AUDIO PERFORMANCE POWER CONSUMPTION Line outputs Test equipment:Audio Precision System2 Power-Supply:100-240V ac,50/60Hz, Test discs:CDDA:Philips audio signal test disc 1 Supply voltage:AC 100~240V DVD: Philips LVP 9.01 audio test disc Supply Power consumption(AC 100/240V):10W/+10% Load Impedance:100KΩ for Audio Standby Power,230V AC: <1W...
Page 3
DVD BOARD 8W/2P POWER BOARD DECK AMI POWER SW BOARD KEY BOARD USB BOARD VERSION VARIATIONS Type/Versions: DVP3111 Service policy Board in used: DVD BOARD USB BOARD POWER SW BOARD *TIPS: C -- Component Lever Repair. M -- Module Lever Repair...
Page 4
Select “0” setting = Region Free (confidential) Procedure for SW upgrade 1. The upgrade will provide a document re-named: PHILIPS.BIN “PHILIPS.BIN” copy to USB or CD-ROM into the data; 3. Reading the USB or CD-ROM,in accordance with prompt,press ”OK” key to upgrade.
2.0 Safety instruction 1. General safety 2. Laser safety Safety regulations require that during a repair: This unit employs a laser. Only qualified service . Connect the unit to the mains via an isolation personnel transformer. May remove the cover, or attempt to service this .
4.0 MECHANICAL AND DISMANTLING INSTRUCTIONS The following guidelines show how to dismantle the player. Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover(Figure1) Figure 1 Step2:If the tray can’t open in normal way, you can make it through the instruction as below (Figure2) Figure 2 Step3: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first(Figure3) Figure 3...
Page 8
4.0 MECHANICAL AND DISMANTLING INSTRUCTIONS Step4: Remove the 10 screws on board to dismantle the DVD BOARD & POWER BOARD & LED BOARD (Figure 4&5) Figure4 Figure 5...
Trouble shooting chart Spindle motor does not move Motor not move Check the FFC connection Correct connection between 24P and the loader. Check whether “MO_VCC” Check the MOVCC power (VCC) voltage is normal. supply Check whether laser voltage Check/Replace Q10 Q11. (1.9V for CD &...
Page 10
Trouble shooting chart The power can not be on or off The power can’t be on or off Check the power supply Replace the power board on the power board and the connection to or correct the connection to decoder board is normal. Check if the CON2 on the front Check/Correct connection board to J 6(7PIN) on the decoder board...
Page 11
Trouble shooting chart Disc cannot be read . Disc cannot be read. Check the FFC connection Check the loaded circuit between 24P and the loader. 1.Check voltage on pin 23 of U2 varies between 0 and 3.3V: Check whether there is 3.3V for CD laser voltage (1.9V for CD 0V for DVD...
Page 12
Trouble shooting chart Only DVD disc or only disc except DVD can be played Only DVD disc, or only disc except DVD can be Played. Check Check the loaded circuit connection between 24pin and the loader. Check laser voltage (1.9V) output on Collector of Q11, if Check the solder status on U2 and pin 17 of U2 is at low level.
Page 13
Trouble shooting chart Distorted audio and loud noise Distorted audio and loud noise Check he power supply voltages +12V Replace L2 to the operation amplifying L2 are normal Check whether Replace Q12, Q14 muting transistors Q12, Q14, are normal Checking the U2 leads the feet has no to break Correct connection to open...
Page 14
Trouble shooting chart Abnormal color of video picture Abnormal color of video picture Check whether the 27MHz Check Y1, R17, C21 and C22 output signal is normal. Check whether the 3.3V Check other of power supply electric and 1.8V power supply circuit voltages on the decoder board are normal.
Page 15
Trouble shooting chart Remote reception is insensitive or fails. Remote reception is insensitive or fails. Check if the remote Check battery control works properly. Check power Check R1 R2 on front board supply voltage to the remote censor is normal Use an oscilloscope to check if there is output waveform IR1(PIN 3 - RCwaveform)
Page 16
Trouble shooting chart No video picture, no sound. No video picture, no sound. Check whether voltages from the power Check the loaded circuit board to the decoder board are normal. CVBS(L27 point) waveform Check if the reset circuit consisting of C13, Q4, Q3,R11,R12,R13,R15,R16 is normal Change C13,Q4,Q3 (at a high level for tens of milliseconds, then constantly at 0V).
Page 17
Trouble shooting chart No display on LED, and buttons do not work LED and buttons do not work Check whether there is correct contact Correct connection between CON1 of front board and J 6 of decoder board Check DV33(+3.3V) Fix power supply board top voltage on the power a power supply for should and front board...
Page 33
996510028604 DVD DOOR BLACK 996510028626 LED LENS WHITE 996510028626 LED LENS WHITE 996510028071 OPEN BUTTON BLACK 996510028617 IR KENS BLACK 996510028673 FRONT PANEL DARK GREY DVP3111-98/77 STANDBY PCB PARTS LIST 12NC No. Part Name 996510028602 STANDBY PCBA ASS'Y 996510028072 TACT SWITCH 6*6*5mm LED3 996510028067 DIP LED RED 1.8VD3...
Page 34
8.0 SERVICE PA RT LIST DVP3111-98/77 DVD MAIN PCB PARTS LIST 12NC No. Part Name 996510028599 DVD MAIN PCBA 996510028064 IC SW5888 HSOP28 5CHA 996510028051 IC YD4558 SOP8PIN 996510028043 IC W9864G6XH6 996510028615 IC EN25B1675HCP SOP8 16M 996510028622 IC MT1389DEXLA LQFP128...
Need help?
Do you have a question about the DVP3111 and is the answer not in the manual?
Questions and answers