hit counter script
Panasonic AG-1340P Service Manual
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. VCR
  5. ProLine AG-1340P
  6. Service manual

Panasonic AG-1340P Service Manual

Hide thumbs Also See for AG-1340P:
Table of Contents

Advertisement

Quick Links

Download this manual
ORDER NO. BSD0109M021
D01
Video Cassette Recorder
AG-1340P
Z-MECHANISM
2001 Matsushita Electric Industrial Co., Ltd. All rights reserved.
Unauthorized copying and distribution is a violation of law.
Please refer to the service manual for Z-Mechanism Chassis
and the Operating Instructions in the appendix folder. /
(Go
to Appendix List)
1
PDF created with pdfFactory Pro trial version
www.pdffactory.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AG-1340P and is the answer not in the manual?

Questions and answers

Related Manuals for Panasonic AG-1340P

Summary of Contents for Panasonic AG-1340P

  • Page 1 ORDER NO. BSD0109M021 Video Cassette Recorder AG-1340P Z-MECHANISM 2001 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. Please refer to the service manual for Z-Mechanism Chassis and the Operating Instructions in the appendix folder. /...
  • Page 2 SAFETY PRECAUTIONS GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short / circuit is found, replace all parts which have been over-heated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
  • Page 3 prevent the customer from being exposed to shock hazards. LEAKAGE CURRENT COLD CHECK 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohm meter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc.
  • Page 4 there is a possibility of a shock hazard, and the equipment should be repaired and checked before it is returned to the customer. ELECTROSTATICALLY SENSITIVE (ES) DEVICES Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically sensitive (ED) Devices.
  • Page 5 installed. / CAUTION : Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpacked replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device).
  • Page 6 6. Schematic Diagrams NOTE BE SURE TO MAKE YOUR ORDERS OF REPLACEMENT PARTS ACCORDING TO PARTS LIST. CAUTION MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. / PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR SERVICE OF THE PRODUCTS.
  • Page 7 CAUTION MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. / PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR SERVICE OF THE PRODUCTS. IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
  • Page 8 NOTE: 1. Be sure to make your orders of replacement parts according to this list. 2. Unless otherwise specified, all resistors are in OHMS, K=1,000 OHMS, all capacitors are in MICROFARADS ( F), P= 3. The P.C. Board untils marked with " "...
  • Page 9 AG-1340P 1 GENERAL DESCRIPTIONS [2. HOW TO CONFIRM THE “NAVI.” DATA WITHOUT 1.1. SERVICE CAUTION-1 INSERTING A TAPE INTO VCR?] When the Microprocessor IC6001 and/or Back-up battery 1. Indicate the “NAVI” mark on the Front information Panel. B6001 are replaced, read following procedure carefully and (Press the Menu button and select the option, then set the proceed it.
  • Page 10 AG-1340P STEP 2. “NAVI” DATA BACK-UP PROCEDURE F.I.P. DISPLAY Turn on the Service Mode. 1. Press FF and EJECT keys simultaneously for more than 3 seconds. Turn on the Service Mode 2. 2. Press FF and EJECT keys in twice.
  • Page 11 (See Fig.B1) Fig.B1 NOTE: The lithium battery is a critical component (Type No.:CR2354-1GUF Manufactured by Panasonic.) It must nerver be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
  • Page 12 AG-1340P 1.3. SERVICE CAUTION-2 1.3.1. CAUTION FOR AUTO TUNING PROCEDURE Auto Tuning will start by the following procedure. 1. Connect the DIN-RF Cable. 2. Connect the AC Mains Lead. 3. Turn on the VCR. Auto Tuning will start. Auto Tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned program position.
  • Page 13 AG-1340P Fig. S5 d. Rotate Main Cam Gear to the clockwise in order to eject the cassette tape. 1.3.4. CYLINDER UNIT REPLACEMENT 1. CYLINDER UNIT REPLACEMENT a. Remove the Mechanism unit from MAIN C.B.A./Chassis by referring “Disassembly Procedure”. b. Remove the 3 screws (A) of the CYLINDER UNIT with a screw driver.
  • Page 14 AG-1340P necessary. 1.3.5. FLAT CARD CABLE INSTALLATION When installing the Flat Card Cable on the connector, install the Flat Card Cable with the cable contacts facing the connector contacts. Fig. S8 c. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on Fig.
