Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Product information is subject to change without notice. For detailed procuct information,please visit 50PUG6102 • without TV stand: www.philips.com/support Width 1129.54 mm - Height 656.45 mm - Depth 83.17 mm - Weight ± 12.80 kg Display • with TV stand: Width 1129.54 mm - Height 717.72 mm - Depth...
Page 4
• You can use any DLNA V1.5 certified media server • Wi-Fi 802.11b/g/n (built-in) software (DMS class). • You can use the Philips TV Remote app (iOS and Supported USB file systems • FAT 16, FAT 32, NTFS Android) on mobile devices.
3.2 Assembly/Panel Removal 3.2.1 Stand removal for 6102 serial 1. Remove the fixation screws [1] that secure the stand 2. Take the stand bracket out from the set. Stand removal for 6412 serial 1. Remove the fixation screws [1] that secure the stand 2.
Page 9
3.2.3 Keyboard Control Unit Remove all the fixation screws from the keyboard control panel [1] and take it out from the Back cover When defective, replace the whole unit. Release the connector [2] from the SSB Board. Caution: be careful, the Keyboard is catch on the Back cover, please be careful to avoid damage the fragile connectors! 3.2.4 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembly.
Page 10
1. Release the clips from the LVDS connector that connect with the SSB[1]. Caution: be careful, as these are very fragile connectors! 1. Unplug all other connectors [2] . 3. Remove all the fixation screws from the SSB [3]. 4. The SSB can now be shifted from side connector cover, then lifted and taken out of the I/O bracket. 4.
Page 11
3.2.8 WIFI module 1. Unplug the connector from the SSB.. 2. Remove fixation screw that secure the WIFI module, When defective, replace the whole unit. 3.2.9 LCD Panel 1. Remove the SSB as described earlier. 2. Remove the PSU as described earlier. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 13
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 14
After entering the Factory mode, we can see many items displayed, use the UP/DOWN keys to display the next/previous menu items Factory mode overview How to Exit the Factory mode Use one of the following methods: Select EXIT_FACTORY from the menu and press the “OK” button. Note: When the TV is switched “off”...
Page 15
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. Press the POWER button on the remote control transmitter.
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). 4. Switch off the TV and Insert the USB memory stick that contains the software update files in one of the TV’s USB 2.0 ports. Note: It contains USB3.0 port, if connect on it, the software may can’t be detected.
Page 17
Step 2: F/W Upgrade 1. Press [Quick settings], then Choose [Update Software] in the Settings menu 2. Choose [Local Updates], then press OK. Select the file that you downloaded and press OK 4. Choose [Update], then choose [Start] on following step...
Page 18
5. Upgrade in progress Step 3: Check the SW version 1. After burning software, TV will restart 2. Press “Menu+1999+back”, enter Factory mode to check if the software version is correct Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 19
5.2.2 How to Read the Error Buffer You can read the error buffer in three ways: • On screen via the SAM/CSM (if you have a picture). Example: – ERROR: 000 000 000 000 000: No errors detected – ERROR: 013 000 000 000 000: Error code 13 is the last and only detected error –...
Page 20
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT BOM# Panel Type 43PUG6102/77 TPT430U3-EQYSHM.G S1AE 43PUG6102/78 TPT430U3-EQYSHM.G S1AE 50PUG6102/77 TPT500U1-EQYSKM.G S1A...
6. Circuit Descriptions 6.1 Introduction The TPM17.9L LA is a new chassis launched in LATAM in 2017. The whole range is covered by MT5596LGEJ HSFBGA-757 platform. The major deltas versus its predecessor support NTSC;PAL-M; PAL-N AND ISDB-T with also multi-media, CEC,ARC, SPDIF functionality. The TPM17.9L LA chassis comes with the following stylings: ...
Page 22
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 23
• LED backlight: - side-view LED without scanning: PSL power panel - side-view LED with scanning: PSLS power panel - direct-view LED without 2D-dimming: PSL power panel - direct-view LED with 2D-dimming: PSDL power panel. PSL stands for Power Supply with integrated LED-drivers. PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller).
Page 24
6.3.2 Power layout SSB L801, VCC 1.8V_FRC U707,3V3SB C706,+5V_SW D703, +5V_STB C714,AVDD1V0_1 L703,VCCK Power SSB Top View...
Page 25
6.4 Front-End Analogue and DVB-T, DVB-C;ISDB-T reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER LATAM TDSY-H480F • SCALER MT5596LGEJ HSFBGA-757 Below find a block diagram of the front-end application for DVB-C part. TDSY-H480F MT5596LGEJ 6.5 HDMI...
Page 26
• CEC control • ARC control • MHL control 6.6 Video and Audio Processing - MT5596LGEJ The MT5596LGEJ is the main audio and video processor (or System-on-Chip) for this platform. It has the following features: • Worldwide multi-standard analog TV demodulator •...
8.7 E 715G7088 Keyboard control panel 8-7-1 CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Center 2-5 short Menu CN01 Right 1-5 short 0.5V KEY 1 AMBI_SPI_CLK Left 4-5 short 0.81V AMBI_SPI_MOSI 0.1uF 50V +12V_AMBI Down 3-5 short VOL- 1.65V +12V_AMBI...
8.8 J 715G8555 Keyboard control panel 8-8-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY 1 AMBI_SPI_CLK Left...
Need help?
Do you have a question about the 43PUG6102/77 and is the answer not in the manual?
Questions and answers