1060 DIMM (in bottom slot) . . 92 Diagnostics using PC-Doctor for DOS . 45 1070 PCI Express Mini Card for wireless WAN . 93 Lenovo ThinkVantage Toolbox (Lenovo System 1080 Keyboard . . 95 Toolbox) . 48 1090 DIMM (in slot under keyboard) .
Page 6
Locations ... . . 149 Recovery discs . . 183 Windows XP Professional (32 bit) DVDs . . 183 Front view . . 149 Windows Vista Business (32 bit) DVDs . .
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges.
Page 12
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: –...
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information...
Page 16
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Page 17
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the...
Page 20
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas.
Page 21
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
Page 22
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit.
Page 23
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
Page 24
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
Page 25
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht werden.
Page 32
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían.
Page 33
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive.
Page 38
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Page 39
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options. Si l’une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à...
Page 40
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1. Bei der Installation von CD-ROM-Laufwerken, DVD-ROM-Laufwerken oder anderen Lasereinheiten Folgendes beachten: VORSICHT:...
Page 44
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
– “FRU identification for CTO, CMV, and GAV products” on page 41 Important: BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.lenovo.com/support System Disassembly/Reassembly videos that show the FRU removals or ®...
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
MT and 3-digit model, where model = “CTO” (Example: 1829-CTO). Custom Model Variant (CMV) This is a unique configuration that has been negotiated between IBM or Lenovo and the customer. A unique 4-digit MT and 3-digit model is provided to the customer to place orders (Example: 1829-W15).
Page 50
(this is the same record found in PEW). v eSupport can be accessed at the following Web site: http://www.lenovo.com/ support v To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP.
“Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 48 – “PC-Doctor for Rescue and Recovery” on page 48 – “FRU tests” on page 49 v “Power system checkout”...
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3.
If you test one of these devices, you will need to enable it by using Configuration utility for DOS. The utility is available on the following Web site: http://www.lenovo.com/support PC-Doctor cannot be used to test a device that is in the docking station, even if the computer supports the docking station.
Testing the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. To run the test, do as follows: 1. Turn off the computer. 2.
Page 55
The options on the test menu are as follows: Diagnostics Interactive Tests v Run Normal Test v Keyboard v Run Quick Test v Video v CPU/Coprocessor v Internal Speaker v System board v Mouse v Video Adapter v Diskette v Fixed Disks v System Load v Diskette Drives v Optical Drive Test...
While the Windows operating system is running, press the ThinkVantage button. You can also run this program as either of the following: v Click Start --> All Programs --> Lenovo ThinkVantage Tools --> System Health and Diagnostics. v Click Start --> Control Panel --> System and Security --> Lenovo’s System Health and Diagnostics.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad Notebook, detach it. 4.
Page 58
Table 1. FRU tests (continued) Applicable test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Advanced Memory Tests. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. TrackPoint or If the TrackPoint does not work, check the configuration as pointing device...
Power system checkout To verify a symptom, do the following: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 85). 4. Remove the backup battery (see “1100 Backup battery” on page 103). 5.
Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/spm Restoring the factory contents by using Recovery Disc Set When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery program is on the new drive.
Note: Recovery takes several hours. The length of time depends on the method you use. If you use recovery discs, recovery takes at least five hours. 1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure: a.
If it has, it can be used for access to the hard disk drive. If no master HDP is available, neither Lenovo nor Lenovo authorized service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive.
Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the service technician, neither Lenovo nor Lenovo authorized service technicians provide any services to reset the user HDPs or to recover data from the hard disk drive.
Page 67
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed. Related service information...
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v “LCD-related symptoms” on page 68 v “Intermittent problems” on page 69 v “Undetermined problems”...
Page 71
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 System board. EAIA data access error—The access to EEPROM is failed. 0188 System board. Invalid RFID Serialization Information Area. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct.