  • Page 15 AG-1340P 4 INPUT/OUTPUT CHART 4.1. INPUT/OUTPUT CHART FOR IC6001...
  • Page 16 AG-1340P...
  • Page 17 8 EXPLODED VIEWS & REPLACEMENT PARTS LIST SERVICING FIXTURES & TOOLS Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VFM8080HQFP VHS ALIGNMENT TAPE VFK0335 RETAINING RING REMOVER VFK0329 POST ADJ. SCREWDRIVER VFK0326 HEX WRENCH SET VFK0132A BACK TENSION METER...
  • Page 18 CHASSIS PARTS SECTION PRT-2...
  • Page 19 CHASSIS PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VHN0311 PUSH NUT VEG1537 CYLINDER UNIT VXP2026 UPPER CYLINDER UNIT 1 SUPPLIED FROM MAV VMX2208 CUT WASHER VDB1256 CYLINDER RETAINER W2,W3 VMX3022 WASHER VEK8840...
  • Page 20 CASING PARTS SECTION PRT-4...
  • Page 21 CASING PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VGM1802 TOP PANEL 1 SUPPLIED FROM MAV VYP8238 FRONT PANEL ASS'Y VKA0192 VKF3397 BLINDER PANEL 1 SUPPLIED FROM MAV VMB2521 BLINDER SPRING VKA0192 VJH1185 ANT BOARD...
  • Page 22 PACKING PARTS SECTION PRT-6...
  • Page 23 PACKING PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VQT9136 OPERATING INSTRUCTIONS N2QAHB000010 REMOTE CONTROLLER K2KZ2BA00001 RF CABLE VJA0488 POWER CODE 1 K2CG3CH00001 VPN5359 CUSHION (L) VPN5360 CUSHION (R) VPG0J11 PACKING CASE 1 SUPPLIED FROM MAV PRT-7...
  • Page 24 :TO SYSTEM CONTROL & SERVO / TIMER SECTION CAUTION MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. D1180 MAZ751000C D1181 T1150 G4D2A0000051 ZA1105...
  • Page 25 :VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :CAPSTAN SERVO PHASE LOOP :CYLINDER SERVO SPEED LOOP :VIDEO MAIN SIGNAL PATH IN REC MODE :CAPSTAN SERVO SPEED LOOP :CYLINDER SERVO PHASE LOOP <A-LINE> <A-LINE> (A14) (A15) (A17) (A11) (A19) (A28) (A29) (A31) (A32) (A15) (A14)
  • Page 26 :GRID CONTROL SIGNAL PATH SYSTEM CONTROL & SERVO ICs VOLTAGE CHART (SP MODE) :SEGMENT CONTROL SIGNAL PATH Ref.No. IC2501 MODE MODE SW <A-LINE> STOP 14.4 14.4 14.7 1.1 14.4 S2001 VSS0520-4 DP7501 PLAY 14.3 14.3 14.6 1.1 14.3 (A33) A2BD00000040 14.3 14.3 14.6 0.8 14.3 (A18)
  • Page 27 : VIDEO MAIN SIGNAL PATH IN REC MODE : AUDIO MAIN SIGNAL PATH IN REC MODE : VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE : AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE <A-LINE> <A-LINE> <A-LINE> :TO AUDIO SECTION (A8) (A9) (A7) (A10) (A6)
  • Page 28 <C-LINE> <12.0V> (C1) D A REC(H) Q4003 R4039 BIAS(L) 2SD1149 <5.0V> A/V 5.0V (4.7) (REC CONT.) (C1) <12.0V> 12.0V (C2) OSD CV IN (-27.0) 0.6(-27.3) (C2) <5.0V> R4037 (C4) PICT 2 4700 QR4001 UN2111 (C6) FSC IN (-18.1) R4038 (REC CONT.) 2200 (C8) <5.0V>...
  • Page 29 : AUDIO MAIN SIGNAL PATH IN REC MODE : AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE : TO VIDEO SECTION : VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE : TO SYSTEM CONTROL &SERVO SECTION : VIDEO MAIN SIGNAL PATH IN REC MODE LINE OUT LINE IN VIDEO...
  • Page 30 AG-1340P 3 ABBREVIATIONS...
  • Page 31 AG-1340P...
  • Page 32 AG-1340P...
  • Page 33 AG-1340P...
  • Page 34 SYSTEM CONTROL & SERVO / TIMER SECTION BLOCK DIAGRAM :MAIN SIGNAL PATH IN REC MODE :MAIN SIGNAL PATH IN PLAYBACK MODE :CAPSTAIN SERVO SPEED LOOP :CAPSTAIN SERVO PHASE LOOP :CYLINDER SERVO SPEED LOOP :CYLINDER SERVO PHASE LOOP IC7501 TIMER IC6001 SYSTEM CONTROL & SERVO DP7501 TIMER DISPLAY POS.
  • Page 35 VIDEO/AUDIO SECTION BLOCK DIAGRAM :AUDIO MAIN SIGNAL PATH IN REC MODE :AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :VIDEO MAIN SIGNAL PATH IN REC MODE :VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE X3001 TW3001 QR3011 PICT 2 TO/FROM SYSCON & SERVO Q3009 SECTION OSD VIDEO IN...
  • Page 36 MAIN P.C.BOARD (VEP06E21J) MAIN P.C.BOARD Transistor Test Land Q1150 TL2015 Q1151 TL4507 Q1152 TL4552 Q1153 TL6001 Q1200 TL6010 Q1341 TL6012 Q2001 TL6013 Q2002 TL7509 Q3004 TL7510 Q3005 Q3009 PGND Q3010 Q4003 Test Wire Q4004 TW1004 Q4005 TW2001 Q4006 TW2002 Q4007 TW3001 Q4501 TW6001...
  • Page 37 ORDER NO. BSD0109M021 Video Cassette Recorder AG-1340P Z-MECHANISM Adjustment procedures, Disassembly Procedures and Assembly Procedures for Mechanism Chassis are separate volume from this service manual. (refer to the appendix in this CD-ROM.) Please refer to the service manual for Z-Mechanism Chassis. (Order No. VSD9706M201, VRD9802005C2) ©...

