Advertisement
Available languages
Available languages
Quick Links
The Deck Grommet™ Pro accommodates a minimum deck ooring thickness of 7/8" to a maximum of 1-5/8" and a
minimum width of 5-1/4". The deck ooring must be a minimum of 2 feet above ground surface.
WARNING
• For outdoor use only.
• Use this product only for its intended use as
described in this installation instruction.
• DO NOT install in line with a power converter.
• DO NOT use attachments not recommended by
manufacturer.
• DO NOT insert foreign objects into power outlet
receptacles.
• DO NOT attempt to repair if any malfunction
occurs.
• Used for mounting on deck board materials only.
• This product (as supplied) has no eld serviceable parts.
Deck Grommet™ Pro Includes:
(Parts List)
A. (1) Deck Grommet
B. (1) Cut-Out Template
C. (1) Device Cover Plate
D. (1) Duplex Receptacle Adapter
E. (2) Flexible Cord Connector
F. (1) 3 Wire Flexible Cord
Type SJOOW (3 feet, one end
stripped, one end unstripped)
B
C
D
Required Items
(Not Included)
Weatherproof outlet box and cover
(Red•Dot Cat. Nos. IH3-1 (Box) & CCB (Cover) recommended)
GFCI or Standard Duplex Receptacle - Weather
Resistant (WR) and Tamper Resistant (TR)
TA04771-1 A Page 1 of 4
INSTALLATION INSTRUCTIONS
for The Deck Grommet™ Pro
Catalog Number DKG-PRO
A
E
F
RISK OF SHOCK, DISCONNECT
POWER BEFORE INSTALLATION.
CAUTION
The Deck Grommet™ Pro shall be installed by a
quali ed electrician in accordance with the National
and Local Electrical Codes.
INSTALLATION INSTRUCTIONS:
1. Cut-out Instructions
1.1 Select the deck location where the Deck
Grommet™ Pro will be installed.
1.2 IMPORTANT: Be sure that there are no obstructions
under the deck ooring before any cut-out is made.
Deck ooring must be a minimum of 2 feet above
ground surface (see Figure 1).
1.3 Position the Cut-Out Template (B) (supplied)
centrally between the width (5-1/4" min.) of one of
the deck boards and a minimum of 2" away from
the joist (see Figure 1).
1.4 When positioned, trace the cut-out shape onto
the deck board (see Figure 2).
1.5 Drill 1/2" diameter starter hole along the inside
edge of the traced cut-out and use a jig saw to
cut the outlined shape through the deck surface.
Cut-Out Template
centrally between
Deck Boards
Joist
(both sides)
Shows three different ways to
FIGURE 1
position the cut-out template.
Trace around Cut-Out
Template
FIGURE 2
WARNING
English
2' min. from ground
2" minimum
away from joist
(Typical - both sides)
Advertisement
Related Manuals for ABB Thomas&Betts Reddot The Deck Grommet Pro
Summary of Contents for ABB Thomas&Betts Reddot The Deck Grommet Pro
- Page 1 WARNING RISK OF SHOCK, DISCONNECT POWER BEFORE INSTALLATION. INSTALLATION INSTRUCTIONS English for The Deck Grommet™ Pro Catalog Number DKG-PRO The Deck Grommet™ Pro accommodates a minimum deck ooring thickness of 7/8” to a maximum of 1-5/8” and a minimum width of 5-1/4”. The deck ooring must be a minimum of 2 feet above ground surface. WARNING CAUTION •...
- Page 2 2. Electrical Wiring and Mounting Procedure 2.3 Connect the supplied Flexible Cord (E) to the Deck Grommet™ Pro (A) using the supplied 2.1 Select an approved tamper resistant and weather Flexible Cord Connectors (E) (see Figure 5 & 6). resistant type receptacle (15A or 20A) to be installed.
- Page 3 Wiring Chamber Duplex Receptacle Installed Tighten Swing Clamp Screws (4) Duplex Adapter (D) (4) Swing Clamps (Both Sides) Device Cover (C) FIGURE 8 CAUTION FIGURE 10 When a nonGFCI protected receptacle is used, the branch circuit servicing the receptacle shall be GFCI protected. 3.
- Page 4 NOTES: Flip Open Cover Insert Plug Create Drip Loop FIGURE 12 Cord Exit Slots Electrical Cord FIGURE 13 WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product for the user's intended application.
-
Page 5: Instrucciones De Instalación
ADVERTENCIA RIESGO DE DESCARGA, DESCONECTE LA ENERGÍA ANTES DE LA INSTALCIÓN INSTRUCCIONES DE INSTALACIÓN Español para el Deck Grommet™ Pro Número de catálogo DKG-PRO El Deck Grommet™ Pro se adapta a un piso de plataforma con espesor mínimo de 7/8" hasta un máximo de 1-5/8" y una anchura mínima de 5-1/4". - Page 6 2. Cableado eléctrico y procedimiento de montaje 2.3 Conecte el cable exible suministrado (E) al Deck Grommet™ Pro (A) utilizando los conectores del 2.1 Seleccione un tomacorrientes apropiado de tipo cable exible suministrados (E) (véase la Figura 5 y 6). resistente a la manipulación y a la intemperie (15A o 20A) para ser instalado.
- Page 7 Cámara de cableado Tomacorrientes Apriete dúplex instalado los tornillos de los sujetadores pivotantes (4) Adaptador Dúplex (D) (4) Sujetadores pivotantes (ambos lados) Cubierta del dispositivo (C) FIGURA 8 PRECAUCIÓN FIGURA 10 Cuando se utilice un tomacorrientes no protegido según GFCI, el circuito derivado que alimenta al tomacorrientes deberá...
- Page 8 NOTAS: Abra la cubierta Inserte el enchufe Forme un lazo de goteo FIGURA 12 Ranuras para salida de cables Cable eléctrico FIGURA 13 GARANTÍA: Thomas & Betts vende este producto en el entendimiento de que el usuario realizará todas las pruebas necesarias para determinar la idoneidad de este producto para la aplicación prevista del usuario.
Need help?
Do you have a question about the Thomas&Betts Reddot The Deck Grommet Pro and is the answer not in the manual?
Questions and answers