Page 72
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0251 1. Charge the backup battery for more System CMOS checksum bad— Default than 8 hours by connecting the ac configuration used. adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
Page 73
Warning: Your internal hard disk drive customer: If in the primary bay the customer (HDD) may not function correctly on this is using a non-IBM or non-Lenovo hard disk system. Ensure that your HDD is supported drive (HDD), or an old generation IBM...
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or 1. Reseat the LCD connector. flashing LCD. 2. LCD assembly. 3. External CRT. 4. System board. One long and two short beeps, and a blank 1.
If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty. However, if the LCD has three or more visible defective pixels, it will be deemed as defective by Lenovo and it should be replaced. Notes: v This policy applies to all ThinkPad Notebooks purchased on 1 January, 2008 or later.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.
Page 80
Table 7. Status indicators Indicator Meaning Speaker mute Orange: The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. Microphone Orange: mute The microphone is on mute. None of the recording devices is available while the microphone mute is on by default.
Page 81
Table 7. Status indicators (continued) Indicator Meaning Numeric lock By default, when the numeric lock is on, the numeric lock (On-screen indicator is displayed on the screen. indicator) Serial Ultrabay Green: A Serial Ultrabay Slim device is installed and in use. Slim device Blinking green: status...
Page 84
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings.
Page 85
Table 8. Fn key combinations (continued) Key combination Description Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds. Notes: To use this combination of the keys, ThinkPad PM device driver must have been installed on the computer.
Before replacing the system board, save the original serial number by doing the following: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 1. Set System Identification.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID.
Before servicing ThinkPad T410 and T410i Some models of the ThinkPad T410 and T410i you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing.
The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. If ThinkVantage Toolbox or Lenovo System Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced.
Page 94
Table 9. Removal steps of battery pack (continued) Unlock the battery latch 1 . Holding the battery latch in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . When installing: Install the battery pack in the slot, and then make sure that the battery latch is in the locked position.
1020 ExpressCard blank bezel Table 10. Removal steps of ExpressCard blank bezel When you press the ExpressCard blank bezel 1 , it pops out 2 . When installing: Make sure that the bezel is correctly oriented as shown in this figure.
1030 Serial Ultrabay Slim device or travel bezel For access, remove this FRU: v “1010 Battery pack” on page 85 Table 11. Removal steps of Serial Ultrabay Slim device or travel bezel Holding the bay lock latch in the unlocked position 1 , slide the bay eject latch 2 , and then pull out the Ultrabay Slim Media Bay device or the travel bezel in the direction shown by arrow 3 .
1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD) For access, remove this FRU: v “1010 Battery pack” on page 85 Attention: v Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock.
Page 98
Table 12. Removal steps of HDD slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD) (continued) For HDD and HDD rubber rails: For SSD and storage converter: When installing: Make sure that the SSD connector or HDD connector is attached firmly.
1050 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 85 Table 13. Removal steps of DIMM slot cover Note: Loosen the screw 1 , but do not remove it. Removing and replacing a FRU...
1060 DIMM (in bottom slot) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 Note: This product has two DIMM slots: one under the keyboard and another on the underside of the computer.
1070 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 Table 15. Removal steps of PCI Express Mini Card for wireless WAN In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Page 102
Table 15. Removal steps of PCI Express Mini Card for wireless WAN (continued) Note: Plug the red cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card. If the computer you are servicing is a wireless WAN-ready model and does not have the wireless WAN card, route the antenna cables and secure them with a tape as shown in this figure.
1080 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 Table 16. Removal steps of keyboard Step Screw (quantity) Color Torque M2 × 10 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm)
Page 104
Table 16. Removal steps of keyboard (continued) Push down the keyboard a little toward the arrow 2 to detach the front edge of the keyboard from the frame. ThinkPad T410 Hardware Maintenance Manual...
Page 105
Table 16. Removal steps of keyboard (continued) Lift the keyboard a little in the direction shown by arrow 3 , and then detach the connector 4 . Removing and replacing a FRU...
