RF power Type TK-2170 K,K2,M TX/RX 136~174 Choose the type of transceiver TK-2170ST M A personal computer (IBM PC or compatible), programming Transceiver programming interface (KPG-22), and programming software (KPG-101D) are required for programming. (The frequency, TX power HI/LOW, and signaling data are programmed for the transceiver.)
TK-2170/2170ST REALIGNMENT 1. Modes 2. How to Enter Each Mode Mode Operation User mode User mode Power ON Panel test mode [A] + Power ON Panel test mode Panel tuning mode PC mode Received commands from PC Panel tuning mode [Panel test mode] + [S] PC mode Data programming mode...
Page 4
TK-2170/2170ST REALIGNMENT 5-2. Connection Procedure 6. Press write button in the window. When the transceiver starts to receive data, the “LOADING” is displayed. 1. Connect the transceiver to the personal computer with 7. If writing ends successfully, the checksum is calculated the interface cable.
Page 5
TK-2170/2170ST REALIGNMENT How to enter the password with the selector; If the selector is rotated while “CLN LOCK” is displayed, numbers (0 to 9) are displayed flashing. When you press the [C] key, the currently selected number is determined. If you press the [S] key after entering the password in this TX-RX UNIT (B/4) Foil side procedure, “CLONE”...
Page 6
TK-2170/2170ST REALIGNMENT ■ Channel edit mode 8-3. Zone/Channel Select Mode ■ To enable Zone/Channel select mode 1. Press the [A] key so that the “▼“ indicator is located on the right side, above the channel number. 1. Press the [Side2] key when “SELF” is displayed. The 2.
Page 7
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks DQT 023~754 Inverse D Q T 0 2 3 I _ (Standard Table Mode) D Q T 7 5 4 I _ D Q T 0 0 0 I ∗ DQT 000~777 Inverse D Q T 7 7 7 I ∗ (1 Step Mode) TX Frequency Step 2.5kHz...
Page 8
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks ←Default Wide/Narrow Wide W I D E _ _ _ _ Narrow N A R R OW _ _ ←Default Busy Channel Lockout B C L _ N O _ _ QT/DQT Tone B C L _ Q T _ _ Option Signaling B C L _ O P T _ Carrier Only...
Page 10
TK-2170/2170ST REALIGNMENT ■ Zone edit mode ■ Zone edit mode flow chart 1. Press the [A] key so that the “▼“ indicator is located on Self programming mode the left side, above the zone number. 2. Rotate the selector select your desired zone number. [Side2] 3.
Page 11
TK-2170/2170ST REALIGNMENT 8-4. Function Setting Mode 4. Press the [B] key to store the value in memory and ad- vance to the next setting. 1. Press the [Side1] key when “SELF” is displayed. The 5. Press the [C] key to skip any settings you do not wish to transceiver enters Function Setting Mode.
Page 12
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks Talk Around A U X _ _ 3 3 _ A U X _ _ 3 4 _ Zone Up A U X _ _ 3 5 _ Zone Down A U X _ _ 3 6 _ [S1] No Function S 1 _ _ O F F _...
Page 13
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks [S2] No Function S 2 _ _ O F F _ 2-tone S 2 _ _ _ _ 1 _ Autodial S 2 _ _ _ _ 2 _ S 2 _ _ _ _ 3 _ Optional Board=None Autodial Programming S 2 _ _ _ _ 4 _...
Page 14
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks Autodial Programming S _ _ _ _ _ 4 _ Call 1 S _ _ _ _ _ 5 _ Call 2 S _ _ _ _ _ 6 _ CH/GID Down S _ _ _ _ _ 7 _ CH/GID Up S _ _ _ _ _ 8 _ Channel Entry...
Page 15
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks CH/GID Up A _ _ _ _ _ 8 _ Channel Entry A _ _ _ _ _ 9 _ Direct CH1 A _ _ _ _ 1 0 _ Direct CH2 A _ _ _ _ 1 1 _ Direct CH3 A _ _ _ _ 1 2 _ Direct CH4...
