All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by WO 0371 Service PaCE...
EN 2 FTP1.1E Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview 1.2.2 Index of this chapter: Audio receiver (if present) 1. Technical Specifications 2. Connections Audio - In (Cinch) 3. Chassis Overview C - Audio - Centre Note: Figures below can deviate slightly from the actual Audio - Out (Cinch) situation, due to the different set executions.
Page 4
Technical Specifications, Connections, and Chassis Overview FTP1.1E EN 3 Table 1-1 SCARTs overview Because this set is not equipped with a side I/O, a separate converter is added with the set. Use this SCART to cinch adaptor to connect temporary peripheral equipment Pin Signal Signal level Type...
Mechanical Instructions FTP1.1E EN 17 4. Mechanical Instructions Index of this chapter: heating, and/or falling. The stands can be mounted and 1. Service Positions removed quickly and easily with use of the provided screws, 2. Assy / PWB Removal which can be tightened and loosened manually without the use 3.
Page 19
EN 18 FTP1.1E Mechanical Instructions 4.2.3 Audio Amplifier Panel TWEETER LOUD SPEAKERS AUDIO AMPLFIER PANEL CL 36532075_052.eps 181103 Figure 4-5 SSB Box. Front view 1. Release the AC input cables from the Plasma Panel and SSB. EMC PANEL 2. Remove the two mounting screws (1) at the both sides of the SSB Box.
Via a standard customer RC-transmitter: key in “00”- (SAM) offer several features for the service technician, while sequence. the Customer Service Mode (CSM) is used for communication between a Philips Customer Care Centre (P3C) and a 5.2.2 Service Alignment Mode (SAM) customer.
Page 21
Name 8/30 F2 Broadcaster Name extracted from status development analysis, before initialising. This will give message of 8/30 Format 2. the Philips Service department an extra possibility for Name TXT Broadcaster Name extracted from TXT diagnosis (e.g. when Development asks for this).
Page 22
Service Modes, Error Codes, and Fault Finding FTP1.1E EN 21 • How to navigate VOLUME. Gives the last status of the volume as set by the • In SAM, you can select the menu items with the “CURSOR customer. The value can vary from 0 (volume is minimum) UP/DOWN”...
Page 23
EN 22 FTP1.1E Service Modes, Error Codes, and Fault Finding as one centre speaker. Change Centre mode via “MENU”, CUSTOMER SERVICE MENU 5 • “SETUP”, “SPEAKERS”, and “CENTRE MODE”. AVL. Indicates the last status of AVL (Automatic Volume • DNR. Gives the selected DNR setting (Dynamic Noise Level): “ON”...
Page 24
Introduction 5.4.3 Stepwise Start-up ComPair (Computer Aided Repair) is a service tool for Philips Under normal circumstances, a fault in the power supply, or an Consumer Electronics products. ComPair is a further error during start-up, will switch the television to protection development on the European DST (service remote control), mode.
Page 25
EN 24 FTP1.1E Service Modes, Error Codes, and Fault Finding ON/OFF switch to ON OTC gets supply voltage OTC resets, Initialise IO pins Read NVM identification enable watchdog start time extraction Stand-by stand-by bit = off t<500ms Step 1 t<250ms Activate MSP reset Put Stand-by line LOW Keep sound amplifiers muted with...
Page 26
Service Modes, Error Codes, and Fault Finding FTP1.1E EN 25 Note (*): Error Codes • When the set is in stepwise mode and, due to stepping-up, a protection is activated, the set will really go into protection 5.5.1 Introduction (blinking LED). The set will not leave the stepwise-mode however.
Page 27
EN 26 FTP1.1E Service Modes, Error Codes, and Fault Finding 5.6.2 Table 5-2 Error Code Table How to Enter Def. Def. Module Use one of the following methods: Error Device Description item indication Diagr. • Enter the SDM (only via soldering pads marked “SDM” on M24C32 NVM, 7011 Control...
Page 28
Service Modes, Error Codes, and Fault Finding FTP1.1E EN 27 5.8.2 There are several types of protections: ComPair • I2C related protections. • OTC related protections (via polling on I/O pins or via This chassis does not have an IR transmitting LED (as in MG- algorithms).
Page 29
EN 28 FTP1.1E Service Modes, Error Codes, and Fault Finding Table 5-3 Repair tips Phenomenon Possible Cause Repair tip No picture, LED blinking at 3 Hz. Set is in protection due to various causes. You have no picture, so: For error codes see error-code list. Read the error buffer via ComPair (error buffer is accessible when set is in protection, compare- file will guide you to this) Read the blinking LED information via standard remote command <mute>06250x<ok>.
Page 30
Electrical Alignments FTP1.1E EN 89 8. Electrical Alignments • Index of this chapter: Use an isolated trimmer/screwdriver to perform 1. General alignment conditions alignments. 2. Hardware alignments 3. Software alignments 8.1.2 Initial Settings 4. Option settings Perform all electrical adjustments with the following initial settings (via the "Active Control"...
