All parts of this document are the property of Saeco International Group.
All rights reserved. This document and all the information herein is provided without liability deriving from any errors or omissions. Furthermore, no part may be reproduced, used or
collected, except where express authorisation has been provided in writing or through a contractual agreement.
Published by Saeco International Group
Super automatic espresso coff ee machine
3100 series
USER MANUAL
Read carefully before using the machine.
Register your product and get support at
www.philips.com/welcome
Service Manual
Value
Thermoplastic material
215mm x 330mm x 429 mm
6.7 kg for CMF-AMF 7.5 Kg for OTC (data may vary depending on the model)
Page 1
3100 series HD8831 USER MANUAL HD8834 USER MANUAL HD8832 PHILIPS 3100 CMF-AMF-OTC USER MANUAL Read carefully before using the machine. Read carefully before using the machine. Read carefully before using the machine. Service Register your product and get support at Register your product and get support at www.philips.com/welcome...
PHI 3100 01 INTRODUCTION Documentation required The following documentation is needed for repair procedures: • Instruction booklet for specific model • Technical documentation for specific model (diagrams, exploded view, sympton cure and service manual) Tools and resources As well as the standard equipment, the following is required: Qty.
Page 5
PHI 3100 01 INTRODUCTION Simply turning off the main machine power switch is not an adequate safety precaution. This domestic appliance is rated as insulation class I. On completion of the repair work, insulation and dielectric rigidity tests must be performed.
PHI 3100 01 INTRODUCTION Service POLICY grid as used for coffee machines For IN WARRANTY repairs is raccomanded to use when and where possible the single compo- nents,available in the exploded views of the coffee machines or of the specific components. If you find the information “SEE THE EXPLODED VIEW E..”...
Page 12
PHI 3100 02 TECHNICAL SPECIFICATION 2.1. Technical specifications Power supply and output: 240 V~ 50 Hz 1850 W - 230 V~ 50/60 Hz 1850 W 120 V~ 60 Hz 1500 W Temperature monitoring: (NTC) variable resistor sensor - transmits the value to the electronic card Safety system: 2 thermostats at 190°C one shot...
PHI 3100 02 TECHNICAL SPECIFICATION 2.2. Machine parameters and performance Programm. by PRODUCT Default quantity User Production / QUANTITY (Grams) programmable Service Espresso 40 +/- 10gr Espresso lungo 120 +/- 10% Hot water Continues until the water supply has been exhausted (capacitive sensor) Steam pannarello Continues until the water supply has been exhausted (capacitive sensor)
PHI 3100 02 TECHNICAL SPECIFICATION 2.3. Specification for the measurement of the coffee products temperature. The temperature is influenced by the flow from the dispenser and stratification of temperatures in the glass. In order to consider these phenomena and to introduce measures that allow comparisons in controlled conditions, below guidelines must be followed: Conditions: a) Water temperature in tank: 23°C (+/-2°C).
PHI 3100 02 TECHNICAL SPECIFICATION 2.3.1. Specification for the measurement of the Milk products temperature. Milk evaluation To carry out the test, a partially skimmed UHT milk with a percentage of grease between 1.5-1.8% at a refrigerator temperature Trefr. (between 4 to 10°C) must be used. The milk product must be checked on a beaker of 250 ml of capability and with an inner diameter of 70mm, brewing 100gr of product.
Page 16
PHI 3100 02 TECHNICAL SPECIFICATION How to measure the milk cream. The temperature (Trefr or Tamb) of the milk doesn’t affect as much the test result on measuring the milk cream; by convection is assumed to always use milk at refrigerator temperature Trefr.. Manual systems (Pannarello) Pour 100cc.
PHI 3100 03 BRIEF INSTRUCTIONS 3.1. Customer menu PHI 3100 CMF Control Panel Espresso brew button Steam button Long espresso brew button Hot water buttonutton “Aroma” - Pre-ground Descaling button coffee button ON/OFF button 3.2. Meaning of the display icons This machine is equipped with a colour-coded system to make your understanding of the display signals easier.
Page 19
Turn it back on after 30 seconds. Try this 2 or 3 times. For error codes 1 -3 - 4 - 5. If the machine does not start, contact the Philips hotline in your country and quote the error code shown on the display. Contact details can be found in the warranty booklet...
PHI 3100 03 BRIEF INSTRUCTIONS 3.3. Customer menu PHI 3100 AMF Control Panel Espresso brew button Steam button Long espresso brew button Hot water buttonutton “Aroma” - Pre-ground MENU button coffee button ON/OFF button 3.4. Meaning of the display icons This machine is equipped with a colour-coded system to make your understanding of the display signals easier.