Page 16
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks Direct CH3 B _ _ _ _ 1 2 _ Direct CH4 B _ _ _ _ 1 3 _ Display Character B _ _ _ _ 1 4 _ Home/CH/GID B _ _ _ _ 1 6 _ Key Lock B _ _ _ _ 1 7 _ Lamp...
Page 17
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks Key Lock C _ _ _ _ 1 7 _ Lamp C _ _ _ _ 1 8 _ ←Default Low Transmit Power C _ _ _ _ 1 9 _ Monitor C _ _ _ _ 2 0 _ Monitor Momentary C _ _ _ _ 2 1 _ C _ _ _ _ 2 2 _...
Page 18
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks DTMF (Autodial) K E Y O _ A T D DTMF (Keypad Auto PTT) K E Y O _ K A P FleetSync (SelCall) K E Y O _ S E L FleetSync (Status) K E Y O _ S T A FleetSync (SelCall+Status) K E Y O _ S / S...
Page 19
TK-2170/2170ST REALIGNMENT Function Choices Display Remarks First Digit Time 0, 100, 500, 1000 F D T _ _ _ _ 0 Default=0 ∗ and # Digit ∗ # _ _ _ _ _ 0 0, 100, 500, 1000 Default=0 Dial ID ON/OFF D I D _ O F F _ Default=OFF, Key=16key only...
TK-2170/2170ST DISASSEMBLY FOR REPAIR 1. Removing the FPC 3. How to Assemble the Antenna Connec- 1) Remove the solder from the TX-RX unit using a solder iron tor and its Terminal ( q ). The antenna connector and its terminal are supplied as 2) Peel the double-sided tape ( w ).
Page 22
TK-2170/2170ST DISASSEMBLY FOR REPAIR 4) Lift the speaker holder ( r ), then flip it over to the left 4. Replacing the Speaker and Microphone ( t ). 1) After affixing the double-sided tape (5.4 x 2.7 mm) to the 5) Insert the tabs of the speaker holder into the slots of the speaker, attach the speaker to the speaker holder ( q ).
TK-2170/2170ST CIRCUIT DESCRIPTION The filtered first IF signal is amplified by the first IF amplifier 1. Frequency Configuration (Q703) and then applied to the lF system IC (IC701). The IF The receiver utilizes double conversion. The first IF is system IC provides a second mixer, second local oscillator, 49.95MHz and the second IF is 450kHz.
Page 24
TK-2170/2170ST CIRCUIT DESCRIPTION 2-5. Audio Amplifier Circuit IC13 IC12 (1/2) IC13 (2/2) The demodulated signal from IC701 is amplified by IC10, AQUA-L and goes to AF amplifier through IC13. The signal then goes through an volume control (IC16), and is routed to an audio power amplifier (IC18) where it is MMUTE amplified and output to the speaker.
Page 25
TK-2170/2170ST CIRCUIT DESCRIPTION 4. Frequency Synthesizer Circuit 5. Control Circuit 4-1. Frequency Synthesizer The control circuit consists of microprocessor (IC7) and its peripheral circuits. It controls the TX-RX unit. IC7 mainly per- The frequency synthesizer consists of the TCXO (X501), forms the following;...
Page 26
TK-2170/2170ST CIRCUIT DESCRIPTION 5-3. Low Battery Warning 6. Signaling Circuit The battery voltage is monitored by the microprocessor 6-1. Encode (IC7 pin 123 : BATTLVL). When the battery voltage falls be- ■ Low-speed data (QT, DQT) low the voltage set by the Low Battery Warning adjustment Low-speed data is output from pin 30 of the CPU.
