Kenmore 721.86002 Installation Instructions Manual
Microwave hood combination
Hide thumbs
Also See for 721.86002:
- Use and care manual (34 pages) ,
- Use & care manual (33 pages) ,
- Installation instructions manual (21 pages)
Table of Contents
Advertisement
Quick Links
Models/Modelos
721.86002
721.86003
721.86009
Read and save these
installation instructions.
Lea y guarde
estas
instrucciones
de
instalaci6n
iNSTALLATiON
iNSTRUCTiONS
f
INSTRUCCiONES INSTALAGON
lo!
1
f
I
MicrowaveHood Combination
Combinaci6n Microondas C ampana
Part No. MFL57652403
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A
www.sears.com.
Advertisement
Table of Contents
Related Manuals for Kenmore 721.86002
Summary of Contents for Kenmore 721.86002
- Page 1 Models/Modelos 721.86002 INSTRUCCiONES INSTALAGON 721.86003 721.86009 MicrowaveHood Combination Read and save these installation instructions. Combinaci6n Microondas C ampana Lea y guarde estas instrucciones instalaci6n Part No. MFL57652403 Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A www.sears.com.
-
Page 2: Your Safety First
YOUR SAFETY FIRST BEFORE YOU START * Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure 1. - Mounting plate is located on back side of microwave oven. - Page 3 YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having grounding wire with a grounding plug.
- Page 4 YOUR SAFETY FIRST * MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT° - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8"...
- Page 5 PARTS, TOOL MATERIAL5 THE FOLLOWING PARTS ARE SUPPLIED WiTH THE OVEN: you may not use all of these parts. NOTE: Depending on your ventilation requirements clamp Damper/duct connector One power cord (for roof vented or wail vented installation) One dark-colored mounting screw (to hold the power cord)
-
Page 6: Tools And Materials
PARTS, TOOL MATERIAL5 YOU WiLL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE iNSTALLATiON: Carton or other heavy material for covering the counter top. Clear Tape Stud Finder or Thin Nail (for taping the templates to the wail) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof... -
Page 7: Remove The Power Supply
5TEP I: PREPARE THE ELECTRICAl, CONNECTIONE _k WARNING AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. Cabinet NOTE: The outlet should be on a circuit dedicated to the Upper microwave oven 120V, 60Hz., AC only, with a... - Page 8 ETEP 2: PREPARE THE VENTING EYEYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page WARNING- FiRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways: Roof Venting If your oven is located...
-
Page 9: Duct Length
ETEP 2: PREPARE THE VENTING EYETEM STANDARD FiTTiNGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. -
Page 10: Prepare The Venting Blower
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculafing). You need to adjust the blower if you want waJJ vented or roof vented installation. WARNING ELECTRICAL SHOCK HAZARD! UNPLUG UNiT BEFORE WORKING ON iT. - Page 11 STEP 3: PREPARE THE VENTING BLOWER WALL VENTED iNSTALLATiON: back plate blower unit 1. Remove blower unit mounting screw(s) and blower plate screw(s). Remove the blower plate from blower plate mounting screw(s) cabinet. See Figure 12. (option) 2. Carefully lift the blower unit out of the microwave oven.
-
Page 12: Roof Vented Installation
STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED iNSTALLATiON: plate 1. Remove blower unit mounting screw(s) and blower mounting screw(s) (option) plate screw(s). Remove the blower plate from cabinet. See Figure 18. 2. Carefully lift the blower unit out of the microwave oven. - Page 13 STEP 4: PREPARE THE WALl. AND UPPER CABINET FOR INSTALI.ATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line _V) on the back wail, as in Figure 22. 2.
- Page 14 STEP 4: PREPARE THE WALl. AND UPPER CABINET FOR INSTALI.ATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. WARNING BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock.
- Page 15 STEP 5: INSTALL THE MOUNTING PLATE TO THE WALl. 3/16"Hole on Studs THE OVEN MUST BE CONNECTED 5/8"Hole on Drywall Only Minimum 66"1 TO AT LEAST ONE WALL STUD. 1. Draw a vertical line on the wan at the center of the 30"...
- Page 16 STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: * Make the box cutout for the rear wail duct. - I piece mounting plate: Using a pencil, put dots through slots F and...
- Page 17 ETEP 6: A TTACH THE 0 VEA! TO THE WAl.l. WARNING You will need two people to lift this cord microwave. Failure to use more than one person could result in personal injury. power cord hole 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the...
- Page 18 ETEP 6: A TTACH THE 0 VEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the \_damper'/ upper cabinet. Complete the venting system through the roof according to the method needed. "PREPARE THE VENTING SYSTEM,"...
- Page 19 MEMO...
- Page 20 Printed in Korea...
Need help?
Do you have a question about the 721.86002 and is the answer not in the manual?
Questions and answers