Page 106
When installing the keyboard, do as follows: Table 17. Installation steps of keyboard 1. Attach the keyboard connector. ThinkPad T410 Hardware Maintenance Manual...
Page 107
Table 17. Installation steps of keyboard (continued) 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure. 3. To make sure that the front edge of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you.
Page 108
Table 17. Installation steps of keyboard (continued) 4. Make sure that front edge of the keyboard b is attached firmly. 5. Secure the keyboard by tightening the screws from the bottom side of the computer. ThinkPad T410 Hardware Maintenance Manual...
1090 DIMM (in slot under keyboard) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 Note: This product has two DIMM slots: one under the keyboard and another on the underside of the computer.
Page 110
Table 18. Removal steps of DIMM (in slot under keyboard) (continued) When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1100 Backup battery For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 Table 19. Removal steps of backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode.
Page 112
Table 19. Removal steps of backup battery (continued) Cable routing: Attach the backup battery and route the cable as shown in the figure below and make sure that the battery connector is attached firmly. ThinkPad T410 Hardware Maintenance Manual...
1110 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 Table 20. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Page 114
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack marked MAIN or M, and the black cable into the jack marked AUX or A on the card.
1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard”...
Page 116
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) ThinkPad T410 Hardware Maintenance Manual...
Page 117
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) When installing: Make sure that the connector is attached firmly. Removing and replacing a FRU...
Page 118
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) When installing: Make sure that the connectors are attached firmly. Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) ThinkPad T410 Hardware Maintenance Manual...
Page 119
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) When installing: Make sure that the connector is attached firmly. Removing and replacing a FRU...
1130 SmartCard or Contactless SmartCard For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 v “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)”...
Page 121
Table 22. Removal steps of SmartCard or Contactless SmartCard (continued) When installing: Make sure that the connector is attached firmly. Table 23. Removal steps of SmartCard dummy spacer Some models have SmartCard dummy spacer as a miscellaneous part. For those models, remove the spacer as follows: Step Screw (quantity)
1140 Modem daughter card (MDC) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 v “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)”...
1150 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1050 DIMM slot cover” on page 91 v “1080 Keyboard” on page 95 v “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)”...
Page 124
Table 25. Removal steps of speaker assembly (continued) Cable routing: Attach the speaker assembly and route the cable as shown in this figure, and make sure that the speaker connector is attached firmly. ThinkPad T410 Hardware Maintenance Manual...
1160 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
Table 26. Removal steps of LCD unit (continued) Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) ThinkPad T410 Hardware Maintenance Manual...
Page 127
Table 26. Removal steps of LCD unit (continued) Step Screw (quantity) Color Torque M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.0 kgfcm) Removing and replacing a FRU...
Page 128
Table 26. Removal steps of LCD unit (continued) When installing: v Make sure that you attach the connectors and route the cables firmly, and tape up in the proper positions as shown in this figure. v When you route the cables, make sure that they are not subjected to any tension.
Page 129
Table 26. Removal steps of LCD unit (continued) Removing and replacing a FRU...
Page 130
Table 26. Removal steps of LCD unit (continued) ThinkPad T410 Hardware Maintenance Manual...
1170 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
Page 132
Table 27. Removal steps of fan assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked a as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
Page 133
Table 27. Removal steps of fan assembly (continued) For Integrated graphics models: v When attaching the fan assembly to the frame, take care not to damage the heat sink ( a ) of the fan assembly. v Make sure that the fan connector is attached firmly. Removing and replacing a FRU...
1180 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
1190 Base cover assembly, I/O sub card, and I/O sub card cable For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1030 Serial Ultrabay Slim device or travel bezel” on page 88 v “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)”...
Page 136
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. ThinkPad T410 Hardware Maintenance Manual...
Page 137
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) When installing: Make sure that wireless switch is adjusted as shown in figure Removing and replacing a FRU...
Page 138
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) ThinkPad T410 Hardware Maintenance Manual...
Page 139
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) Cable routing: Make sure that connectors are firmly attached and route the cables as shown in this figure. Removing and replacing a FRU...
