HISTORY INFORMATION FOR THE FOLLOWING MANUAL: DA-4 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO. KV-34DRC430 RM-Y197 LATIN NORTH SCC-S71N-A KV-34DRC430 RM-Y197 LATIN SOUTH SCC-S71P-A KV-36DRC430 RM-Y197 LATIN NORTH SCC-S71Q-A KV-36DRC430 RM-Y197 LATIN SOUTH SCC-S71R-A ORIGINAL MANUAL ISSUE DATE: 3/2005...
Page 2
Self Diagnosis Supported model DA-4 SERVICE MANUAL CHASSIS MODEL NAME REMOTE COMMANDER DESTINATION CHASSIS NO. KV-34DRC430 RM-Y197 LATIN NORTH SCC-S71N-A KV-34DRC430 RM-Y197 LATIN SOUTH SCC-S71P-A KV-36DRC430 RM-Y197 LATIN NORTH SCC-S71Q-A KV-36DRC430 RM-Y197 LATIN SOUTH SCC-S71R-A RM-Y197 KV-36DRC430 ® TRINITRON COLOR TELEVISION...
SRS (SOUND RETRIEVAL SYSTEM) is manufactured TruSurround is a trademark of SRS Labs, Inc. SRS and the SRS by Sony Corporation under license from SRS Labs, Inc. It is symbol are registered trademarks of SRS Labs, Inc. in the United covered by U.S.
Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identifi ed in this manual. Follow these procedures whenever critical components are replaced or improper operation is suspected.
KV-34DRC430/36DRC430 SAFETY CHECK-OUT Leakage Test After correcting the original service problem, perform the following The AC leakage from any exposed metal part to earth ground and from safety checks before releasing the set to the customer: all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
KV-34DRC430/36DRC430 Self Diagnosis SELF-DIAGNOSTIC FUNCTION Supported model The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to fl ash. The number of times the LED fl ashes translates to a probable source of the problem. A defi nition of the STANDBY/TIMER LED fl ash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 9
KV-34DRC430/36DRC430 Self-Diagnostic Screen Display For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confi rmed, it is possible to bring up past occurrences of failure on the screen for confi rmation.
Page 10
KV-34DRC430/36DRC430 +B overcurrent (OCP) Occurs when excessive current fl ows through R5013. The increase in voltage across R5013 causes the output of Q5004 to go high, and this high signal goes to the micro. +B overvoltage (OVP) IC6505 detects +B OVP condition and turns on Q6522. This sends a high signal to the micro and also shuts down the AC relay.
KV-34DRC430/36DRC430 1-4. PICTURE TUBE REMOVAL WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, Coated discharge CRT before attempting to remove the anode cap. Short between anode and CRT...
KV-34DRC430/36DRC430 CABLE WIRE DRESSING NOTE: IF THE WIRE DRESSING IS NOT DONE PROPERLY, IT MAY CAUSE DISTORTION CHASSIS ASSEMBLY CN9001 Box-Purselock HV LEAD [CY] CN9002 4-065-850-11 CN9102 F-Pin Plug [WY] Purse w/GND lead CN9102 Lock 1-829-088-11 CN9103 CLIP-ON FERRITE 1-500-386-11...
Page 14
KV-34DRC430/36DRC430 G2 WIRE ROUTING CAUTION POINT REAR VIEW Dress wire in “L” Shape. U-Bracket O.K. CONDITION N.G CONDITION SIDE VIEW SIDE VIEW Wire Holder N.G! p/n: 4-065-850-11 Wire can touch Wire Holder Rear Cover!! p/n: 4-065-850-11 G2 Wire MUST be routed correctly so that the wire does NOT touch Rear Cover (Causes “Buzzing”...
KV-34DRC430/36DRC430 G2 & FOCUS LEAD WIRE DRESSING [CH] /[WY] /[HV] CAUTION POINT [CH] CLP9003 HV-Lead Spacer See CRT dress CRT SOCKET diagram for CLP9001 details. Number CN9001 spacers vary by CN9109 model. CN9003 CN9004 Push Wire Down [CH] CLP9002 CN9002...
Page 16
KV-34DRC430/36DRC430 F-PIN CABLE WIRE DRESSING CAUTION: 1-829-088-11 MAKE SURE Ground Lead P-F Cable Terminal is attached to w/Gnd. Lead Terminal CN501 (not CN528)!! (NOT dressed with other connectors) P-Shield [UY] [BY] [MY] CN501 TERMINAL CN 503 AC Conn. Tuner [AY]...
Page 17
Ground wire ECG - P/N 1-900-808-30 - 30 WCRT 1-900-808-31 - 34W CRT CRT BRKT ECG WIRE DRESSING (KV-34DRC430 ONLY) (Earth Coating Ground) Caution Points: 1. Make sure braided ECG wire loop does not twist, and stays flat on CRT surface.
