Philips led tv 22pfl3405 56 cm (22") hd ready with digital crystal clear (12 pages)
Summary of Contents for Philips 22PFS5304/60
Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 2
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Page 3
Product information is subject to change without notice. detailed product information, please visit For 24PHx43x4 www.philips.com/support TV Rear - HDMI 1 ARC: HDMI Audio Return Channel - HDMI 2 Display Input Resolution - DIGITAL AUDIO OUT: SPDIF - VGA For PHx series TV - AUDIO IN (DVI/VGA): Stereo 3.5mm mini-jack...
Page 4
mode, LNB current 300mA max * Only for DVB-T2, DVB-S2 Display Type Diagonal screen size Sound • 55 cm / 22 inch • • 60 cm / 24 inch Output power (RMS) : • 80 cm / 32 inch 24” series: 6W •...
Page 5
4. Switch “off” the set, and remove the wire between the to the diversity tables for the correct values. • The correct component values are listed on the Philips two pins of the Mains/AC Power plug. • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 6
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 7
• Always respect voltages. While some may not be originating from the USA and used e.g. in dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 8
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 9
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 10
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 × 768 (15:9) TXT-DW Dual Window with TeleteXT XTAL...
Page 14
3.2 Assembly/Panel Removal 3.2.1 Stand removal Notes: Figures below can deviate slightly from the actual situation due to the different set executions. Remove the fixation screws [1] that secure the stand. Take the stand bracket out from the set. (22"/24" series) (32"&43"...
Page 16
32” 4503, 43/50” 5503 Series: Remove all fixation screws [2] and [3] that secure the Back cover assy. Unplug the connector [2] that marked by red box below from SSB. Gently lift the rear cover from the TV. Make sure that wires and cables are not damaged while lifting the rear cover from the set. (32"&43"...
Page 17
32” 4503/4504, 43” 5503 Series: Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! Remove all the fixation screws [1] and connector [2] from the IR board control unit. Remove the IR lens, IR board from the DECO_REAR_COVER. When defective, replace the whole unit.
Page 18
3.2.5 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. Gently unplug all connectors from the PSU. Remove all fixation screws from the PSU. The PSU can be taken out of the set now.
Page 19
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 20
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 21
4.3 Factory mode: Purpose To perform extended alignments. Specifications Displaying and or changing Panel ID information. Displaying and or changing Tuner ID information. Error buffer clearing. Various software alignment settings. Testpattern displaying. Public Broadcasting Service password Reset. ...
Page 22
(32"&43" series) How to Exit the Factory mode Use one of the following methods: Select EXIT_FACTORY from the menu and press the “OK” button. Note: When the TV is switched “off” by a power interrupt, or normal switch to “stand-by” while in the factory mode, the TV will show up in “normal operation mode”...
Page 23
CSM Overview How to Navigate By means of the “CURSOR-DOWN/UP” knob (or the scroll wheel) on the RC-transmitter, can be navigated through the menus. How to Exit CSM To exit CSM, use one of the following methods. Press the MENU/HOME button on the remote control transmitter. ...
Page 24
5. Software Upgrading, Error code and Panel Code 5.1.1. The following update is for .pkg file. Rename the file to “upgrade_loader.pkg”. Prepare a USB memory (File format: FLAT, Size: 1G~8G). Copy the software to USB flash disk (root directory). Switch off the TV and Insert the USB memory stick that contains the software update files in one of the TV’s USB 2.0 port. Switch on the TV.
Page 25
Upgrade in progress. After software upgrade complete, select [Restart] to reboot TV. Step 3: Check the SW version After burning software, TV will restart. Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power!
Page 26
5.1 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every: • Activated (SW) protection. • Failing I2C device. • General I2C error. The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer. The error code buffer contains all errors detected since the last time the buffer was erased.
Page 27
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT BOM# Panel Type Display Code 22PFS5304/60 TPT215WF1-HVN01.U 102C 24PHS4304/12 TPM236WH2-WHBN00.K 5947 24PHS4304/12 TPM236WH2-WHBN00.K S5941C...
Page 28
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 29
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 30
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...
Page 32
7.2 Power Supply Power architecture of this platform: AUDIO LVDS Platform power Display power ON/OFF CN8605 for 715G7735P PS_ON Platform CN8602 12V_A MSD92L 5V_STB CN701 AC-input + Main filter AC IN 7.3 Power tree Power Board System Supply +12V_Normal/ 20.6W/ 1722mA Power Board Audio Supply +12V_Audio/ 10W/ 925mA Q701 +12V_Normal...
Need help?
Do you have a question about the 22PFS5304/60 and is the answer not in the manual?
Questions and answers