Page 140
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: Homologation label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1200 Magnesium structure frame For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1030 Serial Ultrabay Slim device or travel bezel” on page 88 v “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)”...
1210 System board, DC-in connector cable, and ExpressCard slot assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1030 Serial Ultrabay Slim device or travel bezel” on page 88 v “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)”...
Page 144
Table 31. Removal steps of system board, DC-in connector cable, and ExpressCard slot assembly Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. ™...
Page 145
Table 31. Removal steps of system board, DC-in connector cable, and ExpressCard slot assembly (continued) Step Screw (quantity) Color Torque M2 × 10 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
2010 LCD bezel assembly For access, remove the following FRU: v “1010 Battery pack” on page 85 Table 32. Removal steps of LCD bezel assembly Step Screw cap Screw (quantity) Color Torque M2.5 × 6 mm, wafer-head, Black 0.392 Nm nylon-coated (4) (4.0 kgfcm) ThinkPad T410 Hardware Maintenance Manual...
Page 147
Table 32. Removal steps of LCD bezel assembly (continued) Removing and replacing a FRU...
2020 LED board For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 138 Table 33. Removal steps of LED board Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm)
2030 Integrated camera For access, remove these FRUs, in order: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 138 Table 34. Removal steps of integrated camera Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm)
2040 LCD panel and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
Page 151
Table 35. Removal steps of LCD panel and LCD cable (continued) Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) When installing: When attaching the LCD panel to the cover, press the left and right edges covered with metal gently with your fingers.
2050 Camera cable For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
Page 153
Table 36. Removal steps of camera cable (continued) Cable routing: When you install the cable, route the cable as shown in the figure below. Removing and replacing a FRU...
2060 Wireless LAN antenna assembly or wireless LAN/WAN antenna assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN”...
Page 155
Table 37. Removal steps of wireless LAN antenna assembly or wireless LAN/WAN antenna assembly (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) Removing and replacing a FRU...
2070 Hinges and LCD rear cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 ExpressCard blank bezel” on page 87 v “1050 DIMM slot cover” on page 91 v “1070 PCI Express Mini Card for wireless WAN” on page 93 v “1080 Keyboard”...
Rear view Status indicators Note: For the description of each indicator, see “Status indicators” on page DisplayPort HDD or SSD Universal serial bus (USB) connectors RJ-45 (Ethernet) connector External monitor connector AC power connector RJ-11 (modem) connector Locations...
Page 163
Table 39. Parts list—Overall FRU (Overall) FRU no. a - g See “Miscellaneous parts” on page 179. LCD unit (see “LCD FRUs” on page 170.) Keyboard bezel assembly without fingerprint reader 60Y4955 v 2516-CTO, A6x, ADx, AEx v 2518-CTO, CHx, EMx, F3x, FPx, FQx, FSx, FTx, FUx, FVx, FWx, FXx v 2519-CTO, 86x, 8Ax v 2522-CTO, 3Bx, 3Kx, 3Lx, 52x, 62x, 63x, 64x v 2537-CTO...
Page 164
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. 1-GB DDR3-1066 SDRAM SO-DIMM (PC3-8500) card 55Y3712 v 2516-CTO, AMx, ANx v 2518-CTO, DWx, DYx, DZx, E4x, E7x, ENx, EPx, EQx, ERx, F4x, G5x, G6x, GSx, GTx v 2519-CTO v 2522-CTO, 30x, 3Kx, 3Lx,, 3Rx, 3Sx, 49x, 54x, 56x, 64x v 2537-CTO, 9Cx v 2538-CTO v 2539-CTO...
Page 167
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. Battery pack, Li-ion (9 cell) 55++ 42T4799 v 2516-CTO, ABx, AEx v 2518-CTO, C4x, C5x, EWx, F2x, F5x, F6x, FGx, FLx v 2519-CTO v 2522-CTO, 30x, 23x, 24x, 2Bx, 2Wx, 3Ax, 3Jx, 3Lx, 3Sx, 3Tx, 3Ux, 3Wx, 3Xx, 43x, 47x, 4Ax, 56x, 64x v 2537-CTO, 23x, 24x, 9Ex v 2538-CTO...