Turn it back on after 30 seconds. Try this 2 or 3 times. If the machine does not start, contact the Philips hotline in your country and quote the error code shown on the display. Contact details can be found in the warranty booklet packed separately or at www.
PHI 3100 03 BRIEF INSTRUCTIONS 3.6. Meaning of the display icons This machine is equipped with a colour-coded system to make your understanding of the display signals easier. The icons are colour-coded according to the traffic light principle. Ready Signals (Green Colour) STOP The machine is ready to brew The machine is frothing milk for...
Page 23
Turn it back on after 30 seconds. Try this 2 or 3 times. If the machine does not start, contact the Philips hotline in your country and quote the error code shown on the display. Contact details can be found in the warranty booklet packed separately or at www.
Page 24
PHI 3100 03 BRIEF INSTRUCTIONS Machine actions Causes Solution Error Code 1 Coff ee outlet duct Thoroughly clean the coffee outlet Coffee grinder blocked. clogged. duct. Close the service door. Turn off and Error Code 3-4 The brew group is out of back on the machine.
Page 25
PHI 3100 03 BRIEF INSTRUCTIONS Machine actions Causes Solution The brew group is not in Make sure that the brew group in the the off position. off position. Insert the drip tray and the coffee The brew group cannot be grounds drawer.
Page 26
PHI 3100 03 BRIEF INSTRUCTIONS Machine actions Causes Solution Clean the hole of the steam wand using a pin. The hole of the steam/hot Make sure that the machine is off water wand is clogged. and has cooled down before per- No hot water or steam is forming this operation.
PHI 3100 04 OPERATING LOGIC 4.2. Milk Carafe PHI 3100 OTC 1) Steam input 2)Bring the cappuccino maker into dispensing position 3) Milk tank The milk is heated by the steam and taken towards the Steam emulsion chamber where it is mixed with air and trans- formed into foam The steam passes through the...
PHI 3100 04 OPERATING LOGIC 4.3. Single microswitch Switching on When the machine is switched on, the gear motor repositions itself as follows: - It acts on microswitch 1 - The gear motor changes its rotation direction and moves upwards again by approx. 1-2 mm. - The boiler begins to heat the water for approx.
PHI 3100 04 OPERATING LOGIC 4.4. Coffee grinder Philips 3100 The coffee grinder is driven by a direct current motor (1) using a worm screw helicoidal wheel transmission (2). The worm screw (2) drives a plastic gear wheel (3), which turns the lower grinder (4) and the increment pin (5) There are two magnets (6) in the gear wheel;...
PHI 3100 04 OPERATING LOGIC 4.4.2. Dose self-learning (SAS) The aim of this function is to automatically regulate the average dose of ground coffee (SELF-LEARN- ING); this takes place with an algorithm based on the following values and setting by the user: 1.
PHI 3100 04 OPERATING LOGIC 4.5. Coffee cycle Main switch ON START STOP Time Coffee grinder Time (Dosage) Heating approx. 45 sec. Pump Pump operation (flow meter pulses) in accordance with the amount of product selected. Brewing unit gear motor Status Heating Ready...
PHI 3100 04 OPERATING LOGIC 4.6. Water level detection (water tank) “Water low” message (water reserve) Function: Water tank The water level is monitored by a capacitative sensor, located one third of the way up the water tank wall. If the electronics assembly detects, by means of the sensor, that the amount of water in the tank has dropped below the above mentioned Sensor level, a water reserve remains available for the dispensing process...
PHI 3100 04 OPERATING LOGIC 4.8. Water filter Function: • Reduced limescale deposits which take longer to form. • Improved water quality. • Improved taste due to the ideal water hardness. Life span / descaling performance: • - 10 ° dH •...
Test Mode PHI 3100 Introduction This document describes the Test Mode of the Philips 3100 (CMF,AMF & OTC) Coffee Machine. This application is used in order to test the machine in its mechanics and electronic components. To enter Test Mode The machine enters in Test mode by holding pressed together Z1 and Z6 buttons while switching on the machine by the main switch on the backside of the CA.
Page 38
Pressing button Z7 TEST MODE Level 3 Pressing button Z7 TEST MODE Level 4 Pressing button Z7 TEST MODE Level 5 Filename Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 1.1 Page 0 (FIRMWARE) Filename Filename Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 1.1 Page 0 (FIRMWARE)
Page 40
Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 1.3 Page 2 (INPUTS) Start condition 1.3 Page 2 (INPUTS) Filename Start condition 1.3 Page 2 (INPUTS) Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 PHI 3100 05 SERVICE MODE Start condition 1.3 Page 2 (INPUTS) Insert a full Water Tank...
