Advertisement
Quick Links
H
i
t
a
c
h
H
i
t
a
c
Q
u
i
c
k
I
n
s
t
a
l
l
a
t
i
o
n
G
Q
u
i
c
k
I
n
s
t
a
l
l
a
t
i
o
n
G
H
i
t
a
c
h
i
U
l
t
r
a
s
t
a
r
1
0
K
H
i
t
a
c
h
i
U
l
t
r
a
s
t
a
r
1
0
K
M
o
d
e
l
s
:
H
U
S
1
0
3
M
o
d
e
l
s
:
H
U
S
1
0
3
H
H
U
U
S
S
1
1
0
0
3
3
H
U
S
1
0
3
H
U
S
1
0
3
_________________________________
Handling precautions
•
Do not open the electrostatic discharge
(ESD) bag containing the drive until
required.
•
Do not apply pressure on the drive during
handling and installation.
•
To prevent damage from impact or vibration
always set the drive down gently.
•
Handle the drive carefully by the edges. Do
not touch the exposed printed circuit board
or any electronic components.
•
Do not cover the breather hole! Covering the
breather hole may result in loss of data.
•
Save the packaging materials including the
ESD bag in the event that the drive must be
returned.
Installing the drive
1. Record the serial number and part number
of your hard drive for future reference
.
2. Turn off the computer and remove the
computer system cover
.
3. Before handling the hard disk drive,
discharge any static electricity from yourself
and your clothing. With one hand touch an
unpainted metal surface on the computer
chassis, and then touch the ESD bag with
the other hand for a minimum of two
seconds.
4. Remove the hard drive from the ESD bag.
5. Unplug the computer.
6. Assign a SCSI address if necessary.
Page 1
i
G
l
o
b
a
l
S
h
i
G
l
o
b
a
l
S
u
i
d
e
u
i
d
e
3
0
0
3
0
0
0
3
0
F
L
3
6
0
0
H
U
S
1
0
3
0
3
0
3
0
F
L
3
6
0
0
H
U
S
1
0
3
0
0
0
1
1
4
4
F
F
L
L
3
3
6
6
0
0
0
0
H
H
U
U
S
S
1
1
0
0
3
3
0
0
1
0
7
3
F
L
3
6
0
0
H
U
S
1
0
3
0
7
0
7
3
F
L
3
6
0
0
H
U
S
1
0
3
0
t
o
r
a
g
e
T
e
c
h
t
o
r
a
g
e
T
e
c
h
0
F
L
3
8
0
0
3
0
F
L
3
8
0
0
1
4
4
F
F
L
L
3
3
8
8
0
0
0
0
3
F
L
3
8
0
0
7
3
F
L
3
8
0
0
______________________________________
Wide LVD 68pin-16bits (NW)
Option Jumper Connector (C3)
Note: The SCSI ID setting is to be set via the eC3
connector (not by the C4.) In case the SCSI ID
setting is done by remote switch via the C4
connector and remote cable, remove all Jumper
Sockets from the C3 connector to avoid ID
control conflicts.
n
o
l
o
g
i
e
s
n
o
l
o
g
i
e
s
Pin
Signal Name
Pin
No
No.
1
ID3
2
3
ID2
4
5
ID1
6
7
ID0
8
Disable Auto
9
10
Start
Force Single
11
12
Ended mode
Enable
13
14
Delayed Start
15
Write Protect
16
17
Reserved
18
19
Reserved
20
LED(with 0
21
22
ohm)
Term. Power
22
24
to SCSI bus
version 1.0
Signal Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
5Vwith 150
ohm
Term Power
to SCSI bus
Advertisement
Related Manuals for Hitachi Ultrastar 10K300
Summary of Contents for Hitachi Ultrastar 10K300
- Page 1 _________________________________ Handling precautions • Do not open the electrostatic discharge (ESD) bag containing the drive until required. • Do not apply pressure on the drive during handling and installation. • To prevent damage from impact or vibration always set the drive down gently. •...
- Page 2 References in this publication to Hitachi Global Storage Technologies products, programs or services do not imply that Hitachi Global Storage Technologies intends to make these available in all countries in which Hitachi Global Storage Technologies operates.
Need help?
Do you have a question about the Ultrastar 10K300 and is the answer not in the manual?
Questions and answers