Page 168
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. SATA hard disk drive, 160 GB, 5,400 rpm 45N7205 v 2516-CTO, A6x v 2518-CTO, CPx, CQx, CRx, CSx v 2519-CTO v 2522-CTO v 2537-CTO v 2538-CTO v 2539-CTO SATA hard disk drive, 250 GB, 5,400 rpm 45N7217 v 2516-CTO, A7x, ADx, AFx, AHx, AKx v 2518-CTO, C2x, CHx, CUx, CVx, CWx, CXx, CYx, CZx, D2x, D3x, DCx, DDx, DEx,...
Page 169
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. SATA hard disk drive, 500 GB, 5,400 rpm 45N7221 v 2516-CTO v 2518-CTO, G9x, GDx, GGx, GKx, GMx, GPx v 2519-CTO v 2522-CTO v 2537-CTO v 2538-CTO v 2539-CTO SATA hard disk drive, 500 GB, 5,400 rpm 45N7211 v 2516-CTO v 2518-CTO, G9x, GDx, GGx, GKx, GMx, GPx...
Page 170
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. SATA hard disk drive, 500 GB, 7,200 rpm 45N7257 v 2516-CTO v 2518-CTO, E7x, E8x, ERx, ESx, EVx, EZx, F5x, F8x, F9x, FBx, FCx, FFx, FKx, G6x v 2519-CTO, 89x v 2522-CTO, 3Sx, 3Wx, 3Xx, 42x, 46x v 2537-CTO, 9Cx, 9Ex, 9Fx v 2538-CTO v 2539-CTO...
Page 171
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. MicroSATA solid state drive, 256 GB, FDE 45N8207 v 2516-CTO v 2518-CTO v 2519-CTO v 2522-CTO v 2537-CTO v 2538-CTO v 2539-CTO Modem daughter card (MDC) 43Y6463 System board assembly, integrated graphics, iAMT, TPM 60Y5713 v 2516-CTO, A2x, A6x, A7x, A8x, ADx, AFx, AGx v 2518-CTO, C2x, C3x, C6x, CAx, CBx, CCx, CDx, CHx, CJx, CKx, CLx, CMx, CNx, CPx,...
Page 175
Table 39. Parts list—Overall (continued) FRU (Overall) FRU no. SmartCard Reader 60Y5029 v 2516-CTO v 2518-CTO v 2519-CTO v 2522-CTO, 2Ux, 2Vx, 30x, 3Ex, 62x, 63x, 64x v 2537-CTO, 98x, 99x v 2538-CTO v 2539-CTO SmartCard Reader 60Y5030 v 2516-CTO v 2518-CTO v 2519-CTO v 2522-CTO, 2Ux, 2Vx, 30x, 3Ex, 62x, 63x, 64x...
LCD FRUs In ThinkPad T410 and T410i, there are following types of LCDs. v 14.1-inch WXGA LED-backlight LCD (Table 40 on page 171) v 14.1-inch WXGA+ LED-backlight LCD (Table 41 on page 175) ThinkPad T410 Hardware Maintenance Manual...
Miscellaneous parts Table 43. Parts list—Miscellaneous parts FRU no. Screw kit: 60Y5459 v M2 × 3 mm (silver), small head (50) v M2 × 3.5 mm (black), wafer head (15) v M2 × 5 mm (black), wafer head (15) v M2 × 10 mm (black), wafer head (15) v M2 ×...
Page 188
Table 43. Parts list—Miscellaneous parts (continued) FRU no. System miscellaneous parts: 60Y5458 v (a) Express dummy card v (b) EMI bracket v (c) RJ-11 cable assembly, integrated v (c) RJ-11 cable assembly, discrete v (d) DIMM slot door v (e) Hard disk drive cover for SmartCard model v (e) Hard disk drive cover for non-SmartCard model v (f) SmartCard spacer v (g) Bracket, fan for video...
