SECURITE DU FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES SONY PARTS WHOSE PART NUMBERS APPEAR AS COMPOSANTS SONY DONT LE NUMERO DE PIECE EST INDIQUE DANS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS LE PRESENT MANUEL OU DANS DES SUPPLEMENTS PUBLIES PAR SONY.
Page 5
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C No. of times Self-diagnostic Diagnostic STANDBY/STEREO Display/ Probable Cause Location Detected Symptoms Item/Description LED flashes Diagnostic result • +5 line is overloaded. (A, B Boards) • No picture LOW B OCP/OVP 6 times 6:0 or 6:1 • +5 line is shorted. (A, B Boards)
Page 6
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Handling of Self-Diagnostic Screen Display Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to “0”. Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs.
Page 7
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SAFETY CHECK-OUT After correcting the original service problem, perform the Leakage Test following safety checks before releasing the set to the The AC leakage from any exposed metal part to earth customer: ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5...
CATV cable (unscrambled channels) ✍ Coaxial cable Your Sony remote control can be programmed to operate your cable box (see “Programming the Remote Control” on page 42). When using Favorite Channel or Twin View, you cannot view the AUX input in the window picture.
Page 9
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Installing the TV Installing the TV Connecting a VCR and Cable Box Connecting a Satellite Receiver Connect the single (input) jack of the splitter to your incoming Connect the satellite antenna cable to the satellite receiver’s cable connection, and connect the other two (output) jacks (using SATELLITE IN jack.
Page 10
Connecting a Digital TV Receiver Using the CONTROL S Feature Using three separate component video cables, connect the Digital CONTROL S allows you to control your TV system and other Sony TV Set-top box’s Y, P , and P jacks to the TV.
Page 11
Audio 314, 337 Optimus Dynamic Panasonic 704, 710 If you have video equipment other than Sony brand that you want to Panasonic 308, 309, 306, Pioneer Broksonic 319, 317 control with the TV’s remote control, use the following procedures to...
Page 12
Press TV (FUNCTION) when operating your TV. If, after reading these operating instructions, you have additional questions related to the use of your Sony ❏ Make sure the TV’s power cord is connected securely to the wall outlet.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SECTION 2 DISASSEMBLY 2-1. REAR COVER REMOVAL Remove +BVTP 4x16 screws from areas indicated with a circle. * = screws for 36" and 38" models only. 2-2. CHASSIS ASSEMBLY REMOVAL 2-3. SERVICE POSITION CAUTION! Heat sink on IC5004 is -15V.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 2-4. PICTURE TUBE REMOVAL WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is discon- nected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SECTION 3 SET-UP ADJUSTMENTS Perform the adjustments in order as follows: The following adjustments should be made when 1. Beam Landing a complete realignment is required or when a new picture tube is installed. 2. Convergence 3. Focus These adjustments should be performed with rated 4.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 3-2. V-PIN and V-CEN ADJUSTMENT Operation of BMC (Hexapole) Magnet Before beginning adjustment procedure: The respective dot positions resulting from moving each • magnet interact, so perform the following adjustment while Input a cross hatch pattern signal. tracking. •...
Page 17
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Screen-Corner Convergence 3. RSAP (RIGHT AMP) • Input crosshatch pattern. 1. Affix a permalloy assembly corresponding to the misconverged areas. 4. RUBW (RIGHT SIDE UPPER C-BOW) 5. RLBW (RIGHT SIDE BOTTOM C-BOW) 6. LSAP (LEFT AMP) Dynamic Convergence Adjustments...
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 3-6-1. VIDEO INPUT -Two Picture Sub 3-4. FOCUS ADJUSTMENT Contrast Adjustment 1. Input Monoscope signal. 1. Input a Color Bar signal to VIDEO 1 (75 IRE 75%). 2. Set VIDEO MODE: Standard (RESET). 2. Set picture mode: P&P (PRO MODE).
