This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage.
Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: •...
• Check for obvious damage to a hard disk drive. If the spindle of a hard disk drive becomes noisy, the hard disk drive might have been dropped or subject to excessive force. CRU list Table 1. Model: Lenovo Slim 7 ProX 14IAH7 (MT: 82V1) Type ac power adapter...
Chapter 4. Removing a FRU or CRU Service tools The following table lists tools for servicing Lenovo computers. Tools with a cross mark are needed for serving the product models as described by this publication. Prepare them before you service the product.
3. Follow the correct sequence in the steps for removing an FRU, as shown in the illustrations by the numbers in square callouts. 4. When removing an FRU, move it in the direction as shown by the arrow in the illustration. 5.
Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Lower case Remove the battery pack Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 32 Step 1.
Screw specifications Number of screws M2 x L1.8 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Speakers Remove the touchpad cable Make sure the following FRUs (or CRUs) have been removed. “Remove the lower case” on page 32 “Remove the battery pack”...
Disconnect the CMOS battery cable from the system board. Step 2. Remove the CMOS battery. Figure 8. Remove the CMOS battery Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: CMOS battery Remove the solid-state drive (SSD) module Make sure the following FRU (or CRU) has been removed.
Figure 9. Remove the SSD Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Solid-state drive (SSD) Remove the heat sink Make sure the following FRU (or CRU) has been removed. “Remove the lower case” on page 32 Step 1.
Figure 11. Remove the fans Screw specifications Number of screws M2 x L3.5 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Fans Remove the Type-C bracket Make sure the following FRU (or CRU) has been removed.
Figure 12. Remove the Type-C bracket Screw specifications Number of screws M2 x L3.5 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Type-C bracket Remove the Wi-Fi card Make sure the following FRU (or CRU) has been removed.
Figure 13. Remove the Wi-Fi card Screw specifications Number of screws M2 x L1.8 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Wi-Fi card Remove the I/O board shielding and the I/O board Make sure the following FRUs (or CRUs) have been removed.
Screw specifications Number of screws M2 x L2.7 Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: I/O board I/O board shielding Remove the system board and the I/O board cable Make sure the following FRUs (or CRUs) have been removed.
Figure 15. Remove the I/O board cable Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: System board I/O board cable Use a Golden Key U1 tool to flash-write key id information After replacing the system board and re-assembling the computer, use a pre-made Golden Key U1 tool to start the computer and flash-write the serial number (SN), machine type (MT), product name (PN), and UUID to the new system board.
“Remove the system board and the I/O board cable” on page 40 “Remove the LCD module” on page 41 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Upper case Disassemble the LCD module The LCD module as a whole is not an FRU.
Step 1. Remove the hinge cover. Figure 17. Remove the hinge cover Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: Hinge cover Remove the hinge Make sure the following FRUs (CRUs) have been removed.
Figure 19. Remove the strip cover Screw specifications Number of screws M1.2 x L2.4 Go to to look up the Lenovo part number of the following replacement https://support.lenovo.com/partslookup part: Strip cover Remove the LCD bezel Make sure the following FRU (CRU) has been removed.
Note: The removable tape are not reusable. Replace them when replacing related FRUs. Figure 21. Remove the LCD panel Go to to look up the Lenovo part numbers of the following https://support.lenovo.com/partslookup replacement parts: LCD panel Removable tape Remove the EDP cable Make sure the following FRUs (CRUs) have been removed.
Step 1. Remove the camera rubber. Figure 23. Remove the camera rubber Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: Camera rubber Removable tape Remove the camera cable Make sure the following FRUs (CRUs) have been removed.
Figure 24. Remove the camera cable Go to https://support.lenovo.com/partslookup to look up the Lenovo part numbers of the following replacement parts: Camera cable Removable tape Remove the camera board Make sure the following FRUs (CRUs) have been removed. “Remove the LCD module” on page 41 “Remove the hinge cover”...
Page 54
“Remove the camera rubber” on page 46 “Remove the camera cable” on page 46 “Remove the camera board” on page 47 Go to https://support.lenovo.com/partslookup to look up the Lenovo part number of the following replacement part: LCD cover Hardware Maintenance Manual...
Need help?
Do you have a question about the Slim 7 Pro X and is the answer not in the manual?
Questions and answers