Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Notes: software & drivers. • Figures can deviate due to the different set executions. Table 2-1 Described Model Numbers and Diversity Block Mechanics Diagrams Schematics 50PUT6800/56 & 10.1 10.3 10.4 10.5 10.7 11.1 55PUT6800/56 &...
Page 3
Technical Specs, Diversity, and Connections QM15.2A LA EN 3 Connections Rear Connectors Side Connectors AUDIO IN SERV .U NETWORK TV ANTENNA DIGITAL HDMI 1 HDMI 2 AUDIO OUT USB1 19930_001.eps Figure 2-1 Connection overview Note: The following connector colour abbreviations are used 3 - HDMI 4: Digital Video - In, Digital Audio with ARC/MHL - (acc.
Page 4
EN 4 QM15.2A LA Technical Specs, Diversity, and Connections - D2+ Data channel - +5V - Shield - Data (-) - D2- Data channel - Data (+) - D1+ Data channel - Ground - Shield - D1- Data channel 13 - HDMI 1: Digital Video - In, Digital Audio with ARC - - D0+ Data channel In/Out...
Spare Parts the following points: • Route the wire trees correctly and fix them with the For the latest spare part overview, consult your Philips Spare mounted cable clamps. Part web portal. • Check the insulation of the Mains/AC Power lead for external damage.
Page 6
EN 6 QM15.2A LA Precautions, Notes, and Abbreviation List result in sets which have the same CTN (Commercial Type 6 = play 16 : 9 format, 12 = play 4 : 3 Number; e.g. 28PW9515/12) but which have a different B.O.M. format number.
Page 7
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 8
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4-wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
Mechanical Instructions QM15.2A LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assembly/Panel Removal 4.4 Set Re-assembly Cable Dressing ECN700 CN8101...
Page 10
EN 10 QM15.2A LA Mechanical Instructions ECN4250 ECN700 CN8101 WIFI MODULE WiFi01 ECN4250 ECN402 ECN700 CN402 CN4250 MAIN POWER SUPPLY (1054) ECN408 (1053) ECN01 ECN402 ECN401 KEYBOARD CONTROL (1057) ECN408 ECN601 ECN401 LOUDSPEAKER LOUDSPEAKER (1184) (1184) IR/LED BOARD (1056) 19940_100.eps Figure 4-2 Cable dressing (55"...
Page 11
Mechanical Instructions QM15.2A LA EN 11 Service Positions For easy servicing of a TV set, the set should be put face down on a soft flat surface, foam buffers or other specific workshop tools. Ensure that a stable situation is created to perform measurements and alignments.
Page 12
EN 12 QM15.2A LA Mechanical Instructions 4.3.2 Rear Cover (for 65" 6800 series) fixation screws [2],[3],[4] that secure the rear cover & service_cover. Refer to Figure 4-6 for details. 2. Gently lift the service_cover from the TV. Then unplug the Refer to Figure 4-6 &...
Page 13
Mechanical Instructions QM15.2A LA EN 13 Q3 × 6 19940_103.eps Figure 4-8 Keyboard & Ambilight removal 4.3.4 Small Signal Board (SSB) Refer to Figure 4-9 for details. Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB.
Page 14
EN 14 QM15.2A LA Mechanical Instructions 4.3.6 Speakers 1. Gently release the tapes that secure the speaker cables. 2. Unplug the speaker connector from the SSB. 3. Take the speakers out. When defective, replace the both units. 4.3.7 Stand bracket 1.
Service Modes and Fault Finding QM15.2A LA EN 15 5. Service Modes and Fault Finding Index of this chapter: SAM in a decimal value. Every two soft-resets increase the 5.1 Test Points hour by + 1. Stand-by hours are not counted. 5.2 Service Modes 5.3 Stepwise Start-up Software Identification, Version, and Cluster...
Page 16
EN 16 QM15.2A LA Service Modes and Fault Finding Table 5-1 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Description Hardware info The information of Hardware. Operation hours This represents the life timer. The timer counts normal operation hours, but does not count Stand-by hours.
Page 17
Service Modes and Fault Finding QM15.2A LA EN 17 Table 5-2 Factory mode overview Default value Item Item value 50" & 55" 6800 65" 6800 Description F/W VERSION Press OK Displays the software versions of the supplier, Flash PQ, Smart Picture, BL Dimming, Source Meter, the Picture Quality checksum, the Dimming library, the Source meter library, the Flash AQ, MCU and OAD software versions.
Page 18
EN 18 QM15.2A LA Service Modes and Fault Finding How to Exit the Factory mode • 2.4 Strings database version Displays the version of Use one of the following methods: strings database. • Select EXIT_FACTORY from the menu and press the “OK” •...
