Advertisement
Quick Links
Download this manual
See also:
Operating Manual
SERVICE MANUAL
NTSC
Models 36SDX01SR/36SDX01S and 36SDX88B are in the same Solid State Color Television fam-
ily. The main difference between the 36SDX01SR/36SDX01S and 36SDX88B is the control panel
and the CRT. Please refer to model 36SDX88B schematics, assembly, wiring, test and trou-
bleshooting information when servicing models 36SDX01SR/36SDX01S. Refer to Service Manual
PA No. 0110 issued in December 1998.
Please refer to Service Manual PA No. 0110 when adjusting 36SDX01SR/36SDX01S. The only difference is the Chopper Voltage as
stated below.
SYMBOL
DESCRIPTION
NO.
#
CHOPPER VOLTAGE ADJUSTMENT
(PA No. 0110 SECTION 2.3.1 PAGE 47)
RT01
FOCUS ADJUSTMENT
(PA No. 0110 SECTION 3.3 PAGE 81)
36SDX01S/MM1T ONLY
5. Vertical Line Adjustment
Adjust Focus on Cross-Hatch Circle Pattern focusing
the point as shown in the right figure.
6. Adjust RT01 focusing only at vertical line so that it
becomes the most thick; the adjustment point which
can be seen the clearest without any saturation.
Concentration point:
Inner point of the circle as shown in the fight figure.
Note:
Adjust Horizontal Center Focus again after adjusting
Vertical Focus.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
S O L I D S TAT E C O L O R T E L E V I S I O N
MAY 2000
MM1R/MM1T
ADJUSTMENT
36SDX88B/MM1
VGA MODE=112±0.5V
DTV MODE=124±0.5V
SVGA MODE=140±0.5V
SAME AS STATED
IN PA No. 0110.
PA
36SDX01SR/MM1R
36SDX01S/MM1T
R/C: CLU-433FC
36SDX01SR/MM1R
VGA MODE=112±0.5V
DTV MODE=124±0.5V
SVGA MODE=140±0.5V
SAME AS STATED
IN PA No. 0110.
The end of
Cross-Hatch
The second vertical line from
the left end.
HHEA-MANUFACTURING DIVISION
No. 0140
36SDX01S/MM1T
VGA MODE=105±0.5V
DTV MODE=120±0.5V
SVGA MODE=135±0.5V
SEE BELOW
CPT PWB
RT01
REAR VIEW
Advertisement
Related Manuals for Hitachi 36SDX01SR
Summary of Contents for Hitachi 36SDX01SR
-
Page 1: Service Manual
36SDX01SR/36SDX01S. Refer to Service Manual PA No. 0110 issued in December 1998. ADJUSTMENT Please refer to Service Manual PA No. 0110 when adjusting 36SDX01SR/36SDX01S. The only difference is the Chopper Voltage as stated below. SYMBOL... -
Page 2: Replacement Parts List
36SDX01SR/MM1R AND 36SDX01S/MM1T ONLY PARENTAL CONTROL (V-Chip) operation check Receive Signal TV-PG MPAA PG TV-Y7-FV Preparation for Adjustment Picture/Audio BLOCK UNBLOCK UNBLOCK (1) Receive a channel with V-Chip signal. Condition (2) Push MENU and select CUSTOM menu by using (5) Select MOVIE RATINGS MPAA (PG-13) and TV button. - Page 3 ÒSafety PrecautionsÓ and ÒProduct Safety NoticesÓ in this Service Manual. Do not degrade the safety of the receiver through improper servicing. SYMBOL DESCRIPTION 36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T I001 MAIN MICRO-CONTROLLER CP05361...
- Page 4 ÒSafety PrecautionsÓ and ÒProduct Safety NoticesÓ in this Service Manual. Do not degrade the safety of the receiver through improper servicing. SYMBOL DESCRIPTION 36SDX88B/MM1 36SDX01SR/MM1R 36SDX01S/MM1T RL12 RESISTOR 0700033M...
-
Page 5: Printed Circuit Board
PRINTED CIRCUIT BOARD CPT P.W.B. - Page 6 NOTES:...
- Page 7 PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to POWER DEFLECTION BASIC CIRCUIT DIAGRAM safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service SIGNAL 1 OF 3 Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 8 POWER DEFLECTION BASIC CIRCUIT DIAGRAM SIGNAL 1 OF 3 PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 9 PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to SIGNAL 2 OF 3 BASIC CIRCUIT DIAGRAM safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service SIGNAL 3 OF 3 Manual.
- Page 10 SIGNAL 2 OF 3 BASIC CIRCUIT DIAGRAM PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to SIGNAL 3 OF 3 safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual.
- Page 11 PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to TUNER BASIC CIRCUIT DIAGRAM safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 12 TUNER BASIC CIRCUIT DIAGRAM PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 13 PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to BASIC CIRCUIT DIAGRAM safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service CONTROL PANEL Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 14 BASIC CIRCUIT DIAGRAM PRODUCT SAFETY NOTE: Components marked with a and shaded have special characteristics important to CONTROL PANEL safety. Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. DonÕt degrade the safety of the receiver through improper servicing. All DC voltage to be measured with a tester (100k /V).
- Page 15 NOTES:...
Need help?
Do you have a question about the 36SDX01SR and is the answer not in the manual?
Questions and answers