Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Power Supply - Diagram and Board Layout Electrical Diagram and Board Layout of Power Supply Boards (PSU) applied in 8601 sets can be downloaded from Philips for Servicers website. Look for service information of QM15.1E LA and open Symptom & Cure GSC_109938.
Page 3
Technical Specs, Diversity, and Connections QM15.1E LA EN 3 Connections Side Connectors Rear Connectors AUDIO IN SERV.U /CVBS Bottom Rear Connectors TV ANTENNA DIGITAL AUDIO OUT S A T E L L I T E NETWORK HDMI HDMI WIRELESS OPTICAL AUDIO 19800_001_150911.eps 15-09-11...
Page 4
Technical Specs, Diversity, and Connections EN 4 QM15.1E LA 2.3.1 Side Connections 6 - HDMI: Digital Video - In, Digital Audio - In/Out 1 and 2 - Common Interface 1 and Common interface 2 68p - See Figure 10-1-18 10000_017_090121.eps 090428 3 - USB3.0 Figure 2-5 HDMI (type A) connector...
Technical Specs, Diversity, and Connections QM15.1E LA EN 5 2.3.2 Rear Connections - TD+ Transmit signal - TD- Transmit signal - RD+ Receive signal 8- Wireless Audio - In - CT Centre Tap: DC level fixation Bk - - CT Centre Tap: DC level fixation - RD- Receive signal...
Spare Parts the following points: • Route the wire trees correctly and fix them with the For the latest spare part overview, consult your Philips Spare mounted cable clamps. Part web portal. • Check the insulation of the Mains/AC Power lead for external damage.
Precautions, Notes, and Abbreviation List QM15.1E LA EN 7 result in sets which have the same CTN (Commercial Type 6 = play 16 : 9 format, 12 = play 4 : 3 Number; e.g. 28PW9515/12) but which have a different B.O.M. format number.
Page 8
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 9
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4-wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
4.3 Set Disassembly / Assembly 4.4 Set Re-assembly Cable Dressing Refer to 9. SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams for detailed Wiring Diagrams. 19800_009_150912.eps 15-09-12 Figure 4-1 Cable dressing 55" 8601 series back to 2016-May-09 div.table...
Page 11
Mechanical Instructions QM15.1E LA EN 11 19800_011_150912.eps 23-09-12 Figure 4-2 Cable dressing 55" 8601 series (inside Backcover) back to 2016-May-09 div.table...
Mechanical Instructions EN 12 QM15.1E LA 19800_011_150912.eps 15-09-12 Figure 4-3 Cable dressing 65" 8601 series 19800_011_150912.eps 15-09-23 Figure 4-4 Cable dressing 65" 8601 series (inside Backcover) back to 2016-May-09 div.table...
TV set. 4.3.1 Removing the Backcover 8601 series Instructions below apply to the 55PUS8601/12, but are similar for other 55” and 65" 8601 series models. Caution! 19800_018_150929.eps Carefully follow the instructions to avoid damaging the...
Page 15
6. Use dissolvent to fully remove the remaining double sided too much pressure on the backcover. tape from the Backcover and from the Display panel. Screws M3×6: 23x to panel + 3x to I/O brackets 19800_015_150914.eps 15-10-28 Figure 4-11 Backcover Screw Location 8601 series 55” back to 2016-May-09 div.table...
Page 16
EN 16 QM15.1E LA Screws M3×6: 25x to panel + 3x to I/O brackets 19800_029_151030.eps 15-10-30 Figure 4-12 Backcover Screw Location 8601 series 65” 4.3.2 Mounting the Backcover 8601 series Attention! When mounting the backcover after repair, don’t forget to put new pieces of double sided tape on the display panel before closing the backcover.
Page 17
Backcover. 55PUS8601 19993_001_160509.eps 16-05-09 Figure 4-13 Double Sided Tape on Deco frame of 8601 series 55” Procedure 1. Paste four pieces of double sided tape of 70 cm on the Deco frame: two at the Top, one Left side, one Right side.
Page 18
Insert and tighten all other screws. 19800_030_151030.eps 15-10-30 4.3.5 Keyboard Control unit 8601 series Figure 4-16 Keyboard removal 1. Unplug the AmbiLight FFC connectors [1] and 13 pins connector [2] from the keyboard control panel. 2. Remove the fixation screws that secure the keyboard.
