® Document Format (PDF) version from the Lenovo Support Web site at http://www.lenovo.com/support. The Lenovo Support Web site also provides the ThinkCentre Safety and Warranty Guide and this ThinkCentre User Guide in additional languages. Service and upgrades Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center or your documentation.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: •...
For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. •...
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs provided by Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section provides information about the computer features. The following information covers a variety of models.
Page 14
• PCI Fax modem (some models) System management features • Ability to store power-on self-test (POST) hardware test results • Desktop Management Interface (DMI) Desktop Management Interface provides a common path for users to access information about all aspects of a computer, including processor type, installation date, attached printers and other peripherals, power sources, and maintenance history.
Page 15
Input/Output (I/O) features • 9-pin serial port (one standard and one optional) • Eight Universal Serial Bus (USB) connectors (two on the front panel and six on the rear panel) • One Ethernet connector • One DisplayPort connector • One VGA monitor connector •...
Page 16
The operating system(s) listed here are being certified or tested for compatibility at the time this publication goes to press. Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this manual. This list is subject to change. To determine if an operating system has been certified or tested for compatibility, check the Web site of the operating system vendor.
Lenovo. Software provided by Lenovo The following software programs are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer. Software programs provided with your computer might vary depending on your computer model type and preinstalled operating system.
To access the Lenovo ThinkVantage Tools program, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools. The following table lists the programs that you can access from the Lenovo ThinkVantage Tools program. To access a program, double-click the corresponding icon.
• The ThinkVantage Password Manager program is only available on computers with the Windows 7 operating system from Lenovo. • If the Password Vault icon in the Lenovo ThinkVantage Tools program is dimmed, it indicates that you need to install the ThinkVantage Password Manager program manually before enabling its features. To install the ThinkVantage Password Manager program, do the following: 1.
The Adobe Reader program is a tool used to view, print, and search PDF documents. Antivirus software Your computer comes with antivirus software that you can use to detect and eliminate viruses. Lenovo provides a full version of antivirus software on your hard disk drive with a free 30-day subscription. After 30 days, you must renew the license to continue receiving the antivirus program updates.
Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 9 shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1. Front connector, control, and indicator locations Hard disk drive activity indicator USB connector (USB port 1) Power indicator...
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 10 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer.
Page 23
Connector Description Ethernet connector Used to attach an Ethernet cable for a local area network (LAN). Note: To operate the computer within FCC Class B limits, use a Category 5 Ethernet cable. Microphone connector Used to attach a microphone to your computer when you want to record sound or if you use speech-recognition software.
Locating components Figure 3 “Component locations” on page 12 shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 34. Figure 3. Component locations Heat sink and fan assembly PCI card (installed in some models) Memory modules Cover presence switch (also called intrusion switch)
Locating parts on the system board Figure 4 “System board part locations” on page 13 shows the locations of the parts on the system board. Figure 4. System board part locations 4-pin power connector eSATA connector Microprocessor Power fan connector Microprocessor fan connector Front panel connector (for connecting LED indicators and power switch)
Bay 5 - Primary SATA hard disk drive bay (for installing a 3.5-inch hard disk drive or a 2.5-inch solid state drive) Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machine type and model information helps support technicians to identify your computer and provide faster service.
Page 27
The following is a sample of the machine type and model label. Figure 6. Machine type and model label Chapter 1 Product overview...
“Creating recovery media” on page 69. Additionally, in case of a hard disk failure, you can order Product Recovery discs from the Lenovo Customer Support Center. For information about contacting the Customer Support Center, see Chapter 11 “Getting information, help, and service”...
To open the ThinkVantage Fingerprint Software program and use the fingerprint reader, do one of the following: • On the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Fingerprint Reader. • On the Windows Vista operating system, click Start ➙ All Programs ➙ ThinkVantage ➙ ThinkVantage Fingerprint Software.
Each audio solution provides at least three audio connectors: audio line-in connector, audio line-out connector, and Microphone connector. On some models, a fourth connector is provided for the attachment of unpowered stereo speakers (speakers that do not require an ac power source). The audio adapter provides you with the ability to record and play back sound and music, as well as to enjoy sound with multimedia applications and work with speech-recognition software.
