Table of Contents
Advertisement
Quick Links
Flashing LED Beacon Kit
LT2240 Compact Triple 4-Wheel Drive Turf Mower, LT3340 Triple
Reel Mower, or LT-F3000 Triple Flail Mower
Model No. 02856—Serial No. 400000000 and Up
Preparing to Install the
Flashing Beacon Kit
Preparing the Machine
1.
Park the machine on a level surface.
2.
Lower the cutting units.
3.
Engage the parking brake.
4.
Shut off the engine and remove the key.
5.
Wait for all moving parts to stop.
6.
Allow the engine to cool completely.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Removing the Storage
Compartment
Models 31657 and 31659
Opening the Hood
Model 31654
Register at www.Toro.com.
1.
At the left side of the operator's platform, open
the door of the storage compartment
Figure 1
1. Washer
2. Knob
2.
Remove the 3 knobs and 3 washers that secure
the storage compartment to the machine, and
remove the compartment
1.
Insert the hood key into the lock for the hood and
rotate the lock 90° counterclockwise
2.
Release the hood latch by pressing the button
on the hood latch
(Figure
Original Instructions (EN)
Printed in the UK
All Rights Reserved
Form No. 3443-338 Rev A
Installation Instructions
(Figure
3. Storage compartment
(Figure
1).
(Figure
2).
*3443-338*
1).
g328513
2).
Advertisement
Table of Contents
Related Manuals for Toro 02856
Summary of Contents for Toro 02856
- Page 1 Form No. 3443-338 Rev A Flashing LED Beacon Kit LT2240 Compact Triple 4-Wheel Drive Turf Mower, LT3340 Triple Reel Mower, or LT-F3000 Triple Flail Mower Model No. 02856—Serial No. 400000000 and Up Installation Instructions Preparing to Install the Removing the Storage...
-
Page 2: Disconnecting The Battery
Insert the hood key into the lock for the hood and rotate the lock 90° counterclockwise. Carefully rotate the hood back and down (Figure g189331 Figure 2 Carefully rotate the hood back and down (Figure g036763 Figure 5 Disconnecting the Battery Loosen the forward nut of the negative g189330 Figure 3... -
Page 3: Installing The Kit
Removing the Bulkhead Panel If a road light is installed on the machine, disconnect the 2 pin connector from the number plate. Remove the 4 bolts (6 x 25 mm), 4 lock washers (6 mm), and 4 flat washers (6 mm) that secure the bulkhead panel to the chassis of the machine (Figure g344020... - Page 4 g344042 Figure 11 1. Beacon stand 4. Ferrite 5. Beacon cable 2. Seal 3. Nut To fit the beacon cable, start by removing the fitting in the top of the beacon stand and feed the beacon cable through the bottom and out through the top.
- Page 5 • On model 31654, the mating connector is located near the horn. • On models 31657 and 31659, the mating connector is located under the plastic bulkhead at the bottom of the right ROPS post. Insert a cable tie through each of the 2 holes in the beacon bracket (Figure 15), and secure...
-
Page 6: Installing The Switch
the beacon cable through the bottom and out through the top. Connect the beacon cable, ensuring that the red connector is fitted to the central positive terminal of the beacon stand fitting, and the brown connector to the outer terminal. Screw the fitting back into the beacon stand. -
Page 7: Completing The Installation
Completing the Installation Installing the Bulkhead Panel Align the 4 holes in the bulkhead panel with the 4 clip nuts on the chassis; refer to Figure 7 Removing the Bulkhead Panel (page Secure the bulkhead panel to the chassis of the machine with the 4 bolts, 4 lock washers, and 4 flat washers;... -
Page 8: Connecting The Battery
Model 31654 Remove the fuse-block cover (Figure 24). Note: On model 31654, the fuse block is located behind the seat under the engine cover. g037069 g328512 Figure 24 Figure 26 1. Fuse-block cover 1. Washer 3. Storage compartment 2. Knob Install the fuse in the slot in the fuse block located at the 3rd position from the right (Figure... -
Page 9: Operation
Operation Using the Beacon To turn on the beacon, press the bottom of the switch. To shut off the beacon, press the top of the switch. Note: The ignition switch must be in position 1 for the beacon to work. g188128 Figure 29 Maintenance... - Page 10 g328465 Figure 31 Install the fuse-block cover. Install the storage compartment; refer to Installing the Storage Compartment (page...
- Page 11 Notes:...
- Page 12 Notes:...
- Page 13 Notes:...
- Page 14 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 15 Countries Other than the United States or Canada Customers should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.
Need help?
Do you have a question about the 02856 and is the answer not in the manual?
Questions and answers