Page 19
AL 7 LED AL 8 LED AL 7 LED AL 10 LED AL 10 LED AL 3 LED AL 3 LED AL 7 LED AL 8 LED 19800_044_151204.eps 15-12-04 Figure 4-17 AmbiLight and Keyboard removal 8601 series back to 2016-May-09 div.table...
Page 20
Mechanical Instructions EN 20 QM15.1E LA 4.3.7 Removing the AmbiLight Projection Module 8901 series 4.3.8 Mounting the AmbiLight Projection Module 8901 series Refer to Figure 4-18 for details. Refer to Figure 4-18 for details. 1. Disconnect Power Cable 8P9 from the AmbiLight driver 1.
Mechanical Instructions QM15.1E LA EN 21 4.3.9 Small Signal Board (SSB) 4.3.10 Power Supply Unit (PSU) Instructions for removing the SSB Caution: Refer to Figure 4-19 for details. During re-assembly insert all different screws at the original 1. Release the clips (1) from the LVDS connector that position.
Page 22
Set Re-assembly To re-assemble the whole set, execute all processes in reverse order. 19800_022_151011.eps 15-10-11 Figure 4-22 Number of Magnets on Deco Bezel 8601 series Refer to Figure 4-23 for the mounted two piece and three piece magnet assemblies. back to 2016-May-09 div.table...
Service Modes, Error Codes, and Fault Finding QM15.1E LA EN 23 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: Display Option Code Selection 5.1 Service Modes After an SSB or display exchange, the display option code is 5.2 Stepwise Start-up not properly set, it will result in a TV with “no display”.
Service Modes, Error Codes, and Fault Finding EN 24 QM15.1E LA 5.1.2 Service Alignment Mode (SAM) • Option settings. • Allow Software alignments (White Tone Values). • NVM Editor. Purpose • Set screen mode to full screen (display all content). In Service Alignment Mode service personnel can: •...
Service Modes, Error Codes, and Fault Finding QM15.1E LA EN 25 5.1.3 Factory mode • Etc. Purpose How to Activate the Factory mode In Factory Mode you can perform extended alignments: From the “menu/home”, using the remote control, key in “1999” •...
Page 26
Service Modes, Error Codes, and Fault Finding EN 26 QM15.1E LA How to Exit Factory mode From the menu, using remote control, select “EXIT_FACTORY” and press button “OK”. Note When the TV set, being in factory mode, is switched “off” by power interruption or from normal operation to “stand-by”, then the TV set will show up in “normal operation mode”...
Page 27
Displays the built-in main software version. In case of field problems related to software, software can be upgraded. As this software is consumer upgradeable, it will also be available on the Internet: http://www.p4c.philips.com. • 2.2 Standby Software Displays the built-in stand-by processor software version.
Page 28
Service Modes, Error Codes, and Fault Finding EN 28 QM15.1E LA • 3.9 Event counter How to Exit CSM The counter of events. To exit CSM, press one of the following buttons: • “MENU/HOME” on remote control. • “POWER” on remote control or on TV set. How to Navigate CSM To navigate through the menus use the “CURSOR-DOWN/UP”...
Page 29
How to upgrade the main software is described in the user manual or on the Philips website (P4C). 5.4.2 Introduction Philips continuously tries to improve its products. So, it’s advisable to update TV software as soon as an update is 19080_207_110324.eps available.
Service Modes, Error Codes, and Fault Finding EN 30 QM15.1E LA 5.4.6 How to copy NVM data to/from USB stick • In SAM mode. – When SAM is entered via Remote Control, then LAYER 2 is displayed via blinking LED. Use folder “repair”...
Page 31
Service Modes, Error Codes, and Fault Finding QM15.1E LA EN 31 Table 5-4 Error Code Overview Error / Blinking LED / Description Layer 1 Layer 2 Monitored by Medium Prot Error Buffer I²C address Defective Board I²C Busses FE-bus FE bus or via SSB bus BL / EB Cypress bus Cypress bus...
Page 32
Service Modes, Error Codes, and Fault Finding EN 32 QM15.1E LA • Activate SAM. The blinking front LED will show the entire • We can not yet conclude that flash RAM and DRAMs are content of the LAYER 2 error buffer, this works in “normal fully operational/reliable.There still can be errors in the data operation”...