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 47. Parts list—2-pin power cords Country or region FRU no. Argentina 42T5020 42T5105 * v models -CTO, xxY Brazil 42T5180 42T5183 v models -CTO, xxP...
Recovery discs Windows XP Professional (32 bit) DVDs Windows XP Professional (32 bit) is preinstalled as the operating system in the following models: v 2516-CTO v 2518-CTO, C3x, C5x, CAx, CCx, CEx, CRx, CSx, CWx, CXx, D2x, D3x, D6x, D7x, DAx, DBx, DEx, DFx, DJx, DKx, DNx, DPx, DSx, DTx, F4x v 2519-CTO v 2522-CTO, 36x, 38x, 62x, 63x...
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2516-CTO v 2518-CTO v 2519-CTO v 2522-CTO v 2537-CTO v 2538-CTO v 2539-CTO Table 50. Parts list—Windows Vista Business (32 bit) recovery DVDs Language English 58Y4301...
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2516-CTO, A2x, A3x, A4x, A5x, A7x, A9x, ACx, AFx, AHx, AJx, AKx, ALx, AMx v 2518-CTO, DUx, FYx, G3x v 2519-CTO, 87x v 2522-CTO v 2537-CTO...
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2516-CTO v 2518-CTO, E9x, EDx, FSx, FUx, FWx, GLx v 2519-CTO, 82x, 83x, 84x, 85x, 89x v 2522-CTO v 2537-CTO v 2538-CTO...
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 2516-CTO v 2518-CTO v 2519-CTO v 2522-CTO v 2537-CTO v 2538-CTO v 2539-CTO Table 53. Parts list—Windows 7 Home Premium (64 bit) recovery DVDs Language Czech 58Y4506...
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: v 2516-CTO, A6x, A8x, AAx, ADx, AEx, AGx, ANx v 2518-CTO, C2x, C4x, C6x, C7x, C8x, C9x, CBx, CDx, CFx, CGx, CHx, CJx, CKx, CLx, CMx, CNx, CPx, CQx, CUx, CVx, CYx, CZx, D4x, D5x, D8x, D9x, DCx, DDx, DGx, DHx, DLx, DMx, DQx, DRx, DVx, DWx, DXx, DYx, DZx, E4x, E7x, ELx, EMx, ENx, EPx, EQx, ERx, ESx, EXx, EYx, EZx, F2x, F3x, F5x, F6x, FHx,...
Page 197
Table 54. Parts list—Windows 7 Professional (32 bit) recovery DVDs Language Brazilian Portuguese 58Y4304 Czech 58Y4307 Danish 58Y4308 English 58Y4330 English (for India) 58Y4856 English (modem-disabled) 58Y4329 English, Finnish, and Swedish (in Sweden) 58Y4332 English, French, German, and Dutch (in Belgium and Luxemburg) 58Y4331 English, French, German, and Italian (in Switzerland) 58Y4333...
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: v 2516-CTO, ABx v 2518-CTO, E8x, EAx, EBx, ECx, EEx, EFx, EGx, ETx, EUx, EVx, EWx, FDx, FEx, FFx, FGx, FQx, FTx, FVx, FXx, G7x, G8x, G9x, GEx, GFx, GGx v 2519-CTO v 2522-CTO, 3Fx, 3Gx, 3Tx, 3Ux, 3Yx, 3Zx, 42x, 43x v 2537-CTO...
USB floppy diskette drive for maintenance diskette 05K9283 USB floppy diskette drive tool kit 27L3452 Test card for integrated Smart Card 42W7820 LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later — Note: Download the file from the following Web site: http://www.lenovo.com/ Parts list...
Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System ®...
Page 204
Part Number: 63Y0535 (1P) P/N: 63Y0535...
Need help?
Do you have a question about the 2516AEU and is the answer not in the manual?
Questions and answers