Page 27
TK-2170/2170ST CIRCUIT DESCRIPTION IC17 (1/2) BUFF IC13 TCXO AQUA-L IC16 IC12 IC14 EXTLIMIN HSDO RX Audio AF AMP RXAF LSDO Fig. 12 Encode 6-2. Decode 7. Power Supply ■ QT/DQT There are five 5V power supplies for the microprocessor: The output signal from IF IC (IC701) enters the micropro- 5M, 5MS, 5C, 5R and 5T.
TK-2170/2170ST SEMICONDUCTOR DATA Microprocessor : 30625MGP234HU (TX-RX unit IC7) Pin No. Port Name Function Pin No. Port Name Function KEY2 Key matrix 2 input RXD2/AINH RXD2 (COM1) KEY3 Key matrix 3 input AFDAT BB TDATA and DTRCLK TX APC adjust AFDIO BB DI/O HSDO...
Page 29
TK-2170/2170ST SEMICONDUCTOR DATA / COMPONENTS DESCRIPTION TX-RX unit (X57-7000-XX) Pin No. Port Name Function TCLK/DTRDO BB TCLK and DTRDO Ref. No. Use / Function Operation / Condition 5R control Voltage detector / INT KEY1O Key matrix output Voltage regulator / 5V KEY2O Key matrix output Voltage detector / RESET...
TK-2170/2170ST COMPONENTS DESCRIPTION Ref. No. Use / Function Operation / Condition Ref. No. Use / Function Operation / Condition Transistor AF amplifier DC supply control switch D12,13 10 key back light AF amplifier DC supply switch D14,16 Diode Radio state detector Q25,26 MIC ALC Diode...
TK-2170/2170ST PARTS LIST ✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Europe Les articles non mentionnes dans le Parts No. ne sont pas fournis. Y : AAFES (Europe) X : Australia M : Other Areas...
Page 32
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation CK73HB1H471K CHIP C 470PF C129 CK73GB1E105K CHIP C 1.0UF CK73GB1E105K CHIP C 1.0UF C130 CK73HB1A104K CHIP C 0.10UF CK73HB1A104K CHIP C...
Page 33
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C510 CK73HB1C223K CHIP C 0.022UF C611 CC73HCH1H470J CHIP C 47PF C511 CK73GB1E105K CHIP C 1.0UF C612 CK73HB1H102K CHIP C 1000PF...
Page 34
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C725 CK73HB1A104K CHIP C 0.10UF E11-0457-05 PHONE JACK (2.5/3.5) C726 CK73HB1C103K CHIP C 0.010UF C727 CK73HB1H102K CHIP C 1000PF F901...
Page 35
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation L717 L40-5675-57 SMALL FIXED INDUCTOR (56.0NH) R55,56 RK73HB1J474J CHIP R 470K 1/16W L901 L92-0149-05 CHIP FERRITE RK73HB1J103J CHIP R 1/16W...
Page 36
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R144 RK73HB1J472J CHIP R 4.7K 1/16W R229,230 RK73HB1J123J CHIP R 1/16W R145 RK73HB1J154J CHIP R 150K 1/16W R231 RK73HB1J103J...
Page 37
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R611 RK73HB1J393J CHIP R 1/16W R745 RK73HB1J104J CHIP R 100K 1/16W R612 RK73HB1J101J CHIP R 1/16W R748 RK73HB1J104J CHIP R...
Page 38
TK-2170/2170ST PARTS LIST TX-RX UNIT (X57-7000-XX) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation ✽ IC701 TA31136FNG MOS-IC UMG3N TRANSISTOR FP210 TRANSISTOR UPA672T UMG3N TRANSISTOR UPA672T DTA114EE DIGITAL TRANSISTOR SSM6J08FU(F) 2SC4617(S) TRANSISTOR 2SB1132(Q,R)
TK-2170/2170ST EXPLODED VIEW 701x2 RF UNT TX-RX unit (D/4) SHIELDING PLATE TX-RX unit (A/4) TX-RX unit (B/4) TX-RX unit (C/4) 707 : M : N09-2438-05 : N14-0583-04 : N14-0805-04 D M2.6 x 10 : N30-2610-48 705 : K M3 x 6 BLK : N30-3006-45 M2 x 3 : N79-2030-48 G M2 x 5...
