Advertisement
Quick Links
This Addendum contains updated information for the following Efficia CMS200 documentation:
•
Service Guide
•
Installation and Configuration Guide
Please store this Addendum with your Efficia documentation for future reference.
Change made to Overview, Chapter 1, Service Guide
The description of "Display or dual displays" has been changed to the following:
Component
Display or dual displays
Change made to Display Problems, Chapter 4, Service Guide
The "Display Problems" section has been changed to the following:
Symptom
The Efficia CMS200
display is blank.
Efficia CMS200 Documentation Addendum
Efficia CMS200 Central Monitoring System
Documentation Addendum
for Software Release 2.3
Description
Allow viewing of the patient data and alarms from the connected monitors.
Each display is connected to the PC in one of the following ways:
• Connecting the display to the PC at the DisplayPort interface with a
DisplayPort cable.
• Connecting the display to the PC at the VGA port with a VGA cable.
• Connecting the display to the PC at the HDMI port with an HDMI cable.
Probable Cause
The display is not connected to
AC power or is not powered on.
The signal cable (the DisplayPort
cable, VGA cable or HDMI cable)
is disconnected or connected
incorrectly.
The cables are faulty.
The display is faulty.
Solution
Verify that the display power cord is
connected to a power source and that the
display is powered on.
Verify that the signal cable (the DisplayPort
cable, VGA cable or HDMI cable) is inserted
completely into the connector on the PC.
Replace the cables.
Replace the display.
Page 1-7
Advertisement
Related Manuals for Philips Efficia CMS200
Summary of Contents for Philips Efficia CMS200
- Page 1 Efficia CMS200 Central Monitoring System Documentation Addendum for Software Release 2.3 This Addendum contains updated information for the following Efficia CMS200 documentation: • Service Guide • Installation and Configuration Guide Please store this Addendum with your Efficia documentation for future reference.
- Page 2 See the “Adjusting the Display” section in the Service Guide. The display is faulty. Replace the display. The Efficia CMS200 is The display is not connected to Verify that the display power cord is configured for dual AC power or is not powered on.
- Page 3 Change made to Unpacking and Inspecting Components, Chapter 3, Installation and Configuration Guide If you have purchased one or two medical displays, after you unpack the Efficia CMS200 components, verify that each display includes: • A VGA cable.
- Page 4 PC Connectors, Ports, and LEDs The hardware for the Efficia CMS200 includes the HP Engage Flex series PC. The following illustrations and table describe the connectors and LEDs on the front and back of the PC that are used with the Efficia CMS200 components.
- Page 5 HL7 interface server. Audio-out (headphone)/Audio-in (microphone) combo jack. Use to connect the display/speaker. Connecting the Philips Medical Displays to the PC The following procedure uses the example of connecting the primary display to the PC at the VGA port. Cables Required •...
- Page 6 To connect the Philips medical displays to the PC: Step Make sure the displays are in a convenient, well-ventilated location near the PC. Note — If you are connecting two displays, position the secondary display to the right of the primary display.
- Page 7 Do not use a signal cable converter. Input Power 100-240 VAC, 50/60Hz Philips Medizin Systeme Böblingen GmbH Hewlett-Packard Strasse 2 71034 Böblingen, Germany ©Copyright 2023 Koninklijke Philips N.V. All rights are reserved. Printed in China 453665095801 Revision A *453665095801* 0123 Efficia CMS200 Documentation Addendum Page 7-7...
Need help?
Do you have a question about the Efficia CMS200 and is the answer not in the manual?
Questions and answers