Page 19
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 3-6-3. RF INPUT Two Picture Sub Contrast 3-6-2. VIDEO INPUT - Sub Hue/Sub Color Adjustment Adjustment 1. Input a Color Bar signal to RF (75 IRE 75%). 1. Input a Color Bar signal to VIDEO 1 (75 IRE 75%).
Page 20
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 6. Adjust SUB (right) side contrast according to service mode 4. Connect oscilloscope to Pin 5 of CN9001 (B. DRV) on C for SCON. Board. 5. Adjust MAIN (left) side color according to service mode for SCOL. 2103-2 Name Control Function 6.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 3-9. PICTURE DISTORTION ADJUSTMENTS 3. Adjust white balance in the service mode and set the following data: 3-9-1. NTSC (DRC) Full mode adjustment 2150P-1 1. Face picture tube to east or west direction. Name Control Function Avg. Data 2. Complete VPIN and VCEN adjustment first. (A2150-D1 05...
Page 22
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C 3-9-2. 1080i HD mode adjustment CXA2150D-2 1. Input a 1080i HD cross-hatch signal and an HD monoscope HPOS (H-POSITION) signal that contains overscan markers. 2. Adjust raster position per section 3-8 only if this procedure was not performed for full mode.
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SECTION 5 CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y74) to perform the circuit adjustments in this section. NOTE: Test Equipment Required: 1) Pattern generator 2) Frequency counter 3) Digital multimeter 4) Audio oscillator 5-1. SETTING THE SERVICE ADJUSTMENT MODE 5-2.
5-4. SERVICE DATA LISTS DX1A Service List ------ Contents & Notes Category Number & Name Device Name Device Reference Number Slave Address Comment µPD64082 3D-COMB IC3501 / BC-board B8h (W) & B9h (R) W&R: Write & Read # 2-1 CXA2103-1 (Main) IC3048 (Main) / B-board CXA2103Q # 2-2...
Page 26
3D-COMB / µPD64082 DX1A SERVICE LIST (#1): (Part-1/2) µ Device Name: PD64082GF { 3D-Comb Filter / NEC } / IC3501 (BC-board) / P/N: 8-759-594-44 (SB#: V7372) Slave Address: B8h (Write Address) / B9h (Read Address) Register Control Register Data Data Data Initial/Average Setting Comment No &...
Page 27
3D-COMB / µPD64082 DX1A SERVICE LIST (#1): (Part-2/2) Register Control Register Data Data Data Initial/Average Setting Comment No. & Name (32V&36V CRTs) Function & Link Type Range SNNR Setting-based Control Table for YHCO & YHCG SNNR = 0 SNNR = 1 SNNR = 2 SNNR = 3 (Not SNNR Offset Data)
Page 28
CXA2103-1 {Main} DX1A SERVICE LIST (#2-1): Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3048 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Ah { Main } Register Control Register Data Data Data Initial Setting & [Average Data]...
Page 29
CXA2103-2 {Sub} DX1A SERVICE LIST (#2-2): Device Name: CXA2103Q { NTSC-YCT (Chroma Decoder) / SONY } / IC3110 (B-board) / P/N: 8-752-089-50 (SBorSD#: NA) Slave Address: 9Eh { Sub } Register Control Register Data Data Data Initial Setting & [Average Data]...
Page 30
CXA2150P-1 {Picture Controls: P1 DX1A SERVICE LIST (#3-1): Device Name: CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h Register Control Register Data Data Data Initial Settings & [Average Data] Comment No &...
Page 31
CXA2150P-2 {Picture Controls: P2 DX1A SERVICE LIST (#3-2): Device Name: CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Register Control Register Data Data Data Initial/Average Settings No & Name Function & Link Type...
Page 32
CXA2150P-3 {Picture Controls: P3 DX1A SERVICE LIST (#3-3): (Part-1/3) Device Name: CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h Data Initial/Average Settings (32V&36V CRTs) Register Control Register Data Data Picture Mode: Vivid Comment No &...
