Advertisement
Quick Links
Advertisement
Related Manuals for Haier HMO60S11EB1
Summary of Contents for Haier HMO60S11EB1
- Page 1 Microwave Oven HMO60S11EB1 INSTALLATION GUIDE NZ AU...
- Page 3 CONTENTS Safety and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Prior to installation .
- Page 4 SAFETY AND WARNINGS WARNING! Electrical Shock Hazard Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricity supply. Connection to a good ground wiring system must only be made by a qualified electrician. Failure to follow this advice may result in electrical shock or death.
- Page 5 SAFETY AND WARNINGS READ AND SAVE THIS GUIDE IMPORTANT SAFETY INSTRUCTIONS! To reduce the risk of fire, electrical shock, injury to persons or damage when using the oven, follow the important safety instructions listed below. Read all the instructions before using the oven. Use the oven only for its intended purpose as described in these instructions.
- Page 6 SAFETY AND WARNINGS Food and liquids Leave food in the oven for as short a time as possible before and after cooking. This is to avoid contamination by organisms which may cause food poisoning. Take particular care during warm weather. Eggs in their shells and whole hard-boiled eggs should not be heated in microwave ovens since they may explode, even after microwave heating has ended.
- Page 7 If the microwave oven is installed as a built-in, observe the following instructions: Do not mount over a sink. Do not store anything directly on top of the appliance surface when the appliance is in operation. If the microwave oven light fails, consult a Haier authorised servicer.
- Page 8 SAFETY AND WARNINGS Cleaning The oven must be cleaned regularly and all food residues must be removed. Failure to keep the oven clean could cause deterioration of the surfaces that could reduce the life of the appliance and cause dangerous conditions. Do not clean the oven seal or use any oven-cleaning products on it.
- Page 9 PRIOR TO INSTALLATION Ensure that: The material of the unit supporting the appliance is heat resistant or covered with a heat resistant material . The cavity ventilation has been set up correctly . The countertop and oven cavity are square and level, and are the required dimensions . The installation will comply with all clearance requirements and applicable standards and regulations .
- Page 10 COMPONENTS REQUIRED TOOLS Not supplied Box cutter Phillips screwdriver PARTS Supplied and required 4x M4 .2x25 screws *Not required for single product installation.
- Page 11 PRODUCT DIMENSIONS FRONT SIDE Overall height Overall width Overall depth Height of chassis Width of chassis Depth of chassis Depth of oven frame and control panel (distance between front of chassis and front of oven door) Depth of oven door when fully open (measured from front of control panel)
- Page 12 CABINETRY DIMENSIONS SIDE PROUD INSTALL 16–20mm 20mm Electrical supply FLUSH INSTALL 16–20mm 20mm Overall height of cabinetry Minimum inside height of cavity Overall width of cabinetry Minimum inside width of cabinetry Minimum inside depth of cabinetry Ventilation air vent Note: If installing a cooktop above the oven, ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer's instructions.
- Page 13 ELECTRICAL CONSIDERATIONS WARNING! All electrical work must be carried out by a suitably qualified and authorised electrician. No alterations or wilful changes in the electricity supply should be carried out. The mains lead should be a minimum of 1 .5 metres long . Do not use an extension cord to connect your oven to the mains electricity supply .
- Page 14 CHECK CAVITY 1. Measure cavity dimensions . Ensure all minimum specifications have been met . 2. For dark cabinetry, ensure clashing has been considered and installed . 3. Ensure service access complies with local requirements . 4. Ensure cavity ventilation has been set up correctly .
- Page 15 Inspect the product to ensure there is no shipping damage . If any damage is detected contact the dealer or retailer you brought the product from to report the damage . Haier is not responsible for shipping damage . 1. Remove the carton sleeve and any transit packaging .
- Page 16 REMOVE SHELVES AND ACCESSORIES 1. Open the door and remove all packaging holding the racks, side racks and airfry tray in place . 2. Grip the racks at the front . Lift upwards and pull out from the microwave .
- Page 17 FIT AND SECURE OVEN INTO CAVITY 1. Connect the cable to the microwave . 2. Lift product into cavity . 3. Centre the oven in the cavity ensuring there is at least 10mm between the oven and surrounding cabinetry . 4.
- Page 18 FIT TURNTABLE AND RACKS 1. Position the turntable wheel guides correctly on the mechanism so that the rollers are at the top . 2. Place the glass turntable plate correctly onto the wheel guides . 3. Refit side racks, main racks and air fry tray .
- Page 19 INSTALLER CHECKLIST To be completed by the installer Check all parts are installed correctly and are secure . Ensure all packaging, tape and rubberbands have been removed . Ensure all clearance gaps have been maintained . Ensure all electrical tests have been conducted in accordance with local regulations . Complete and keep for safe reference: Model Serial no .
- Page 20 WWW .HAIER .COM .AU 条形码尺寸40*8mm， 由厂家生成。 WWW .HAIER .CO .NZ 432404A 9415112619032 07.24...
Need help?
Do you have a question about the HMO60S11EB1 and is the answer not in the manual?
Questions and answers