  • Page 38: Table Of Contents

    WARNING This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians.

  • Page 39: Safety Precautions

    SAFETY PRECAUTIONS GENERAL GUIDELINES ELECTROSTATICALLY SENSITIVE (ES) DEVICES 1. When servicing, observe the original lead dress. If a Some semiconductor (solid state) devices can be damaged short circuit is found, replace all parts which have been easily by static electricity. Such components commonly are over-heated or damaged by the short circuit.
  • Page 40 Memo...

  • Page 41: General Descriptions

    AG-1340P 1 GENERAL DESCRIPTIONS [2. HOW TO CONFIRM THE “NAVI.” DATA WITHOUT 1.1. SERVICE CAUTION-1 INSERTING A TAPE INTO VCR?] When the Microprocessor IC6001 and/or Back-up battery 1. Indicate the “NAVI” mark on the Front information Panel. B6001 are replaced, read following procedure carefully and (Press the Menu button and select the option, then set the proceed it.
  • Page 42 AG-1340P STEP 2. “NAVI” DATA BACK-UP PROCEDURE F.I.P. DISPLAY Turn on the Service Mode. 1. Press FF and EJECT keys simultaneously for more than 3 seconds. Turn on the Service Mode 2. 2. Press FF and EJECT keys in twice.

  • Page 43: How To Replace The Lithium Battery

    (See Fig.B1) Fig.B1 NOTE: The lithium battery is a critical component (Type No.:CR2354-1GUF Manufactured by Panasonic.) It must nerver be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.

  • Page 44: Service Caution-2

    AG-1340P 1.3. SERVICE CAUTION-2 1.3.1. CAUTION FOR AUTO TUNING PROCEDURE Auto Tuning will start by the following procedure. 1. Connect the DIN-RF Cable. 2. Connect the AC Mains Lead. 3. Turn on the VCR. Auto Tuning will start. Auto Tuning searches for TV stations from VHF minimum to UHF maximum and memorizes every tuned program position.
  • Page 45 AG-1340P Fig. S5 d. Rotate Main Cam Gear to the clockwise in order to eject the cassette tape. 1.3.4. CYLINDER UNIT REPLACEMENT 1. CYLINDER UNIT REPLACEMENT a. Remove the Mechanism unit from MAIN C.B.A./Chassis by referring “Disassembly Procedure”. b. Remove the 3 screws (A) of the CYLINDER UNIT with a screw driver.