Page 33
CXA2150P-3 {Picture Controls: P3 DX1A SERVICE LIST (#3-3): (Part-2/3) Data Initial/Average Settings Data Initial/Average Settings Data Initial/Average Settings (32V&36V (32V&36V (32V&36V CRTs) CRTs) CRTs) Register Note Picture Mode: Standard Picture Mode: Movie Picture Mode: Pro No & Name YPbPr YPbPr YPbPr YPbPr YPbPr...
Page 34
CXA2150P-3 {Picture Controls: P3 DX1A SERVICE LIST (#3-3): (Part-3/3) Data Initial/Average Settings (32V&36V CRTs) Register Comment SNNR=0 SNNR=1 SNNR=2 SNNR=3 No & Name (Offset) (Offset) (Offset) (Offset) #1 UVML (cont.) #3 VMCR (cont.) #10 F1LV (cont.) #11 CDSP (cont.) #12 LTLV (cont.) #14 CTLV (cont.) #19 MIDE (cont.)
Page 38
CXA2150D-1 {Deflection Controls: D1} DX1A SERVICE LIST (#4-1): Device Name: CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h Register Data Initial Settings & [Average Data] Control Register Data Data Comment No &...
Page 39
CXA2150D-2 {Deflection Controls: D2} DX1A SERVICE LIST (#4-2): Device Name: CXA2150Q { CRT Driver / SONY } / IC201 (A-board) / P/N: 8-752-093-35 (SBorSD#: NA) Slave Address: 86h Register Control Register Data Data Data Initial Settings & [Average Data] Comment No &...
Page 40
AKBTIM: AKB timing 0~31 Note: CXA2151Q DX1A SERVICE LIST (#5): Device Name: CXA2151Q { Component I/F & Sync Seperation / SONY } / IC3001 (B-board) / P/N: 8-752-093-84 (SD#: S00302B) Slave Address: 84h Register Control Register Data Data Data Initial/Average Settings Comment No &...
Page 41
D-CONV / CXA8070 DX1A SERVICE LIST (#6): Device Name: CXA8070AP { DY-Convergence Control / SONY } / IC5513 (D-board) / P/N: 8-759-595-52 (SB#: V1718) Slave Address: DEh Register Control Register Data Data Data Initial Settings & [Average Data] Comment No & Name Function &...
Page 42
Audio Processing (AP) / BH3868FS DX1A SERVICE LIST (#8): Device Name: BH3868FS { Audio Processor / ROHM } / IC7001 (A-board) / P/N: 8-759-678-92 (SBorSD#: NA) Slave Address: 82h Register Control Register Data Data Data Initial/Average Setting Comment No & Name Function &...
Page 45
MID-3 (VDO-in Data) DX1A SERVICE LIST (#12): (Part-2/2) Register Data Initial Setting Data Initial Setting Comment No & Name (32V&36V CRTs) (32V&36V CRTs) MID Mode: P&P / Favorite MID Mode: FREEZE YPbPr YPbPr Dummy YPbPr YPbPr Dummy Dummy-480i settings are used for No Signal cases. 480i 480P 1080i...
Page 47
MID-5 (Picture Data: MIDE) DX1A SERVICE LIST (#13): (Part-2/4) Register Data Initial/Average Setting Data Initial/Average Setting Comment (32V&36V CRTs) (32V&36V CRTs) No & Name YPbPr-480p YPbPr-1080i Movie Standard Vivid Movie Standard Vivid #0 POP (cont.) #1 MHLY (cont.) #2 MHLC (cont.) #3 MVLY (cont.) #4 MVLC (cont.) #5 MHYR (cont.)
Page 48
MID-5 (Picture Data: MIDE) DX1A SERVICE LIST (#13): (Part-3/4) Register Control Register Register Name Data Data Data Initial/Average Setting Data Initial/Average Setting No.&Name Function & Link (Software) Type Range (32V&36V CRTs) (32V&36V CRTs) UHF/VHF & CV YPbPr-480i (DVD) Settings for P&P (Sub) Movie Standard Vivid...