Alignments QM15.1E LA EN 33 6. Alignments Index of this chapter: • Select “RGB Align.” and choose a color temperature. 6.1 General Alignment Conditions • Use a 100% white screen as input signal and set the 6.2 Hardware Alignments following values: 6.3 Software Alignments –...
For core SSB spare part diversity Table, refer to Symptom & 3. Restart the set immediately after resetting the Display Cure GSC_111364 from Philips Servicer Network Support. Code. Remark • Core SSB spare part (based on high runner) with same HW diversity in a group is provided.
Page 35
Alignments QM15.1E LA EN 35 • Core SSB spare part can be used in other CTNs within same HW group by changing Panel Code, option code wherever applicable. • Latest SW is to be loaded to Core SSB from P4C if required.
Circuit Descriptions EN 36 QM15.1E LA 7. Circuit Descriptions Introduction Index of this chapter: 7.1 Introduction The QM15.1E LA is a new chassis launched in Europe in 7.2 Power Supply 2015. The whole range is covered by MT5593U+. 7.3 Ambilight The QM15.1E LA chassis comes with the following stylings: Notes: •...
Circuit Descriptions QM15.1E LA EN 37 7.1.2 SSB Cell Layout COMMON INTERFACE POWER BACK-END SOC1 MT 5593 USB 3 Audio Class-D USB 2 HDMI 4 FRONT-END HDMI 3 Channel Decoders ANALOG SCART Headphone Dual Tuner USB 1 HDMI 2 HDMI 1 Wireless Audio SPDIF Satellite 1 &...
Page 38
Circuit Descriptions EN 38 QM15.1E LA 7.1.3 Bolt on Layout NT324 19800_003_150912.eps 15-09-12 Figure 7-2 Bolt-on layout cells (top view) back to 2016-May-09 div.table...
Page 39
3V3-DVBT F004F specifications! This part is available in the regular market. V-LNB F012F Consult the Philips Service web portal for the order codes of the 3V3-LAN F027U boards. 1V0-M I057B 1V5-M...
Page 40
Circuit Descriptions EN 40 QM15.1E LA 7.2.3 Power Layout SSB +3V3-WiFi AMBIPOWER LNBOUT-B +1V0VCCK +1V1-NT +1V8-EMMC-IO +2V5-NT +1V2 LNBOUT-A +5-SW +1V5-DDR +3V3 +1V0-BST 19800_038_151121.eps 15-11-21 Figure 7-4 Power SSB Top View back to 2016-May-09 div.table...
Page 41
Circuit Descriptions QM15.1E LA EN 41 +1V0-AVDD +3V3-NT +1V2 +3V3-Standby +3V3-DVB +1V5-NT +3V5-SB 19800_039_151121.eps 15-11-21 Figure 7-5 Power SSB Bottom View back to 2016-May-09 div.table...
Page 42
AmbiLight color and brightness change to create a sense of 15-10-26 being personally on the screen. Refer to Figure 7-7 for AmbiLight boards used in 8601 series. Figure 7-7 AmbiLight Board Diversity 8601 Series • AmbiLight 4 configuration. • AmbiLight boards power supply voltage is 12V.
IC Data Sheets QM15.1E LA EN 43 8. IC Data Sheets This chapter shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
Page 44
IC Data Sheets EN 44 QM15.1E LA Personal Notes: 10000_012_090121.eps 110804 back to 2016-May-09 div.table...
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 45 9. SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams Architectural Diagram MTK 5593U+ with PQ BO MTK EU/RU 2T UHD50/100 + PQ BO 2x DDR3 2x DDR3 1x DDR3 EU#2...
Page 46
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 46 Connection Diagram MTK 5593U+ with PQ BO Removed M0-RESETn M1-RESETn M2-RESETn eMMC-RESETn Control Architecture Serial Flash EEPROM 2015 MT5593 EU3 4Mbit = 512kB 0xA0 Audio Board CN1043 I²C-HDMI HDMI-MUX-RESETn...
Page 47
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 47 MTK 5593U+ Floor Plan and Connector Locations MT5593 EU#3 - Floorplan MT5593 EU#3 - Connector Locations AL + Key 2D DIMMING USB CAMERA CN1111 POWER USB CAMERA CN1112 POWER AL + Key...
Page 48
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 48 Power Architecture MTK 2k15 - PSU Connector and Back End Power Architecture MTK 2k15 Connector from PSU CN1190 +3V5-STANDBY +3V3 +3V5-STANDBY D4300 D4303 +12V +3V3-STANDBY Back End +12V-AMBI +12V-AMBI +3V5-SB...
