Table of Contents
Advertisement
Quick Links
ROPS Kit
Model No. 144-1848
Model No. 144-1849
Safety
Rollover Protection System
(ROPS) Safety
•
The ROPS is an integral safety device. Do not
remove any of the ROPS components from the
machine.
•
Ensure that the seat belt is attached and that you
can release it quickly in an emergency.
•
Keep the roll bar in the fully raised and locked
position and always wear your seat belt whenever
the roll bar is up.
•
Check carefully for overhead objects before you
drive under them, and do not contact them.
•
Replace damaged ROPS components. Do not
repair or alter them.
•
There is no rollover protection when the roll bar
is down.
•
Wheels dropping over edges, over steep banks, or
into water can cause a rollover, which may result
in serious injury or death.
•
Do not wear the seat belt when the roll bar is down.
•
Lower the roll bar only when absolutely necessary;
raise it as soon as clearance permits.
•
In the event of a rollover, take the machine to an
Authorized Service Dealer to inspect the ROPS.
•
Use only Toro approved accessories and
attachments for the ROPS.
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Safety and Instructional
Decals
Register at www.Toro.com.
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
107-3069
1. Warning–there is no rollover protection when the roll bar is
down.
2. To avoid injury or death from a rollover accident, keep the
roll bar in the raised and locked position and wear the seat
belt. Lower the roll bar only when absolutely necessary; do
not wear the seat belt when the roll bar is down.
3. Read the Operator's Manual; drive slowly and carefully.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3441-499 Rev A
Installation Instructions
decal107-3069
*3441-499*
Advertisement
Table of Contents
Related Manuals for Toro 144-1848
Summary of Contents for Toro 144-1848
- Page 1 • In the event of a rollover, take the machine to an Authorized Service Dealer to inspect the ROPS. • Use only Toro approved accessories and attachments for the ROPS. decal107-3069 107-3069 1. Warning–there is no rollover protection when the roll bar is down.
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the existing rollover protection – No parts required system (ROPS). Upper roll bar assembly Left lower roll bar assembly Right lower roll bar assembly Fold-pin assembly... - Page 3 Removing the Existing Rollover Protection System (ROPS) No Parts Required Procedure Disconnect the negative battery cable. Remove and discard the upper roll-bar tube and its hardware from the lower tubes. On the left side of the machine, remove and retain the fuel cap and hardware attaching the fender to the frame.
-
Page 4: Installing The Rollover Protection System (Rops)
Installing the Rollover Protection System (ROPS) Parts needed for this procedure: Upper roll bar assembly Left lower roll bar assembly Right lower roll bar assembly Fold-pin assembly Shoulder bolt Locknut (1/2 inch) Bumper g331074 Figure 1 Flange-head bolt (5/8 x 3-1/2 inches) 1. - Page 5 Secure the lower roll bar assemblies to the upper roll bar assembly using the 2 shoulder bolts, 2 wave washers, 2 locknuts (1/2 inch), and fold-pin assembly (Figure g331075 Figure 3 1. Upper roll bar assembly 4. Wave washer 2. Fold-pin assembly (fold 5.
-
Page 6: Operation
Lowering the Roll Bar Operation Important: Lower the roll bar only when absolutely necessary. Using the Remove the hairpin cotters and remove the 2 Rollover-Protection System pins (Figure (ROPS) Lower the roll bar to the down position (Figure Note: There are 2 down positions; refer to WARNING Figure To avoid injury or death from rollover, keep... -
Page 7: Maintenance
Raising the Roll Bar Maintenance Important: Always use the seat belt with the roll bar in the raised position. Checking the Seat Belt Remove the hairpin cotters and remove the 2 Service Interval: Before each use or daily pins (Figure Raise the roll bar to the upright position, install Inspect the seat belt for wear, cuts, and proper the 2 pins, and secure them with the hairpin...
Need help?
Do you have a question about the 144-1848 and is the answer not in the manual?
Questions and answers