Toro Groundsmaster 4500-D Installation Instructions Manual
Hide thumbs
Also See for Groundsmaster 4500-D:
- Service manual (474 pages) ,
- Operator's manual (92 pages) ,
- Installation instructions manual (28 pages)
Advertisement
Quick Links
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description
No parts required
No parts required
Flow divider
Pressure hose
Manifold tube
Traction-motor tube
Divider tube
Bolt
Flange nut
Important:
This kit is only intended for use with Groundsmaster Models 30881, 30882, 30873, 30873TE,
30874, and 30874TE serial numbers 316999999 and below.
Note:
The procedures for installing this kit require that you work from under the machine.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
CV
Flow Divider Kit
Groundsmaster
®
Model No. 30876
Register at www.Toro.com.
4500-D/4700-D Traction Unit
Qty.
–
Prepare the machine.
–
Remove the hydraulic lines.
1
1
1
1
Install the hydraulic components.
1
2
2
Form No. 3386-618 Rev B
Installation Instructions
Use
Original Instructions (EN)
All Rights Reserved *3386-618* B
Printed in the USA
Advertisement
Related Manuals for Toro Groundsmaster 4500-D
Summary of Contents for Toro Groundsmaster 4500-D
- Page 1 This kit is only intended for use with Groundsmaster Models 30881, 30882, 30873, 30873TE, 30874, and 30874TE serial numbers 316999999 and below. Note: The procedures for installing this kit require that you work from under the machine. © 2020—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3386-618* B...
-
Page 2: Preparing The Machine
Preparing the Machine Removing the Hydraulic Lines CAUTION If you leave the key in the ignition switch, Removing the Pressure Hose someone could accidently start the engine Align a drain pan below the forward end of the and seriously injure you or other bystanders. pressure hose (Figure 1 Figure... - Page 3 Removing the Cross Tube Align the drain pan below the rear-traction manifold. Remove the tube nut for the cross tube from the fitting in the rear-traction manifold (Figure Remove the tube nut for the filter tube from the fitting in the cross tube, and remove the cross tube (Figure Note:...
- Page 4 Installing the Hydraulic Installing the Rear-traction Tube and the Pressure Hose Components Align the forward tube nut for the rear-traction tube with the elbow fitting in the flow divider Installing the Flow-divider (Figure 4 Figure Manifold Align the holes in the flow-divider manifold with the holes in the chassis bracket.
- Page 5 Installing the Cross Tube Remove the cap on the fitting of the rear-traction manifold that you previously installed. Align the tube nuts for the cross-manifold tube to the fittings in the rear-traction manifold and the flow divider (Figure g027293 Figure 5 1.
- Page 6 Installing the Filter Tube and the Installing the Traction-motor Tube Divider Tube Align the tube nuts for the traction-motor tube to the fittings in the traction motor and the flow Align the tube nut for the hydraulic-filter tube to divider (Figure the fitting in the cross-manifold tube as shown Figure...
-
Page 7: Operation
Checking for Hydraulic Leaks Operation WARNING Operating Tips Hydraulic fluid escaping under pressure can penetrate skin and cause injury. The flow divider kit enhances the traction drive performance in compromised operating conditions. • Make sure that all hydraulic fluid hoses and lines are in good condition and all The flow divider kit splits the traction flow evenly hydraulic connections and fittings are tight... - Page 8 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Need help?
Do you have a question about the Groundsmaster 4500-D and is the answer not in the manual?
Questions and answers