Page 49
On-Screen Display (OSD) DX1A SERVICE LIST (#14): Device Name: M306V2ME-150FP or M306V2ME-151FP { System Micro (MASK type) / Mitsubishi } / IC701 (A-board) (V1.0) (V2.0) Slave Address: 60h System Micro (MASK type): M306V2ME-150FP, Sys-Software: Version 1.0 (used with Patch-B), P/N: 8-759-680-77 (SB#: V9091) System Micro (MASK type): M306V2ME-151FP, Sys-Software: Version 2.0 (used with Patch-A), P/N: 8-759-699-34 (SB#: V9091) Register Control Register...
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SECTION 6 DIAGRAMS 6-2. CIRCUIT BOARDS LOCATION • When replacing components identified by , make the necessary adjustments indicated. If results do not meet the specified value, change the component identified by and repeat the adjustment until the specified value is achieved. (Refer to safety adjustments on Page 23.) 6.1 BLOCK DIAGRAM (1/4)
Page 57
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C BLOCK DIAGRAM (3/4) D6516 T6501 AU RECT CN6501 200V Y/C SEP IC3501 AC RECT+ IC3500 AU +24V AUTO WIDE 3D COMB/HH DEC MEMORY CN3201 CN3500 AC RECT- C IN Q3508 FL3501 Q3509 +135V BUFF BUFF MIO0 IO08 PRI 15V...
Page 58
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C [ TUNER, CRT DRIVE, MAIN UCOM, POWER SUPPLY, AUDIO ] COMPONENT SIDE BLOCK DIAGRAM (4/4) A BOARD LOCATOR LIST DIODE Component Conductor Component Conductor Side Side Side Side CN5501 TO D BOARD D004 IC201 H-11 D008 IC701 CN706 CN003...
Page 59
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C A BOARD SCHEMATIC DIAGRAM (1 of 3) [ TUNER, CRT DRIVE, MAIN UCOM, POWER SUPPLY, AUDIO ] CONDUCTOR SIDE A BOARD IC VOLTAGE LIST IC201 volt TU001 BTF-FA402 TU002 BTF-WA412 S-L/R C002 R008 R037 R049 Q015 4.7k :CHIP 2SD601A...
Page 60
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C A BOARD IC VOLTAGE LIST A BOARD TRANSISTOR A BOARD SCHEMATIC DIAGRAM (2 of 3) VOLTAGE LIST IC701 IC702 volt volt Q701 C BOARD WAVEFORMS Q702 CN701 CN702 CN703 Q703 :S-MICRO :B-TO-B :B-TO-B Q704 TO H5 CN4301 TO H8 CN4301...
S BOARD LOCATOR LIST A BOARD TRANSISTOR A BOARD (*) MODEL VARIANCE LIST VOLTAGE LIST DIODE A BOARD IC VOLTAGE LIST COMPONENT SIDE CONDUCTOR SIDE Component Conductor REF NO. LOC KV-32XBR400 KV-36XBR400 KV-38DRC1C IC6001 IC6002 IC6011 IC7002 D4101 C6002 0.22 125V 0.22 125V 0.22 300V...
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C B BOARD TRANSISTOR B BOARD IC VOLTAGE LIST VOLTAGE LIST IC3201 B Board Schematic Diagram (1 of 4) volt Q3201 Q3202 Q3203 Q3204 Q3205 Q3206 Q3207 -1.0 Q3208 -0.3 Q3209 -0.3 BS 9V Q3210 C3229 C3235 R3261 R3263 Q3211 3.3k...
Page 64
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C B BOARD IC VOLTAGE LIST IC3001 IC3003 IC3004 IC3089 IC3601 IC3602 IC3603 B Board Schematic Diagram (2 of 4) volt volt volt volt volt volt volt L3603 C3618 C3619 :CHIP :AL-CP F:1608 FL3003 IC3090 IC3091 C3008 0.47 R3648 C3004...