Page 49
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 49 Power Architecture MTK 2k15 - Front End Power Architecture MTK 2k15 - Front End +12V +3V5-SB U4403 U4401 /U4400 U4307 U4101 U4301 DC/DC DC/DC DC/DC DC/DC Start up: +3V3 DC/DC LNBH26LSP...
Page 50
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 50 Wiring Diagram 55" 8601 series Wiring Diagram 55” 8601 series 55PUS8601 (MTK) 1004 - TFT screen 8PS 1316 8PS1319 1040 - Bolt on 1050 - PSU...
Page 51
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 51 Wiring Diagram 55" 8601 series Backcover Wiring Diagram 55” 8601 series Backcover (View inside) 8AL05 8AL04 8AL03 8AL02 55PUS8600 Backcover 8AL06 8AL01 8AL07 8AL08 8AL09 8AL10 19800_005_150912.eps...
Page 52
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 52 Wiring Diagram 65" 8601 series Wiring Diagram 65” 8601 series Conductors Conductors facing down ! facing down ! 65PUS8600 8PS1339 8PS1336 8PS1326 8PS1329 Mandatory Mandatory posi on...
Page 53
EN 53 Wiring Diagram 65" 8601 series Backcover Wiring Diagram 65” 7600 series - Backcover Wiring Diagram 65” 8601 series Backcover (View inside) 1225 - Ambilight Module 9 LED 1224 - Ambilight Module 8 LED 1223 - Ambilight Module 9 LED...
Page 54
SSB Block Diagrams, SSB Floor Plans and Set Wiring Diagrams QM15.1E LA EN 54 9.10 Wiring Diagram 65" 8901 series Wiring Diagram 65” 8901 series - PICO PROJECTOR AMBILIGHT TV 8PS1336 8PS1339 8PS1326 8PS1329 8CN1160 8CN1161 8CN0006 8CN0016 9x 8CN1060 !!! PRIMARY HOT ZONE !!! 19992_003_151209.eps 15-12-09...
QM15.1E LA EN 84 10-1-30 SSB 715G7132 - Thermal Foam Location on 8601 series MTK 2k15 - 715G7132M0B000005K - Location of Thermal Foams (to be placed on display panel) Silkscreen lines are applied directly under the IC thermal foam positioning...
Circuit Diagrams and PWB Layouts QM15.1E LA EN 85 10-1-31 SSB 715G7132 - Thermal Foam Location on 8901 series Position 450 (30 x 30 x 11, Blue) Position 451 (40 x 40 x 11, Blue) 35 ±1 37 ±1 97.5 ±1 137 ±1 Procedure Placing Thermal Foams 1.
Circuit Diagrams and PWB Layouts QM15.1E LA EN 103 10-2-18 Bolton Cu23b - 715G7085 - Thermal Foam Location MTK 2k15 - BLTON-Cu23b - 715RLPCS000000044x - Location of Thermal Foams (to be placed on display panel) Silkscreen lines are applied directly under the IC thermal foam positioning Position 0451 Position 0454...
Circuit Diagrams and PWB Layouts QM15.1E LA EN 104 10.3 J 715G7074 IR/LED Panel 10-3-1 IR & 3D & Light sensor & LOGO IR & 3D & Light sensor & LOGO Standby Lighting LOGO IR Receiver 3V3SB 3V3SB CN201 3V3SB 3V3SB LED_R 3V3SB...
Circuit Diagrams and PWB Layouts QM15.1E LA EN 108 10.5 E 715G7065 Keyboard control panel 10-5-1 Key+AL KEY + AL CONN TO SSB JOYSTICK Direction switch Key functionResistance Voltage Center 2-5 short Menu CN01 CN01 CN04 CN04 Right 1-5 short 0.5V KEY1 AMBI_SPI_CLK...
Page 109
Circuit Diagrams and PWB Layouts QM15.1E LA EN 109 10-5-2 Key board layout Layout Keyboard control panel (top side) CN04 CN01 Layout Keyboard control panel (bottom side) SW01 2014-11-06 Keyboard control panel 715G7065 layout top/bottom 19812_518.eps back to 2016-May-09 div.table...
Need help?
Do you have a question about the 8601 Series and is the answer not in the manual?
Questions and answers