TANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, THESE COMPONENTS WITH SONY PARTS WHOSE PART NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
All manuals and user guides at all-guides.com . s l . s l . s l . s l e i l n i l i n i WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP rating.
All manuals and user guides at all-guides.com 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
All manuals and user guides at all-guides.com FE-2 SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
All manuals and user guides at all-guides.com SECTION 2 DISASSEMBLY 2-1. Rear Cover Removal => => => => Remove the rear cover fixing screws indicated and withdraw the rear cover from the Beznet. 2-2. Chassis Removal and Refitting When refitting the chassis ensure that the main bracket is located in the beznet guide slots before sliding the chassis forwards.
All manuals and user guides at all-guides.com 2-3. A Board Removal [ Step 1 ] 2-4. A Board Removal [ Step 2 ] Clip. Screw. Remove the 3 screws securing the PWB to the main bracket. Release the 5 securing clips located around the side of the 1 can be seen in the photo above and the other 2 are either chassis and slide the PWB clear of the bracket.
All manuals and user guides at all-guides.com 2-7. Picture Tube Removal WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap.
All manuals and user guides at all-guides.com SECTION 3 SET-UP ADJUSTMENTS • Carry out the adjustments in the following order : When complete readjustment is necessary or a new picture 3-1. Beam Landing. tube is installed, carry out the following adjustments. 3-2.
All manuals and user guides at all-guides.com If the V.STAT magnet is moved in the direction of the (a) 3-2. Convergence and (b) arrows, the Red, Green and Blue points move as indicated below. Preparation: • Before starting this adjustment, adjust the focus, horizontal size and vertical size.
Page 19
All manuals and user guides at all-guides.com Geometry Adjustment. YCH Adjustment Preparation: YCH VR 28" YCH VR 32" Before starting this adjustment, adjust the horizontal and vertical static convergence. Deflection Yoke Deflection Yoke Remove the deflection yoke spacer. Tilt the deflection yoke as indicated in the figure below and TLV Adjustment optimise the geometry.
All manuals and user guides at all-guides.com Layout of each control 3-4. Screen (G2), White Balance [Adjustment in the service mode using the remote commander] G2 adjustment Input a dot signal from the pattern generator. Set the Picture, Brightness and Colour to minimum. Apply 165V DC from an external power supply to the R, G V.STAT and B cathodes of the CRT.
All manuals and user guides at all-guides.com SECTION 4 CIRCUIT ADJUSTMENTS 4-1. Electrical Adjustments Service adjustments to this model can be performed using the supplied remote Commander RM-947. How to enter into the Service Mode Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander.
Page 22
All manuals and user guides at all-guides.com Deflection System Adjustment Sub Brightness Adjustment Set the TV set or operation in Service Mode [ See Page 21 ] Input a Monoscope pattern. and enter into the ‘Geometry’ service menu. Set the TV set or operation in Service Mode. [ See Page 21 ]. Select and adjust each item in order to obtain the optimum image.
All manuals and user guides at all-guides.com 4-2. TEST MODE 2: Test Mode 2 is available by programming the TV set for operation in Service Mode [ As shown on Page 21 ], OSD ‘TT’ appears. The functions described below are available by selecting the two numbers. To release the ‘Test mode 2’, press 00, 10, 20 ... twice or switch the TV set into Stand-by mode.
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (1) CN707 CN8801 T3602 SMART LINE FILTER LIGHTNING 200V FUSE R.G.B. OUT CN3601 TO A BOARD (2/2) CN3603 F3601 CN508 AC IN AC OUT MOSFET SWITCH F5 BOARD CN706 Q8801 SWITCH AC IN AC OUT...
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (2) CN1201 R AUDIO TO SPEAKERS L AUDIO CN1200 HP PLUGGED IC1201 AUDIO AMP R OUT OUT/R R IN TO H6 BOARD IN/INL CN4502 MUTE SW L OUT LOW B MUTE OUT/L Q212...
All manuals and user guides at all-guides.com 5-1. BLOCK DIAGRAMS (3) A 2/2 ( POWER SUPPLY, DEFLECTION, VIDEO, AUDIO IC501 CN605 V OUTPUT PH601 ISOLATOR CN501 LOW B V- DY+ BOOST MAIN RECT CN606 D601 V- DY- AC IN RELAY RY601 H- DY- F5 BOARD...
All manuals and user guides at all-guides.com ~ A Board IC Voltage Table~ ~ A Board Difference Table 1~ ~ A Board Waveforms ~ 5-2. CIRCUIT BOARD LOCATION Reference Information RESISTOR : METAL FILM 20us/div 20us/div : SOLID C Board FPRD : NON FLAMMABLE CARBON FUSE...
All manuals and user guides at all-guides.com ~ A Board Semiconductor Location Table ~ NOTE: Portions of the circuit marked as shown are high voltage areas. Use care to prevent electric shock during inspection or repair. ~ A Printed Wiring Board Conductor side ~ - 28 -...