If your computer comes with a recordable DVD drive, you can use the drive to record CDs or DVDs. To record a CD or DVD, do the following: 1. Click Start ➙ All Programs ➙ Corel DVD MovieFactory Lenovo Edition. 2. Follow the instructions on the screen.
Page 33
For detailed information about using the Corel DVD MovieFactory program, see the help system for the program. You can also use Windows Media Player to record CDs and data DVDs. For more information, see “Help and Support” on page 111. Chapter 2 Using your computer...
The following topics provide information about arranging your work area, setting up your computer equipment, and establishing healthy work habits: Lenovo is committed to providing people with disabilities greater access to information and technology. As a result, the following information provides ways to help users that have hearing, vision, and mobility limitations get the most out of their computer experience.
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view it without having to twist your body.
Registering your computer also enables Lenovo to notify you about possible technical information and upgrades. When you register your computer, information is entered into a database, which enables Lenovo to contact you in case of a recall or other severe problem. In addition, some locations offer extended privileges and services to registered users.
Page 38
For power cord information and part numbers, go to: http://www.lenovo.com/powercordnotice ThinkCentre User Guide...
Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 7.
The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers. You can order an integrated cable lock directly from Lenovo by searching for Kensington at: http://www.lenovo.com/support Figure 8.
• Administrator Password: Setting an Administrator Password deters unauthorized users from changing configuration settings. If you are responsible for maintaining the configuration settings of several computers, you might want to set an Administrator Password. For more information, see “Administrator Password” on page 78. You do not have to set any passwords to use your computer.
To configure the security chip, you need to download the latest version of the Client Security Solution program from the Lenovo Web site. To download the Client Security Solution program, go to http://www.lenovo.com/support. Then follow the instructions on the screen.
Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. Notes: 1. Use only computer parts provided by Lenovo. 2. When installing or replacing an option, use the appropriate instructions in this section along with the instructions that come with the option.
Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover.
Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1.
Page 48
This section provides instructions on how to install or replace a PCI card. Your computer has two standard PCI card slots, one PCI Express x1 card slot, and one PCI Express x16 graphics card slot. To install or replace a PCI card, do the following: 1.
Page 49
Figure 12. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. b. If the card is held in place by a retaining latch, press the card retaining latch as shown to disengage the latch.
7. Pivot the card latch to the closed position to secure the PCI card. Figure 13. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 67. Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information”...
Page 51
5. Remove any parts that might prevent your access to the memory slots. Depending on your computer model, you might need to remove the PCI Express x16 graphics card for easier access to the memory slots. See “Installing or replacing a PCI card” on page 35. 6.
7. Position the new memory module over the memory slot. Make sure that the notch on the memory module aligns correctly with the slot key on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 16.
Page 53
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button, and then slide the optical drive out of the front of the computer. Figure 17.
6. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 19. Installing the optical drive 7. Connect the signal cable and the power cable to the new optical drive. Figure 20.
This section provides instructions on how to install or replace the card reader. Note: The card reader is only available in some models. For new installation, see “Installing the card reader” on page 43. For replacement, see “Replacing the card reader” on page 45. Installing the card reader To install the card reader, do the following: 1.
Page 56
7. Slide the card reader with retainer into the card reader drive bay until it snaps into position. Figure 23. Installing the card reader 8. Connect the card reader cable to Front USB connector 2 on the system board. See “Locating parts on the system board”...
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 67. Replacing the card reader To replace the card reader, do the following: 1.
8. Slide the new card reader into the drive bay until it snaps into position. Figure 27. Installing the card reader 9. Reconnect the card reader cable to Front USB connector 2 on the system board. See “Locating parts on the system board” on page 13. 10.
2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Locate the battery. See “Locating parts on the system board” on page 13. 4. Remove the old battery. Figure 28. Removing the old battery 5. Install a new battery. Figure 29.
Page 60
Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached.
9. Install and tighten the four screws to secure the power supply assembly. Note: Use only screws provided by Lenovo. 10. Reconnect the power supply assembly cables to the system board and each of the drives.
Page 62
To replace the heat sink and fan assembly, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Lay the computer on its side for easier access to the system board. 4.
a. Partially tighten screw , then fully tighten screw , and then fully tighten screw b. Partially tighten screw , then fully tighten screw , and then fully tighten screw 10. Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board.