Page 41
Filename display backlight changes from green to red; check the BU a nd the motor Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 motor ERROR: (With BU)The absorbed current is more than 300mA, the display Test Mode Philips 3100 Test Mode Philips 3100...
Page 42
CPU/POWER board (JP5). If no water comes out the pipe: Filename to the CPU/POWER board (JP24). to the CPU/POWER board (JP24). Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 check the pump and the wiring from the pump to the CPU/POWER board (JP24).
CPU/POWER board (JP13). green to red; check the wiring from the NTC temperature-sensor to the Filename Filename CPU/POWER board (JP13). Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 Test Mode Philips 3100 20150423_Philips3100_TestMode_v01 Press the Z1 button to switch on the Heater...
Page 44
sensor must work correctly; if some errors occurs on Ntc during t steam-out, the procedure can’t continue and an error me ssage is shown on the display. IMPORTANT NOTE: to execute the Steam-Out procedure the PHI 3100 05 SERVICE MODE DREGDRAWER must be in place and the DOOR must be closed.
PHI 3100 05 SERVICE MODE 5.3. Error codes ERROR DESCRIPTION CODES The coffee grinder is blocked (grinder blades jammed or sensor not reading properly) The brewing unit is blocked in work position (microswitch not released in up position after 3", torque error trying to move down, descent time out exceeded) The brewing unit is blocked in home position (microswitch not released in down position after 3", torque error trying to move up, ascent time out exceeded) Water circuit / flow meter problems (water circuit blocked or no flow meter signal)
Final inspection test 13 Steam out before shipping out, if temperature is below 0° to prevent any demaged due to frozen water. No need for those families Minuto family (all platform); Incanto family new; Pico Baristo; 14 Gran Baristo; Intelia V2; Philips 2000‐2100; Incanto Executive; Moltio family (all platform). Please also check for GDA_113455 Provide precise IRIS code, according dedicated code table for Coffee products. The location code from the part you have worked on MUST be completed always with the part 15 ...
Page 48
Grinder Is the grinder noise normal Steam Steam Does the steam work Hot Water Does the hot water work PHI 3100 06 SERVICE AND MAINTENANCE Milk (if applicable) Cappuchino Does the cappuccinatore produce good froth Leakage Leakage 14 Did the product leak during the testing 15 Draining the circuit (in winter) ...
PHI 3100 07 DISASSEMBLY 7.2. Coffee grinder When reassembling coffee grinder, make sure the spring is repositioned cor- rectly (see photo). Raise the coffee grinder and remove the connections. The new machines have a coffee grinder with the screw to prevent the dis- assembly of the upper coffee grinder support (see photo).
PHI 3100 07 DISASSEMBLY Adjustment by a service center To adjust grinding further, the engineer can work directly on the coffee grinder by pressing and turning the ring nut (C) shown. (clockwise to increase the particle size of the coffee and anticlockwise to decrease it).
PHI 3100 07 DISASSEMBLY 7.6. Central plate unscrew the screws shown Lift up the center plate 7.7. Pin boiler Loosen the screws as illustrated and remove the boiler pin (A).
PHI 3100 07 DISASSEMBLY 7. 8. Gear motor Loosen the screws as illustrated and remove the gear motor cover. The following are located inside the compartment protected by the casing: - Electric motor (A) with gears (B) and (C) for transmission and timing of the dispenser.
PHI 3100 07 DISASSEMBLY 7.9. Pump Unhook the pump from the supports. Disconnect the water circuit connections (A) and electrical connections (B), loosen the safety valve (C) and slide the pump off the brackets (D). 7.10. Flow-meter Lift the flow meter out of the casing assembly and remove the electrical and water circuit connections. 7.11.
PHI 3100 07 DISASSEMBLY 7.12. CPU board Loosen the screws slide the card off the support and disconnect the electrical connections. 7.13. Programming access for SSC (Saeco Service Center) Loosen the screw for remove the cover. 7.14. KYB interface and display Remove the cover.
PHI 3100 07 DISASSEMBLY 7.15. Fitting and removing Oetiker clamps 1) Boiler connection 2) Other connections Replacing the hoses 1) Use a suitable pair of pliers to remove the clamp (as illustrated) 2) Tighten the clamp as illustrated...
Need help?
Do you have a question about the 3100 CMF-AMF-OTC and is the answer not in the manual?
Questions and answers