  • Page 46: Self-Test & Service Information Display

    AG-1340P necessary. 1.3.5. FLAT CARD CABLE INSTALLATION When installing the Flat Card Cable on the connector, install the Flat Card Cable with the cable contacts facing the connector contacts. Fig. S8 c. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on Fig.

  • Page 47: Adjustment Procedures

    AG-1340P 2 ADJUSTMENT PROCEDURES 2.1. DISASSEMBLY METHOD 2.1.1. DISASSEMBLY FLOW CHART 2.1.2. DETAIL OF DISASSEMBLY METHOD This flow chart indicates disassembly steps of the cabinet parts and the circuit boards in order to find the necessary items for 1. REMOVAL OF THE TOP PANEL servicing.
  • Page 48 AG-1340P Fig. D5-2 5. REMOVAL OF THE MAIN C.B.A. Disconnect 4 Screws (H) Unlock 4 Tabs ( I ) Fig. D4 4. REMOVAL OF THE MECHANISM UNIT Remove 3 Screws (E) Remove 2 Screws (F) Remove Screw (G) NOTE: Keep pressing 2 stoppers on the Cassette Holder Plate and press the Cassette Holder Plate to the rear.

  • Page 49: Mechanical Adjustment Procedures

    AG-1340P 7. SERVICE POSITION Fig. D8 2.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. (Order No. VRD9802005C2)

  • Page 50: Electrical Adjustment Procedures

    AG-1340P 2.3. ELECTRICAL ADJUSTMENT PROCEDURES This section provides complete adjustment procedures 2.3.2. SERVO SECTION required for electric circuits of VCR. PG SHIFTER ADJUSTMENT 2.3.1. TEST EQUIPMENT PROCEDURES DISPLAY 1. To set Service Mode, press the FF and To perform electrical adjustments following equipment is EJECT keys simultaneously for more required.

  • Page 51: Abbreviations

    AG-1340P 3 ABBREVIATIONS...
  • Page 52 AG-1340P...
  • Page 53 AG-1340P...
  • Page 54 AG-1340P...

  • Page 55: Input/Output Chart

    AG-1340P 4 INPUT/OUTPUT CHART 4.1. INPUT/OUTPUT CHART FOR IC6001...
  • Page 56 AG-1340P...
  • Page 57 SYSTEM CONTROL & SERVO / TIMER SECTION BLOCK DIAGRAM :MAIN SIGNAL PATH IN REC MODE :MAIN SIGNAL PATH IN PLAYBACK MODE :CAPSTAIN SERVO SPEED LOOP :CAPSTAIN SERVO PHASE LOOP :CYLINDER SERVO SPEED LOOP :CYLINDER SERVO PHASE LOOP IC7501 TIMER IC6001 SYSTEM CONTROL & SERVO DP7501 TIMER DISPLAY POS.

  • Page 58: Video/Audio Section Block Diagram

    VIDEO/AUDIO SECTION BLOCK DIAGRAM :AUDIO MAIN SIGNAL PATH IN REC MODE :AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE :VIDEO MAIN SIGNAL PATH IN REC MODE :VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE X3001 TW3001 QR3011 PICT 2 TO/FROM SYSCON & SERVO Q3009 SECTION OSD VIDEO IN...

  • Page 59: Power Sction

    :TO SYSTEM CONTROL & SERVO / TIMER SECTION CAUTION MARK INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS. D1180 MAZ751000C D1181 T1150 G4D2A0000051 ZA1105...