Page 64
6. Lift the small handle and open the retainer to access the microprocessor Figure 32. Accessing the microprocessor 7. Lift the microprocessor straight up and out of the microprocessor socket. Figure 33. Removing the microprocessor Notes: a. Your microprocessor and socket might look different from the one illustrated. ThinkCentre User Guide...
Page 65
b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle on one corner of the microprocessor or note the orientation of the notches on the microprocessor. This is important when installing the new microprocessor on the system board. c.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 67. Installing the solid state drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v.
2. To install the solid state drive with the storage converter into the 3.5-inch hard disk drive bracket, flex the bracket and align pin , pin , pin , and pin on the bracket with the corresponding holes in the storage converter. Figure 36.
Page 68
5. Press the blue release tab down, slide the hard disk drive cage to the rear of the computer, and then pivot it outward. Figure 37. Removing the primary hard disk drive 6. Remove the hard disk drive cage from the chassis by sliding it outward. 7.
12. Connect the signal cable and the power cable to the new hard disk drive. 13. Press down on the metal latch and pivot the drive cage into place, and then slide it to the front of the computer until it snaps into position. Note: There are two arrows, one on the upper drive cage and one on the hard disk drive cage.
Page 70
5. Press the blue release button to release the hard disk drive cage from the chassis. Figure 40. Removing the secondary hard disk drive 6. Remove the hard disk drive cage from the chassis by simply sliding it outward. 7. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage. 8.
11. Install the hard disk drive cage into the chassis until it snaps into position underneath the metal tab. Make sure that the hard disk drive cage release button is secured in the chassis. Figure 42. Installing the secondary hard disk drive 12.
Page 72
5. Release the two tabs that attach the front fan assembly to the chassis as shown and then completely remove the front fan from the chassis. Figure 43. Removing the front fan assembly ThinkCentre User Guide...
6. Insert the two tabs of the new front fan assembly into the corresponding holes in the chassis, and press the other two tabs through the holes until the front fan assembly is secured in place. Figure 44. Installing the front fan assembly 7.
Page 74
4. Disconnect the rear fan assembly cable from the system fan connector on the system board. See “Locating parts on the system board” on page 13. 5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis.
7. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 46. Installing the rear fan assembly 8. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: •...
Note: Make sure you note the locations of the cables when you disconnect the cables from the system board. 6. Remove the screw that secures the front audio and USB assembly bracket to the chassis to remove the bracket from the chassis. Figure 47.
Page 77
To replace the internal speaker, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 34. 3. Locate the internal speaker connector on the system board. See “Locating parts on the system board” on page 13.
6. Position the new internal speaker into the four metal clips and push downward on the internal speaker until it is secured in place. Figure 49. Installing a new internal speaker 7. Connect the internal speaker cable to the system board. See “Locating parts on the system board” on page 13.
2. Connect a new keyboard or mouse to one of the USB connectors on the computer. Depending on where you want to connect the new keyboard or mouse, see “Locating connectors, controls, and indicators on the front of your computer” on page 9 or “Locating connectors on the rear of your computer” on page 10. Figure 50.
9. To update your configuration, refer to Chapter 7 “Using the Setup Utility program” on page 77. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Unit (CRU). Information about this will come with the CRU or will come a few days after the CRU arrives.
Recovery program or the Product Recovery program installed. If the Enhanced Backup and Restore icon in the Lenovo ThinkVantage Tools program is dimmed, it indicates that you need to install the Rescue and Recovery program manually before enabling its features. To install the Rescue and Recovery program, do the following: a.
“creating Product Recovery discs.” • To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen.
• To perform a backup operation using the Rescue and Recovery program on the Windows 7 operating system, do the following: 1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens.
• To create a rescue medium on the Windows 7 operating system, do the following: 1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens.
Reinstalling preinstalled applications This section provides instructions on how to reinstall preinstalled applications. To reinstall the selected applications preinstalled on your Lenovo computer, do the following: 1. Turn on the computer. 2. Use Windows Explorer or My Computer to display the directory structure of your hard disk drive.