Page 19
A description on how to upgrade the main check that what the current TV software: software can be found in the DFU or on the Philips website. 1. Press the “Home screen” + “1999” + “Back” button on the remote control to enter the Factory mode.
Page 20
EN 20 QM15.2A LA Service Modes and Fault Finding 5.4.5 Update the TV software • FUS_clustername_version.zip: Contains the “autorun.bin” which is needed to upgrade the TV main software and the software download application. 1. Turn the TV on and wait for it to boot completely. •...
1 mV and a frequency of Picture mode Screen size Green Blue 61.25 MHz (channel 3). Normal (9000K) 50PUT6800/56 • LATAM models: an NTSC M TV-signal with a signal 55PUT6800/56 strength of at least 1 mV and a frequency of 55PUT6800/79 61.25 MHz (channel 3).
Page 22
Blue the TV has to be set according to the type plate of the set. For Cool (11000K) 50PUT6800/56 this, you can use the NVM editor in SAM. The loading of the 55PUT6800/56 CTN and production code can also be done via ComPair 55PUT6800/79 (Model number programming).
Circuit Descriptions QM15.2A LA EN 23 7. Circuit Descriptions Index of this chapter: Introduction 7.1 Introduction The QM15.2A LA is a new chassis launched in AP in 2015. The 7.2 Power Supply whole range is covered by MT5593UPIJ. The major deltas 7.3 DC/DC Converters versus its predecessor support PAL/NTSC/SECAM, with 7.4 Front-End Analogue and DVB-C, DVB-T2 reception...
Page 24
EN 24 QM15.2A LA Circuit Descriptions 7.1.3 SSB Cell Layout DC/DC MT5593FPIJ/UPIJ DC/DC ANALOG I/O HDMI HDMI DC/DC Tuner NETWORK SPDIF HDMI HDMI Headphone 19940_200.eps Figure 7-1 SSB layout cells (top view) (6800 series) back to 2016-Jan-15 div.table...
Page 25
Figure 7-3 Power Architecture (65" 6800 series) 7.2.1 Power Supply Unit Consult the Philips Service web portal for the order codes of the boards. All power supplies are a black box for Service. When defective, a new board must be ordered and defective one must be Important delta’s with the QM15.2A LA classis platform are:...
Page 26
EN 26 QM15.2A LA Circuit Descriptions The control signals are: 7.2.3 Connector overview • Stand-by • Lamp “on/off” Table 7-1 Connector overview • DIM (PWM) (not for PSDL) Connector In this manual, no detailed information is available because of 50" & 55" design protection issues.
Page 27
Circuit Descriptions QM15.2A LA EN 27 Figures gives a graphical representation of the DC/DC converters with its current consumptions: +12V_AU U601 TAS5760 STB_PWR(3.7V) 3V3SB D705 DC/DC U4251 WI-FI Vcc 3.3V/1.2A AP7362 Vcck 1.0V DC/DC U704 +12V MT5593 RT7299B PGOOD DC/DC U708 +5V_SW SY8368 U102...
Page 28
EN 28 QM15.2A LA Circuit Descriptions Front-End Analogue and DVB-C, DVB-T2 HDMI reception Refer to figures 7-7 HDMI input configuration. 7.4.1 Front-End Analogue and DVB-C Part The Front-End for the analogue tuner consist of the following key components: MT5593 • SCALER MT5593UPIJ HSBGA-900 •...
IC Data Sheets QM15.2A LA EN 29 8. IC Data Sheets This chapter shows the internal block diagrams and pin configurations of ICs that are drawn as “black boxes” in the electrical diagrams (with the exception of “memory” and “logic” ICs).
Page 30
EN 30 QM15.2A LA IC Data Sheets Pinning Information MT5593FPIJ/UPIJ DEMO HDMI_ HDMI_ HDMI_ HDMI_ HDMI_ HDMI_ HDMI_ HDMI_ AVDD AVDD AVDD CI_A1 CI_MD CI_MD SPI_D CI_TS SSUSB AIN_R AIN_R USB_D USB_D SSUSB SSUSB 0_RX_ 0_RX_ 0_RX_ 0_RX_ 1_RX_ 1_RX_ 2_RX_ 3_RX_ 10_HD...
Page 31
IC Data Sheets QM15.2A LA EN 31 Diagram 10-3-8 Speaker/Headphone B08, TAS5760LDDCAR (IC U601) Block diagram PVDD GVDD_REG TAS5760LD Internal Internal Reference Internal Gate DRVDD Voltage Regulators Drive Regulator Supplies Closed Loop Class D Amplifier SFT_CLIP Full Bridge Digital to SPK_OUTA+ Digital Power Stage...
