hi-Fi System Register your product and get support at www.philips.com/welcome. MCM108 MCM108B MCM108C...
- Page 2 STANDBY-ON SOURCE BAND PROG/CLOCK VOLUME M I C R O S Y S T E M 1 0 8 TUNING AUX - IN...
-
Page 3: General Information
PLEASE NOTE THAT THE VOLTAGE remote control To fully benefi t from the support that SELECTOR LOCATED AT THE REAR OF Philips offers, register your product at THIS SYSTEM IS PRESET AT 220V FROM BAND www.philips.welcome.com THE FACTORY. FOR COUNTRIES THAT –... - Page 4 General Information English IMPORTANT! Controls on the system and PLEASE NOTE THAT THE VOLTAGE remote control SELECTOR LOCATED AT THE REAR OF THIS SYSTEM IS PRESET AT 220V FROM BAND THE FACTORY. FOR COUNTRIES THAT – for Tuner (on the set only) selects waveband. OPERATE AT 110V-127V, PLEASE ADJUST SOURCE (CD/ TUNER/ AUX) TO 110V-127V BEFORE YOU SWITCH ON...
-
Page 5: Rear Connections
Preparations Speaker (right) Rear connections The type plate is located at the rear of the system. A A A A A Power – Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. –... -
Page 6: Before Using The Remote Control
Preparations Speakers Connection Front Speakers Connect the speaker wires to the SPEAKERS terminals, right speaker to "RIGHT" and left speaker to "LEFT", the wire (marked red) to "+" and the wire (marked black) to "-". ● Fully insert the stripped portion of the speaker wire into the terminal as shown. -
Page 7: Basic Functions
Basic Functions STANDBY-ON SOURCE BAND PROG/CLOCK IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY -ON (y on the remote control). ➜ The system will switch to the last selected source. ● Press SOURCE (CD, TUNER or AUX on the remote control). -
Page 8: Basic Playback Controls
CD/MP3 Operation M I C R O S Y S T E M M C M 1 0 8 PROG IMPORTANT: The lens of the CD player should never be touched. Loading a disc This CD player plays Audio Discs including CD- Recordables, CD-Rewritables and MP3 CD. -
Page 9: Programming Track Numbers
CD/MP3 Operation Press ¡1 2™ to select a desired track. ➜ The album number will change accordingly as you reach the first track of an album by pressing ¡1 or the last track of an album by pressing 2™ . Press 2;... -
Page 10: Radio Reception
Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner. -
Page 11: Setting The Clock
Clock/Timer M I C R O S Y S T E M 1 0 8 Setting the clock In Standby mode, press PROG/CLOCK button. ➜ The clock digits for the hours flash. Press ¡1 / 2™ to set the hours. Press PROG/CLOCK again. -
Page 12: Troubleshooting
Troubleshooting WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre. -
Page 13: Specifications
Specifications AMPLIFIER Output power ... 2 x 2W RMS ... 200W PMPO Signal-to-noise ratio ... Frequency response ... 60 – 16000 Hz, ± 3 dB Impedance loudspeakers ... 8 Impedance headphones ... 32 CD PLAYER Frequency range ... 20 – 20000 Hz Signal-to-noise ratio ... -
Page 14: Class 1 Laser Product
Meet Philips at the Internet http://www.philips.com MCM108 MCM108B MCM108C CLASS 1 LASER PRODUCT PDCC-JH/ZC-0744 Printed in China PDCC-JH/ZC-0744 PDCC-JH-0628...
Need help?
Do you have a question about the MCM108B/98 and is the answer not in the manual?
Questions and answers