  • Page 60: Syscon & Servo/Timer Section

    :VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :CAPSTAN SERVO PHASE LOOP :CYLINDER SERVO SPEED LOOP :VIDEO MAIN SIGNAL PATH IN REC MODE :CAPSTAN SERVO SPEED LOOP :CYLINDER SERVO PHASE LOOP <A-LINE> <A-LINE> (A14) (A15) (A17) (A11) (A19) (A28) (A29) (A31) (A32) (A15) (A14)
  • Page 61 :GRID CONTROL SIGNAL PATH SYSTEM CONTROL & SERVO ICs VOLTAGE CHART (SP MODE) :SEGMENT CONTROL SIGNAL PATH Ref.No. IC2501 MODE MODE SW <A-LINE> STOP 14.4 14.4 14.7 1.1 14.4 S2001 VSS0520-4 DP7501 PLAY 14.3 14.3 14.6 1.1 14.3 (A33) A2BD00000040 14.3 14.3 14.6 0.8 14.3 (A18)

  • Page 62: Video Section

    : VIDEO MAIN SIGNAL PATH IN REC MODE : AUDIO MAIN SIGNAL PATH IN REC MODE : VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE : AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE <A-LINE> <A-LINE> <A-LINE> :TO AUDIO SECTION (A8) (A9) (A7) (A10) (A6)
  • Page 63 <C-LINE> <12.0V> (C1) D A REC(H) Q4003 R4039 BIAS(L) 2SD1149 <5.0V> A/V 5.0V (4.7) (REC CONT.) (C1) <12.0V> 12.0V (C2) OSD CV IN (-27.0) 0.6(-27.3) (C2) <5.0V> R4037 (C4) PICT 2 4700 QR4001 UN2111 (C6) FSC IN (-18.1) R4038 (REC CONT.) 2200 (C8) <5.0V>...

  • Page 64: Audio Section

    : AUDIO MAIN SIGNAL PATH IN REC MODE : AUDIO MAIN SIGNAL PATH IN PLAYBACK MODE : TO VIDEO SECTION : VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE : TO SYSTEM CONTROL &SERVO SECTION : VIDEO MAIN SIGNAL PATH IN REC MODE LINE OUT LINE IN VIDEO...

  • Page 65: Main P.c.board (Vep06E21J)

    MAIN P.C.BOARD (VEP06E21J) MAIN P.C.BOARD Transistor Test Land Q1150 TL2015 Q1151 TL4507 Q1152 TL4552 Q1153 TL6001 Q1200 TL6010 Q1341 TL6012 Q2001 TL6013 Q2002 TL7509 Q3004 TL7510 Q3005 Q3009 PGND Q3010 Q4003 Test Wire Q4004 TW1004 Q4005 TW2001 Q4006 TW2002 Q4007 TW3001 Q4501 TW6001...
  • Page 66 Memo...

  • Page 67: Exploded Views & Replacement Parts List

    8 EXPLODED VIEWS & REPLACEMENT PARTS LIST SERVICING FIXTURES & TOOLS Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VFM8080HQFP VHS ALIGNMENT TAPE VFK0335 RETAINING RING REMOVER VFK0329 POST ADJ. SCREWDRIVER VFK0326 HEX WRENCH SET VFK0132A BACK TENSION METER...
  • Page 68 CHASSIS PARTS SECTION PRT-2...
  • Page 69 CHASSIS PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VHN0311 PUSH NUT VEG1537 CYLINDER UNIT VXP2026 UPPER CYLINDER UNIT 1 SUPPLIED FROM MAV VMX2208 CUT WASHER VDB1256 CYLINDER RETAINER W2,W3 VMX3022 WASHER VEK8840...

  • Page 70: Casing Parts Section

    CASING PARTS SECTION PRT-4...
  • Page 71 CASING PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VGM1802 TOP PANEL 1 SUPPLIED FROM MAV VYP8238 FRONT PANEL ASS'Y VKA0192 VKF3397 BLINDER PANEL 1 SUPPLIED FROM MAV VMB2521 BLINDER SPRING VKA0192 VJH1185 ANT BOARD...

  • Page 72: Packing Parts Section

    PACKING PARTS SECTION PRT-6...
  • Page 73 PACKING PARTS SECTION Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks VQT9136 OPERATING INSTRUCTIONS N2QAHB000010 REMOTE CONTROLLER K2KZ2BA00001 RF CABLE VJA0488 POWER CODE 1 K2CG3CH00001 VPN5359 CUSHION (L) VPN5360 CUSHION (R) VPG0J11 PACKING CASE 1 SUPPLIED FROM MAV PRT-7...