• To reinstall most commercially available programs in your system, see Microsoft Windows help system for more information. • To reinstall selected application programs that came preinstalled from Lenovo, do the following: 1. Turn on the computer. 2. Use Windows Explorer or My Computer to display the directory structure of your hard disk drive.
5. Open the appropriate application subfolder. 6. In the application subfolder, look for a SETUP.EXE file or other appropriate EXE files for setup. Double-click the file and follow the instructions on the screen to complete the installation. Reinstalling device drivers To reinstall a device driver for an option you installed, refer to the documentation that comes with the option.
Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: •...
Note: A password can be any combination of up to 64 alphabetic and numeric characters. For more information, see “Password considerations” on page 78. Erasing lost or forgotten passwords (clearing CMOS) This section provides instructions on how to erase lost or forgotten passwords, such as a user password. To erase a lost or forgotten password, do the following: 1.
Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device.
• Pressing the power switch • Enabling the wake up on alarm feature The wake up on alarm feature enables your computer to wake up at a set time. To enable the wake up on alarm feature, do the following: 1.
Utility program by starting your computer with a system-program-update disc or running a special update program from your operating system. Lenovo might make changes and enhancements to the POST and BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files.
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update (flash) the BIOS from your operating system, do the following: 1.
Attention: Do not download updated device drivers from the Windows Update Web site. The device drivers provided on the Windows Web site have not been tested by Lenovo and using them might cause unexpected problems. Obtain updated device drivers from Lenovo.
The System Update program helps you keep the software on your computer up-to-date. Update packages are stored on Lenovo servers and can be downloaded from the Lenovo Support Web site. Update packages can contain applications, device drivers, BIOS flashes, or software updates. When the System Update...
• Do not place items on top of the monitor or cover any of the vents in the monitor or computer. These vents provide airflow to keep your computer from overheating. • Keep food and drinks away from all parts of your computer. Food particles and spills might make the keyboard and mouse stick and unusable.
A log book can help you or a Lenovo technician determine if a problem is related to change in hardware, change in software, or some other action that might have taken place.
Page 101
1. Back up all files and data from the hard disk drive. There are a variety of backup programs available commercially. Your operating system also might have a backup program that you can use. Lenovo provides the Rescue and Recovery program to help you back up and restore data. See “Performing backup and recovery operations”...
Note: If you cannot correct the problem, have the computer serviced. For a list of service and support telephone numbers, refer to the ThinkCentre Safety and Warranty Guide that comes with your computer or go to the Lenovo Support Web site at http://www.lenovo.com/support/phone. Symptom...
See Chapter 11 “Getting information, help, and service” on page 111 for more information. • If you are unable to run the diagnostic programs, contact the Lenovo Customer Support Center. See Chapter 11 “Getting information, help, and service” on page 111 for more information.
1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, make sure you review and follow the electrical safety information provided with your computer. For your safety, do not operate the computer with the cover removed. 2.
Note: When external-speaker or headphone cables are attached to the audio connector, the internal speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion slots, the audio function built into the system board is disabled; use the audio jacks on the adapter. •...
An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive Symptom: An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive. Actions: • If you have multiple CD or DVD drives installed (or a combination of CD and DVD drives), try inserting the disc into the other drive.
Page 108
Actions: • Restart the DVD player program. • Close any open files, turn off the computer, and then restart the computer. • Try a lower screen resolution or color depth. If these actions do not correct the problem, run the diagnostic programs (see “Diagnostic programs” on page 108 for instructions).
• Ensure that a DVD disc is in the drive with the shiny side of the disc facing down. • Ensure that video resolution is set to less than 1152 x 864. • On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, make sure that the DVD disc is in the drive labeled “DVD”.
Page 110
1. Click Start ➙ Control Panel. 2. Click Hardware and Sound. 3. Click Devices and Printers. 4. Double-click USB Enhanced Performance Keyboard. The USB Enhanced Performance Keyboard Customization program starts. If these actions do not correct the problem, have the computer and keyboard serviced. See Chapter 11 “Getting information, help, and service”...
• The wireless Keyboard is located less than ten meters away from the transceiver. • The transceiver is fully installed. Action: If the Transceiver Communications LED is not on, reconnect the transceiver and the keyboard. Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments.