Page 31
EN 90 FTP1.1E Electrical Alignments Notes: Table 8-2 2fH ADC alignment • All changes must be stored manually. • If an empty EAROM (permanent memory) is detected, all Menu item Alignment value settings are set to pre-programmed default values. RED GAIN RGB BLUE GAIN RGB 8.3.1 GENERAL...
Page 32
Electrical Alignments FTP1.1E EN 91 8.3.4 LUM. DEL. transients of the colour and black and white part of the test area are at the same position. Default value is "6". With this Luminance Delay alignment, you place the luminance information exactly on the chrominance information (brightness Option Settings is pushed onto the colour).
Page 33
Set without Home Cinema Link Integrated RC Feature present. Feature not present. Tuner type UV1316 Set with Philips tuner. TEDE9 Set with Alps tuner. P50 DVD menu line Sets with Home Cinema Link (EU only). Sets without Home Cinema Link.
Page 34
Electrical Alignments FTP1.1E EN 93 Table 8-8 Option bytes Group 1 Byte nr. Bit nr. Decimal value Option name Settings (in decimal values) Option Byte value Featurebox 0= None (n.a.) 2= Prozonic (n.a.) 3= Eagle 4= Falconic (n.a.) 5= Falconic+ (n.a.) 2D Comb Filter 0= Off 8= On...
Page 35
EN 94 FTP1.1E Electrical Alignments Table 8-9 Option bytes Group 2 Byte nr. Bit nr. Decimal values Option name Settings (in decimal values) Option Byte value n.a. Auto Store Mode 0= None (US/LA/AP-N) 2= PDC/VPS (EU) 4= TXT Page (EU) 6= PDC/VPS/TXTpage (EU) n.a.
Page 36
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 95 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: Further features of the SSP are: 1. Introduction • The 3D Comb filter functionality (for USA) is integrated on 2.
Page 37
EN 96 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets TO PDP PANEL LVDS DC/DC CONVERTER AUDIO PROC. FBX (2FH) PIXEL PLUS LVDS DW/PIP EPLD HIP 2 HIP1 MAIN TUNER VGA/RGB CINCH CINCH SCART SCART HEADPHONE SERVICE ANTENNA (EXT5) (AUDIO) (EXT1/2) (EXT3/4)
Page 38
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 97 Block Diagram VIF OUT MAIN SCART2 MAIN CVBS pip cvbs CVBS PIP OUTmain cvbs int Y/Cvbs ext 1/4 main cvbs 1 CVBS 1 read_status 1 2FH/3FH STATUS INPUTS rgb ext 1 YUV1fH fbl ext 1 FBL 1...
Page 39
EN 98 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.3.1 Power Balance Events in SEMI-STANDBY 1. The set can be in semi-standby during Time extraction, EPG loading, or P50 (Easylink) recording. The semi- Table 9-1 Total power balance overview standby state is ended when: –...
Page 40
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 99 Note: The SCART input (1fH) path is equal to the one described in the EM6E manual. Therefore, it is not described in much detail here. 9.4.2 Input detection The RGB or YPbPr input signals (2fH/3fH) are sent to the ADC (AD9883A) together with H and V pulses from DVI (USA) or VGA (EUR), and the Y signal from YPbPr called Sync On Green (green is same line as Y).
Page 41
EN 100 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets 2fH/3fH input flow Selection AV5 or AV6 Eur START AV4 or AV5 US Put ADC: full power Mute sound, Blank picture wait 200 msec AV4 on US ? 1Fh detection in HIP? Put picnic: freerun ON Put picnic to 1FH Put ADC on last status from select.
Page 42
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 101 1. The standard detection starts with a 2fH/3fH selection (this 8. If the ADC has not the right settings, the PLL does not lock, is AV5 / AV6 in Europe or AV4 / AV5 in USA). and the "STDET"...
Page 43
EN 102 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets – CVBS outputs, being: CVBS PIP/DS, CVBS_TXT_OUT for Contrast reserve (peak limiter), – comb filter (always following YUV main!) and TXT Sync wheel, – processing, and the CVBS/Y_RECORD_OUT for EXT2. Dithering (matrix displays are 8 bit), –...
Page 44
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 103 Table 9-6 AV6 (VGA) input signals AV6 Inputs System Field freq. (V) Line freq. (H) (VGA) 640x480 60 Hz 31.5 kHz SVGA 800x600 56 Hz 35.1 kHz 576 p 50 Hz 31.25 kHz 480 p...
Page 45
EN 104 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets • Auto TV For USA: – The Auto Picture Control or in short AutoTV, aims at providing AV1. – the customer the best possible picture performance at any AV2. –...
Page 46
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 105 9.6.5 Audio Amplifier Panel (Diagram A) High Pass Filter (HPF) For L and R separately, a High Pass Filter (IC7260A and B) is processing L_HIGH and R_HIGH. Introduction The output signal of this filter is then fed to the audio amplifier (identical for right channel).