  • Page 74: Electrical Replacement Parts List

    9 ELECTRICAL REPLACEMENT PARTS LIST Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C3027 ECJ1VC1H270J C.CAPACITOR CH 50V VEP06E21J MAIN C.B.A. 1 (RTL) C3028 ECJ1VB1C104K C.CAPACITOR CH 16V 0.1U C3029 ECJ1VB1H103K C.CAPACITOR CH 50V 0.01U C3033 ERJ3GEY0R00 M.RESISTOR CH 1/16W...
  • Page 75 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C7706 ECJ1VC1H471J C.CAPACITOR CH 50V 470P L7601 G0C100JA0030 COIL 10UH C7707 ECJ1VB1H102K C.CAPACITOR CH 50V 1000P L7605 G0C100JA0030 COIL 10UH C7708 ECJ1VC1H471J C.CAPACITOR CH 50V 470P L7701 VLQ0599J5R6 COIL...
  • Page 76 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R2003 ERJ3GEYJ392 M.RESISTOR CH 1/16W 3.9K R6029 ERDS2TJ121 C.RESISTOR 1/4W 120 1 D0AE121JA045 R2004 ERJ3GEYJ222 M.RESISTOR CH 1/16W 2.2K R6030 ERDS2TJ181 C.RESISTOR 1/4W 180 R2006 ERJ3GEYG682 M.RESISTOR CH 1/16W 6.8K...
  • Page 77 Printed in Japan FCD0109TkSZN100...
  • Page 78 AG-1340P 2 ADJUSTMENT PROCEDURES 2.1. DISASSEMBLY METHOD 2.1.1. DISASSEMBLY FLOW CHART 2.1.2. DETAIL OF DISASSEMBLY METHOD This flow chart indicates disassembly steps of the cabinet parts and the circuit boards in order to find the necessary items for 1. REMOVAL OF THE TOP PANEL servicing.
  • Page 79 AG-1340P Fig. D5-2 5. REMOVAL OF THE MAIN C.B.A. Disconnect 4 Screws (H) Unlock 4 Tabs ( I ) Fig. D4 4. REMOVAL OF THE MECHANISM UNIT Remove 3 Screws (E) Remove 2 Screws (F) Remove Screw (G) NOTE: Keep pressing 2 stoppers on the Cassette Holder Plate and press the Cassette Holder Plate to the rear.
  • Page 80 AG-1340P 7. SERVICE POSITION Fig. D8 2.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. (Order No. VRD9802005C2)
  • Page 81 AG-1340P 2.3. ELECTRICAL ADJUSTMENT PROCEDURES This section provides complete adjustment procedures 2.3.2. SERVO SECTION required for electric circuits of VCR. PG SHIFTER ADJUSTMENT 2.3.1. TEST EQUIPMENT PROCEDURES DISPLAY 1. To set Service Mode, press the FF and To perform electrical adjustments following equipment is EJECT keys simultaneously for more required.
  • Page 82 9 ELECTRICAL REPLACEMENT PARTS LIST Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C3027 ECJ1VC1H270J C.CAPACITOR CH 50V VEP06E21J MAIN C.B.A. 1 (RTL) C3028 ECJ1VB1C104K C.CAPACITOR CH 16V 0.1U C3029 ECJ1VB1H103K C.CAPACITOR CH 50V 0.01U C3033 ERJ3GEY0R00 M.RESISTOR CH 1/16W...
  • Page 83 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks C7706 ECJ1VC1H471J C.CAPACITOR CH 50V 470P L7601 G0C100JA0030 COIL 10UH C7707 ECJ1VB1H102K C.CAPACITOR CH 50V 1000P L7605 G0C100JA0030 COIL 10UH C7708 ECJ1VC1H471J C.CAPACITOR CH 50V 470P L7701 VLQ0599J5R6 COIL...
  • Page 84 Ref.No. Part No. Part Name & Description Remarks Ref.No. Part No. Part Name & Description Remarks R2003 ERJ3GEYJ392 M.RESISTOR CH 1/16W 3.9K R6029 ERDS2TJ121 C.RESISTOR 1/4W 120 1 D0AE121JA045 R2004 ERJ3GEYJ222 M.RESISTOR CH 1/16W 2.2K R6030 ERDS2TJ181 C.RESISTOR 1/4W 180 R2006 ERJ3GEYG682 M.RESISTOR CH 1/16W 6.8K...

Table of Contents