Contents 1 Important Safety 2 Your multiroom speaker Introduction What's in the box Overview of the main unit 3 Prepare Connect power and turn on 4 Play Play in single mode Play in group mode Control play 5 Other features Listen to an external device Update firmware Reset group status...
1 Important Safety • Make sure that there is enough free space around the product for ventilation. • Only use attachments or accessories specified by the manufacturer. • Use only power supplies listed in the user manual. • The product shall not be exposed to dripping or splashing.
2 Your multiroom speaker Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. Introduction With the Philips izzylink speaker, you can: • listen to music from your Bluetooth- enabled devices;...
Overview of the main unit abc d e f g h ij k e Volume indicator • Lights up after power-on. • Turn the speaker on or off. • Dims in standby mode. b GROUP button/indicator • Flashes when the speaker is muted. •...
Page 7
• Start, pause, or resume play. h AUDIO IN • Audio input socket (3.5mm) for an external audio device. i SOFTWARE UPGRADE • USB socket for speaker software upgrade only. j GROUP RESET • Press with a sharp object to restore factory defaults.
Always follow the instructions in » The volume indicator lights up. this chapter in sequence. » The signal strength indicators flash If you contact Philips, you will be asked for several seconds until the speaker for the model and serial number of boots up.
Page 9
Switch to standby mode • In single mode, press . » The volume indicator dims. » All the other indicators turn off. • In group mode, press on any speaker in the group. » The volume indicator on each speaker in the group dims.
Bluetooth device is approximately 10 meters (30 feet). Bluetooth and search for Bluetooth devices (refer to the user manual of the device). When [Philips BM5 XXX] is displayed on your device, select it to start pairing and connection. If necessary, enter the default password “0000”.
Play from the connected Bluetooth- indicator Description Flashing blue Connecting or waiting enabled device for connection Solid blue Connected Note • Music play pauses when there is an incoming call or video recording is in progress on the connected mobile phone.
Page 12
Create a group Connect a Bluetooth-enabled device to the master and play to the whole group Note • Music play pauses when there is an incoming call or video recording is in progress on the connected mobile phone. If no Bluetooth connection has been set up with the master speaker before, pair and connect a Bluetooth-enabled device to the Note...
master speaker sets up connection Control play with its slaves. » The volume indicator on the speaker Note turns white while that on the previous • master speaker turns green. Due to data buffering, you may experience some delay when you play/pause or adjust volume from the Bluetooth device.
Note • Make sure that the USB stick is FAT16/32 formatted. On your PC/Mac, go to www.philips.com/ support. Enter the model number to find the latest firmware upgrade file available. Connect an audio cable with a 3.5 mm...
Do not remove the USB stick, and wait for around 3 to 4 minutes for completion of the firmware upgrade. www.philips.com/support » At completion of firmware upgrade, all indicators on the speaker flash at the same time. XXXX Reset group status XXXX.
10 m (free space) Speakers Speaker Impedance 4 ohm Speaker Driver 4 cm full range Sensitivity > 81dB/m/W +/- 3dB/m/W General information AC power Input: 100 - 240 V~ 50/60 Hz 0.3 A PHILIPS Output: 5 V Switching power supply model: Y10DE-050-2000 (KINGS)
If the problem remains unsolved, go to the Philips Web page (www. Bluetooth cannot be connected with this philips.com/support). When you contact Philips, speaker.
8 Understand Two indicators The signal strength of lighting up group connection is good. meanings of Only one indicator The signal strength lighting up of group connection LED status is poor. Move slave speakers closer to the master speaker. No indicator The speaker is powered lighting up off or working in single...
Page 19
Meaning Bluetooth indicator status The speaker is powered off. The speaker acts as a slave in group mode. The speaker is grouping with its master/slave. Flashing The speaker is in pairing mode. blue Solid blue The speaker is connected to a Bluetooth-enabled device.
Open Source Team, Gibson electronic products. Follow local rules and Innovations Limited, 5/F Philips Electronics never dispose of the product with normal Building, 5 Science Park East Avenue, Hong household waste. Correct disposal of old Kong Science Park, Shatin, N.T.
Page 22
This product has been manufactured by, and is sold under the responsibility of Gibson Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
Need help?
Do you have a question about the BM5W/10 and is the answer not in the manual?
Questions and answers