Page 47
EN 106 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets Protections Short-circuit Protection (e.g. Diagram A3 for "Left High") A protection is made against a too high temperature of transistor 7355 in case of a short-circuit of output FET 7365-1. Transistor 7340 is sensing the current through transistor 7355 via R3355, and activates the DC-protection line (see below) in case the current becomes too high.
Page 48
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 107 Synchronisation 9.7.1 Introduction Through the chassis, the synchronisation is complicated because the PDP display needs another number of pixel per line (852) and lines per frame (480). Therefore, there is a different sync flow for 1fH, 2fH, or 3fH inputs.
Page 49
EN 108 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets • The Eagle delivers a clock signal for the FALCONIC and Table 9-7 LED control the field memories. • The Eagle delivers a 64MHz clock to the EBILD (CLK64). Condition Two colour LED Green...
Page 50
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 109 – of the OTC the same way the +8V protection is Feasible up to VGA/NTSC resolution (limited to 250 implemented. The set must also go into protection. Mb/s). • LVDS –...
Page 51
EN 110 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets Advantages: Data Memory Space Code Memory Space • Flexibility. • No change in internal ROM (IROM) required (IROM not used). XRAM (2MB) • Flexibility to change of code flash manufacturer as the "flash driver"...
Page 52
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 111 9.12 Abbreviation list START 0/6/12 SCART switch control signal on A/V board. 0 = loop through (AUX to TV), 6 = play 16:9 format, 12 = play 4:3 Clear EPG flash format 2DNR Spatial (2D) Noise Reduction...
Page 53
EN 112 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets Digital Versatile Disc LATAM Latin America DVI(-d) Digital Visual Interface (d= digital only) Liquid Crystal Display Eagle Feature box IC performing peaking, Light Emitting Diode zooming and subpixel LTI in both L/L' Monochrome TV system.
Page 54
4.406250 MHz and 4.250000 MHz Sound Intermediate Frequency SMPS Switched Mode Power Supply Sync On Green SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board Small Signal Panel STBY STandBY SUB_Y/U/V_2FH Y/U/V input from I/O cel...
Page 55
EN 114 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.13 IC Data Sheets This section shows the internal block diagrams and pin layouts of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic" ICs). 9.13.1 Diagram B3C, T8F24EF (IC7724) Bus formats 8u@32MHz - 8 bits unsigned data at 32 MHz...
Page 56
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 115 9.13.2 Diagram B14A, TEA6415 (IC7I24) BLOCK DIAGRAM PERI PERI LUMA CHROM A DEC. POWE R CVBS (MAC/DEC ) CV BS (PERI PLUG1 ) CVBS (AM TUNER ) MAC SIGNAL (AM TUNER ) CV BS (PERI PLUG2 )
Page 57
EN 116 FTP1.1E Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.13.3 Diagram B16DE, MC1496D (IC7H40, 7H50, 7H60) EQUIVALENT SCHEMATIC CARRIER (±) INPUT (+) SIGNAL (±) INPUT (+) GAIN ADJUST BIAS 500kΩ 500kΩ 500kΩ V± PIN CONFIGURATION F, N Packages POSITIVE SIGNAL INPUT GAIN ADJUST...
Page 58
Circuit Descriptions, Abbreviation List, and IC Data Sheets FTP1.1E EN 117 9.13.4 Diagram B19E, AD9066JR (IC7E09, 7E16) FUNCTIONAL BLOCK DIAGRAM AD9066 6-BIT D0A-D5A REF A ENCODE 6-BIT D0B-D5B REF B PIN CONFIGURATIONS ENCODE D5A (MSB) REF A REF B AD9066 AD9066 D0A (LSB) (JR/AR)
Page 59
EN 118 FTP1.1E Spare Parts List 10. Spare Parts List Set Level 2460 2020 012 93764 220µF 20% 35V 3308 4822 117 13632 100kΩ 1% 0.62W 0603 2465 2020 552 96326 220nF 10% 16V 3309 4822 051 30181 180Ω 5% 0.062W 2466 2020 552 96326 220nF 10% 16V 3310...
Page 112
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Top Side Overview) Part 2 CL 36532075_44b.eps Part 1 CL 36532075_44a.eps Part 3 CL 36532075_44c.eps Part 4 CL 36532075_44d.eps 3104 303 3879.2 CL 36532075_044.eps 061103...
Page 114
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Top Side Part 1) Part 1 CL 36532075_44a.eps 061103...
Page 115
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Top Side Part 2) Part 2 CL 36532075_44b.eps 061103...
Page 116
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Top Side Part 3) Part 3 CL 36532075_44c.eps 061103...
Page 117
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Top Side Part 4) Part 4 CL 36532075_44d.eps 061103...
Page 118
Circuit Diagrams and PWB Layouts FTP1.1E Layout Small Signal Panel (Bottom Side Overview) Part 2 CL 36532075_45b.eps Part 1 CL 36532075_45a.eps Part 4 CL 36532075_45d.eps Part 3 CL 36532075_45c.eps 3104 303 3879.2 CL 36532075_045.eps 061103...
Need help?
Do you have a question about the 42PF9945 and is the answer not in the manual?
Questions and answers