If these actions do not correct the problem, run the diagnostic programs (see “Diagnostic programs” on page 108 for instructions). If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 111. The image appears to be flickering Symptom: The image appears to be flickering.
• “Bluetooth problems” on page 102 For more information, see “Help and Support” on page 111. Ethernet problems For Ethernet problems, select your symptom from the following list: • “Your computer cannot connect to the network” on page 101 • “The adapter stops working for no apparent reason”...
Actions: • Make sure that WOL is enabled in the BIOS Setup Utility program. • If it is, check with your LAN administrator for the necessary settings. If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection fails or errors occur Symptom: If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection fails or errors occur.
Windows Vista operating system might be saved as a file with the extension .contact. Option problems Use this information to diagnose problems with Lenovo hardware options that do not have their own troubleshooting information. Select your symptom from the following list: •...
An option that previously worked does not work now Symptom: An option that previously worked does not work now. Actions: • Verify that all option hardware and cable connections are secure. • If the option comes with its own test instructions, use those instructions to test the option. •...
Page 117
– 1. Click Start ➙ Control Panel. 2. Click Programs. 3. Click Turn Windows features on or off. 4. A list of optional Windows components is displayed. Follow the instructions on the screen. – 1. Click Start ➙ Computer. 2. Right-click your C drive entry and then click Properties. 3.
Action: Run the Windows Disk Defragmenter program. Note: Depending on the size of the hard disk drive and amount of data currently stored on the hard disk drive, the disk defragmentation process might take up to several hours to complete. •...
If the problem persists, run the tests described in the documentation that comes with your printer. If you cannot correct the problem, have the computer serviced. See Chapter 11 “Getting information, help, and service” on page 111. Serial port problems Use this information to troubleshoot the serial port and devices attached to the serial port.
– Your computer has the minimum memory requirements needed to use the software. See the information supplied with the software to verify memory requirements. (If you just installed an adapter or memory, you might have a memory-address conflict.) – The software is designed to operate on your computer. –...
3. If you are unable to isolate and repair the problem yourself after running the programs, save and print the log files created by the programs. You will need the log files when you speak to a Lenovo technical support representative.
1. Download a self-starting bootable CD/DVD image (known as an ISO image) of the diagnostic program from: http://www.lenovo.com/support 2. Use any CD/DVD burning software to create a diagnostic disc with the ISO image. Running the diagnostic program from a diagnostic disc This section provides instructions on how to run the diagnostic program from a diagnostic disc that you created.
You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
Read and understand all safety information before using this product. Lenovo Web site The Lenovo Web site provides up-to-date information and services to help you buy, upgrade, and maintain your computer. You can also do the following: •...
You can also get the latest technical information and download device drivers and updates from Lenovo Support Web site at: http://www.lenovo.com/support Calling for service During the warranty period, you can get help and information by telephone through the Customer Support Center.
Service availability and service name might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com...
Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo Rescue and Recovery ThinkCentre ThinkVantage Microsoft, Windows, and Windows Vista are trademarks of the Microsoft group of companies. Intel, Intel Core, Celeron, and Pentium are trademarks of Intel Corporation in the United States, other countries, or both.
• Consult an authorized dealer or service representative for help. Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables and connectors or by unauthorized changes or modifications to this equipment.
Page 130
Geräte der Klasse B. Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart. ThinkCentre User Guide...
Depending on the configuration of your computer and the country or region where the computer was purchased, you might have received additional printed regulatory notices. All regulatory notices are available on the Lenovo Support Web site in electronic format. To access electronic copies of the documentation, go to http://www.lenovo.com/support and click User Guides & Manuals.
Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.com/recycling...
If you want to replace it with a new one, contact your place of purchase or ask for a repair service provided by Lenovo. If you have replaced it by yourself and want to dispose of the disused lithium battery, insulate it with vinyl tape, contact your place of purchase, and follow their instructions.
Customer participation is important to minimize any potential effects of batteries and accumulators on the environment and human health due to the potential presence of hazardous substances. For proper collection and treatment, go to: http://www.lenovo.com/lenovo/environment Appendix C. WEEE and recycling information...
Need help?
Do you have a question about the ThinkCentre M81 and is the answer not in the manual?
Questions and answers