All manuals and user guides at all-guides.com A..-28/32HX15 POWER SUPPLY R603 C621 470p 1/2W 500V JW643 D601 FB602 R613 D4SB60L-F C603 8.2M 1.1uH T603 1000p C613 D639 R608 R611 250V JW644 1500p CN606 2.7k L603 PS1201 1/10W 1/10W C428 6.8uH AUDIO_VCC JW645 R606...
Page 30
All manuals and user guides at all-guides.com A..-28/32HX15 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL JR505 CN512 CHIP R045 IC501 STV9379 1/10W V OUTPUT L504 SMART C516 TP10 H.DY- 1200V C582 JR508 CHIP R589 1200V R588 D502 R564 R542 C503...
Page 31
All manuals and user guides at all-guides.com SERVICE CN001 TU101 CN301 MONO CN102 CN101 TUNER+IF A..-28/32HX15 STEREO C106 C105 0.01 L101 JW217 L104 56uH JW411 22.5MM 4.7uH J404 VIDEO 7.5MM JW218 L103 C101 C112 JR114 L102 22.5MM R100 JW409 17.5 4.7uH 0.01 C100...
Page 32
All manuals and user guides at all-guides.com TO H6 BOARD CN4502 A..-28/32HX15 CN1201 CN1200 CN1202 J1200 IC1201 C1225 TDA7495S AUDIO AMP R1202 R1217 JW1232 XX JW1227 XX 1/10W JW1209 4/4 AUDIO & VIDEO JW1216 XX C1203 JW1217 C1227 C1204 XX C1200 C1232 JW1220...
All manuals and user guides at all-guides.com F3.-28/32HX51 F5.-28/32HX15 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL LIGHTNING DISCHARGE, FUSE, LINE FILTERS CN6102 S6100 CN6100 F001 AC OUT TO A BOARD AC IN TO F3 BOARD CN606 CN3603 AC OUT AC IN T3604...
All manuals and user guides at all-guides.com ~ H6 Printed Wiring Board Conductor Side ~ ~ F3 Printed Wiring Board Conductor Side ~ ~ F5 Printed Wiring Board Conductor Side ~ - 34 -...
All manuals and user guides at all-guides.com ~ D2 Printed Wiring Board Conductor Side~ ~ C Printed Wiring Board Conductor Side ~ ~ VM Printed Wiring Board Conductor Side~ - 36 -...
All manuals and user guides at all-guides.com 5-5. IC BLOCK DIAGRAMS A BOARD IC501 STV9379A A BOARD IC401/IC531 LM393DT FLYBACK GENERATOR POWER AMPLIFIER THERMAL PROTECTION A BOARD IC601 MCZ3001D Remote DVLD Internal Driver Sel=34v ref 5v Reg. 10v 15v/8v Level Shift Vsense Control...
All manuals and user guides at all-guides.com SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for routine service.
All manuals and user guides at all-guides.com SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page A BOARD COMMON Parts List : Parts common to all models listed in this manual ...... 44 Model Parts that belong only to the model specified KV-28HX15 ....................
Page 44
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1059-323-A A Board Complete KV-28HX15B C112 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% 25V * A-1066-097-A A Board Complete KV-28HX15E C204 1-115-340-11 CERAMIC CHIP 0.22UF 10.00% 25V * A-1066-084-A A Board Complete KV-28HX15U C211 1-162-970-11...
Page 55
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK VM Board Variant Parts 28HX15 < FERRITE BEAD > < CAPACITOR > FB1701 1-535-303-00 LEAD, JUMPER (5.0MM) C1732 1-216-295-91 SHORT CHIP < COILS > C1848 1-136-601-11 FILM 0.001UF...
Page 56
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK R1105 1-216-825-11 METAL CHIP 2.2K 5% 1/10W < IC > R1106 1-216-809-11 METAL CHIP 1/10W IC701 8-759-562-43 IC TDA6108JF/N1B < SWITCH > IC1801 8-759-603-37 IC M5216P S6100 £...
Page 57
All manuals and user guides at all-guides.com REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK C Board Variant Parts 28HX15 MISCELLANEOUS < RESISTOR > £ 1-786-649-11 SWITCH, AC POWER PUSH £ 1-783-083-11 CORD, POWER (WITH FILTER) R704 1-216-361-00 METAL OXIDE 0.22 5% 2W £...
Page 58
• User programmable Functional Check through Infrared • Fast and documented Test Mode setting of all Sony TV chassis Additional features such as Adjustments and Troubleshooting are available in chassis-dependent software modules. Please contact your local Sony Service organisation for the latest information.
Need help?
Do you have a question about the TRINITRON KV-28HX15B and is the answer not in the manual?
Questions and answers