TK-2170/2170ST ADJUSTMENT ■ Frequency and Signaling Controls The set has been adjusted for the frequencies shown in Selector Selector the following table. When required, readjust them following Volume Volume the adjustment procedure to obtain the frequencies you want in actual operation. •...
Page 42
TK-2170/2170ST ADJUSTMENT ■ 3 or 5 reference level adjustments frequency Panel Tuning Mode ■ Preparations for tuning the transceiver Tuning point RX (MHz) TX (MHz) Before attempting to tune the transceiver, connect the 136.05000 136.10000 unit to a suitable power supply. Low’...
Page 43
TK-2170/2170ST ADJUSTMENT ■ Flow chart 3 reference level Frequency adjustments 5 reference level High power adjustments 3 reference level Low power adjustments Center 3 reference level Balance Narrow adjustments [Side2] [Side2] Max deviation Narrow Max deviation Wide High 3 reference level adjustments 3 reference level adjustments exit...
Page 44
Refer to page 26 for details. nut, use a recommendation tool. KENWOOD part No. : W05-1123-00 Note : When using the battery jig, you must measure the voltage at the terminals of the battery jig. Otherwise, a slight...
Page 45
TK-2170/2170ST ADJUSTMENT Common Section Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 1. Setting 1) BATT terminal voltage : 7.5V 2) SSG standard modulation [Wide] MOD : 1kHz, DEV : 3kHz [Narrow] MOD : 1kHz, DEV : 1.5kHz ±...
Page 46
TK-2170/2170ST ADJUSTMENT Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 5. Low power [Panel test mode] Power meter Panel Check 0.7~1.4W check 1) CH-Sig : 1-1 Ammeter 1.0A or less Set low power (Push [S]) PTT : ON 2) CH-Sig : 2-1 PTT : ON 3) CH-Sig : 3-1...
Page 47
TK-2170/2170ST ADJUSTMENT Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment ± 40Hz 12. DQT 1) Adj item : [DQT_ _] Power meter Panel Panel Selector 0.35kHz deviation Adjust : [✳✳✳.] knob adjust Deviation meter filter Deviation SP/MIC LPF : 3kHz meter...
Page 48
TK-2170/2170ST ADJUSTMENT Receiver Section Measurement Adjustment Item Condition Specifications/Remarks Test- Unit Terminal Unit Parts Method equipment 1. Sensitivity 1) Adj item : [SENS_] Panel Panel Selector Adjust for Rotate the selector knob and adjust Adjust : [✳✳✳] knob RSSI MAX increase the adjustment value 2) Adj item : [S.ENS_] →...
TK-2170/2170ST TERMINAL FUNCTION ■ CN60 ■ Solder Point Connection Pin No. Pin Name I/O Function Designation Function Condiition / Value MIC_I MIC input Input sensitivity / impedance (1kHz std. dev.) Switched B output 500mVrms± 100mV, @22kΩ load DC (Battery terminal)± 0.5V, 150mA max MIC_O MIC output Output voltage / impedance...
Page 70
TK-2170/2170ST KSC-30 (RAPID CHARGER) External View Operating Flow Chart Power ON Initialization Insert battery Does S terminal connect? Parts List Vs : High Battery is not (Li-ion) Distinguish the Desti- correspond Ref. No. Parts No. Description kinds of battery parts nation LED OFF A02-3656-08...
13, Boulevard Ney, 75018 Paris, France Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Kwai Fong, N.T., Hong Kong KENWOOD House, Dwight Road, Watford, Herts., WD18 9EB United Kingdom 1 Ang Mo Kio Street 63, Singapore 569110...
Need help?
Do you have a question about the TK-2170ST and is the answer not in the manual?
Questions and answers