Page 65
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C B Board Schematic Diagram (3 of 4) B BOARD IC VOLTAGE LIST IC3301 IC3302 volt volt RB3306 RB3307 56*4 56*4 IC3304 volt IC3303 3.3V volt C3301 L3301 :CHIP F:1608 3.3V C3302 C3303 XRAS XCAS 6.3V :AL-CP F:1608 IC3301 MSM56V16160F...
Page 66
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C B Board Schematic Diagram (4 of 4) B BOARD IC VOLTAGE LIST IC3401 IC3404 IC3413 volt volt volt 3.3V R3401 R3403 1.2k 3.3V 1/16W 1/16W :RN-CP :RN-CP 3.3V IC3402 2.5V L3401 MB81F643242B-D C3406 0.01 :CHIP 64M-SDRAM B:CHIP IC3402 C3401 3.3V...
Page 77
SPEAKER BOX (R) TYPE 5X9CM KV-36XBR400/38DRC1/38DRC1C/36XBR400H only) A-1391-048-A S BOARD, MOUNTED 1-500-386-11 FILTER, CLAMP (FERRITE CORE) KV-32XBR400 /36XBR400/38DRC1/36XBR400H only) 4-075-830-01 BRACKET, EARLY 32XBR PRODUCTION CONFIGURATION CURRENT CONFIGURATION IF HV BLOCK ASSY OR FBT NEEDS REPLACEMENT, USE FBT ASSY. P/N 1-453-346-11 (NX-6000//J1J4) FBT ASSY# 1-453-346-11 (SHOWN TO THE RIGHT).
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C SECTION 8 Note: ELECTRICAL PARTS LIST The components identified by shading The components identified by in this manual and mark are critical for safety. • All variable and adjustable resistors have have been carefully factory-selected for each set Replace only with part number specified.
Page 94
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une piece portant le Replace only with part number specified.
Page 96
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une1 piece portant le Replace only with part number specified.
Page 97
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK C7063 1-136-165-00 FILM 0.1µF *CN6013 1-766-240-11 PIN, CONNECTOR (PC BOARD) C7064 1-126-953-11 ELECT 2200µF 20% 35V *CN7001 1-573-296-21 CONNECTOR, BOARD TO BOARD 10P C7066 1-136-165-00 FILM 0.1µF *CN7003 1-564-511-11 PLUG, CONNECTOR...
Page 103
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une piece portant le Replace only with part number specified.
Page 104
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une1 piece portant le Replace only with part number specified.
Page 106
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une1 piece portant le Replace only with part number specified.
Page 110
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R5070 1-216-113-00 RES-CHIP 470K 1/10W R5013 1-216-393-00 METAL OXIDE R5071 1-208-810-11 METAL CHIP 0.50% 1/10W R5014 1-208-790-11 METAL CHIP 2.2K 0.50% 1/10W R5072 1-208-810-11 METAL CHIP 0.50% 1/10W R5016...
Page 111
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C REF.NO. PART NO. DESCRIPTION REMARK REF.NO. PART NO. DESCRIPTION REMARK R5511 1-216-295-11 SHORT R5124 1-216-295-11 SHORT R5512 1-216-065-91 RES-CHIP 4.7K 1/10W R5125 1-216-065-91 RES-CHIP 4.7K 1/10W R5513 1-216-065-91 RES-CHIP 4.7K 1/10W R5126 1-216-025-11 RES-CHIP 1/10W R5514 1-216-295-11 SHORT R5127...
Page 112
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une piece portant le Replace only with part number specified.
Page 113
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une piece portant le Replace only with part number specified.
Page 114
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C The components identified by in this manual have The components identified by shading been carefully factory-selected for each set in order and mark are critical for safety. to satisfy regulations regarding X-ray radiation. Should Replace only with part number specified.
Page 115
KV-32XBR400/36XBR400/36XBR400H/38DRC1/38DRC1C Les composants identifies per un trame et une The components identified by shading marque sont critiques pour la securite. Ne and mark are critical for safety. les remplacer que par une1 piece portant le Replace only with part number specified.
Need help?
Do you have a question about the Trinitron KV-32XBR400 and is the answer not in the manual?
Questions and answers