Page 32
EN 32 QM15.2A LA IC Data Sheets Personal Notes: 10000_012_090121.eps 110804 back to 2016-Jan-15 div.table...
Circuit Diagrams and PWB Layouts QM15.2A LA EN 46 10.3 B 715G7030 SSB 10-3-1 System Power 1 System Power 1 DC POWER INPUT BRIGHT_ADJ: INVERTER_ON_OFF: OPWRSB: Normal:Max:+3V3, Min:0V Normal: High Normal: Low Stand_By:0V Stand_By: Low Stand_by: High OPWRSB 5,7,16 OPWRSB STB_PWR 3V3SB +12V_AU...
Page 47
Circuit Diagrams and PWB Layouts QM15.2A LA EN 47 10-3-2 System Power 2 System Power 2 Audio VCC= +12V 5,7,8,9,10,11,12,13,14,15,16,17,18,19 Panel VCC=12V or 5V FB754 PVDD +12V_AU PANEL_VCC_ON/OFF 120R PANEL_VCC_ON/OFF PVDD PVDD PANEL_VCC +5V_SW +12V LNB_EN LNB_EN LNB_LINEDROP PANEL VCC FB750 FB751 R751...
Page 48
Circuit Diagrams and PWB Layouts QM15.2A LA EN 48 10-3-3 Peripheral Peripheral U401-7 AE36 U0TX DVDD3V3 U0TX AE37 5,6,8,9,10,11,12,13,14,15,16,17,18,19 U0RX CPC0 U0RX R4003 CPC1 4K7 1/16W 5% AM38 U1TX OPWRSB DVDD3V3 CPC2 U1TX 5,16 OPWRSB AM37 U1RX U1RX SY S_EEPROM_WP R4004 SY S_EEPROM_WP AT37...
Page 57
Circuit Diagrams and PWB Layouts QM15.2A LA EN 57 10-3-12 Connector Connector OSCL1 7,12,13,15 OSCL1 OSDA1 7,12,13,15 OSDA1 LED_PWM0 7,17 LED_PWM0 3V3SB LED_PWM1 7,17 LED_PWM1 TO KEY PAD BOARD L/R_IN HTV IR IN/OUT 13,17 L/R_IN Gaming Gaming L/R_OUT 13,17 L/R_OUT R4100 6K8 1% 3V3SB...
Page 58
Circuit Diagrams and PWB Layouts QM15.2A LA EN 58 10-3-13 Internal CI Internal CI HP_DET HP_DET MHL_PWR_EN U401-8 MHL_PWR_EN CI_A0 DEMOD_RST CI 3V3 PWR Cap. GPIO0 CI_A0 DEMOD_RST CI_A1 DEMOD_TSCLK SY S_EEPROM_WP CI Slot GPIO1 CI_A1 DEMOD_TSCLK SY S_EEPROM_WP CI_A2 DEMOD_TSDATA0 PANEL_VCC_ON/OFF GPIO2...
Circuit Diagrams and PWB Layouts QM15.2A LA EN 63 10.4 J 715G7074 IR/LED Panel 10-4-1 IR & 3D & Light sensor & LOGO IR & 3D & Light sensor & LOGO Standby Lighting LOGO IR Receiver 3V3SB 3V3SB CN201 3V3SB 3V3SB LED_R 3V3SB...
Circuit Diagrams and PWB Layouts QM15.2A LA EN 65 10.5 E 715G7118 Keyboard control panel 10-5-1 CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Center 2-5 short Menu CN01 Right 1-5 short 0.5V KEY 1 AMBI_SPI_CLK Left 4-5 short 0.81V AMBI_SPI_MOSI 0.1uF 50V...
Page 66
Circuit Diagrams and PWB Layouts QM15.2A LA EN 66 10-5-2 Key board layout Layout Keyboard control panel (top side) Layout Keyboard control panel (bottom side) SW01 SW11 2014-11-06 Keyboard control panel 715G7118 layout top/bottom 19792_511.eps back to 2016-Jan-15 div.table...
Circuit Diagrams and PWB Layouts QM15.2A LA EN 76 10.9 AL 715G7007 Ambilight 10-9-1 TCL5971 TLC5971 AL01 AL01 +12V +12V TPVision used part only, not TPV AVL XA02 XA05 CONN NC/CONN Reference Description Part ID U001 LMV321IDCKR 356G0192005600 +3V3 C003 100N16V D100 Shottky BAT54WS...
Need help?
Do you have a question about the 50PUT6800/56 and is the answer not in the manual?
Questions and answers