Page 18
NO SLACK ON WIRE! secure on CRT secure on CRT pierce! pierce! CRT BRACKET CRT WIRE DRESSING (KV-34DRC430 ONLY) DGC Clip (p/n: 4-102-284-01) 1-900-804-64 DGC Restraint Cable (w/ x4 loops around DGC) Cable Holder Rotation 4-084-918-01...
Page 19
KV-34DRC430/36DRC430 SPEAKER ASSEMBLY WIRE DRESSING NOTE: Keep speaker wires away from pocket in the beznet (gray area). The wires can get pinched when installing the rear cover (due to boss on the rear cover). CLAMP 4-857-472-01 w/ 4x16mm screw 7-685-663-71...
KV-34DRC430/36DRC430 SECTION 2: SET-UP ADJUSTMENTS The following adjustments should be made when a complete Perform the adjustments in order as follows: realignment is required or a new picture tube is installed. 1. Beam Landing 2. Convergence These adjustments should be performed with rated power supply 3.
KV-34DRC430/36DRC430 6. Switch over the raster signal to red and blue and confi rm the 4. Tilt the V.STAT magnet and adjust static convergence to open or condition. close the V.STAT magnet 7. When the position of the defl ection yoke is determined, tighten it with the defl...
KV-34DRC430/36DRC430 2-3.2. TLH PLATE ADJUSTMENT 2-3.4. DYNAMIC CONVERGENCE ADJUSTMENTS Preparation: • Input a cross hatch pattern signal. • Set dynamic convergence using the following service registers. Note • Adjust unbalanced horizontal convergence of red and blue dots by areas of change.
KV-34DRC430/36DRC430 1. Set to Service Mode and adjust as follows: 3. Change CXA2170-P2 item 2 RGBS to 2 to make green only. 1. Overfocus to adjust DQP phase. Adjust the data 2170P-2 (CXA2170-D4 item 8) to balance left and right vertical line width.
KV-34DRC430/36DRC430 2-6.2. VIDEO INPUT - SUB HUE/SUB COLOR 2-6.3. RF INPUT - SUB CONTRAST ADJUSTMENT ADJUSTMENT Preparation: Preparation: • Input a Color Bar signal to VIDEO 1 (75 IRE 75%). • Input a Color Bar signal to RF (75 IRE 75%).
KV-34DRC430/36DRC430 2-6.4. RF INPUT - SUB HUE/SUB COLOR 2-7. WHITE BALANCE (CRT) AND SUB ADJUSTMENT BRIGHT ADJUSTMENT Preparation: Preparation • Input a Color Bar signal to RF (75 IRE 75%). • Input an all white 480I (15.734 KHz) signal into the VIDEO 1 input terminal to perform the White Balance (highlight, cut-off) adjustments.
KV-34DRC430/36DRC430 2-8. H RASTER CENTER ADJUSTMENT 2-9. PICTURE DISTORTION ADJUSTMENTS Preparation: • Input a monoscope signal. 2-9.1. NTSC (DRC) FULL MODE • Set to NTSC (DRC) mode. ADJUSTMENT 1. Face the picture tube in an east-west direction. (For best condition.) 1.
KV-34DRC430/36DRC430 CXA2170D-2 2-9.2. 1080I HD MODE ADJUSTMENT Item 1. HPOS (H-POSITION) 1. Input a 1080i cross-hatch signal and an HD monoscope full signal that contains overscan markers. (From service mode, verify 1080I mode). 2. If this procedure was not performed for full mode, adjust the raster position per Section 2-8.
KV-34DRC430/36DRC430 SECTION 3: SAFETY RELATED ADJUSTMENTS 3-1. PREPARATION BEFORE CONFIRMATION 3-5. PREPARATION FOR HV AND IK PROTECTOR CHECK Standard ................135.3 ± 1 VAC Check Condition: AC input voltage: 120 (± 2) VAC 1. Remove DZ board screws and carefully lift board as necessary to gain access to the bottom of the board.
KV-34DRC430/36DRC430 3-6-2. HIGH LIGHT CONDITION Input Video Signal:............All White Signal Picture level:..........Picture/Brightness Adjustment 1. Short across C8002, C8021, C8052, C8012, and C8015. 2. Set ABL current to 2.76 mA by adjusting picture and brightness towards max condition. 3. Adjust HV to obtain 34.5 ± 0.15 kV by precision RV1 jig.
KV-34DRC430/36DRC430 3-10. HV SERVICE FLOWCHART Start Is DZ Board Is the spare part on P. 32 changed? Which category part on P. 32 changed? Category B Category C Category D Category E Category A Confirm: Confirm: Confirm: Confirm: Confirm: Confirm:...
KV-34DRC430/36DRC430 SECTION 4: CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER Use the Remote Commander (RM-Y197) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator 4-1. SETTING SERVICE ADJUSTMENT MODE 4-1.3.
KV-34DRC430/36DRC430 4-2. MEMORY WRITE CONFIRMATION METHOD 1. After adjustment, pull out the plug from the AC outlet, then replace the plug in the AC outlet again. 2. Turn the power switch ON and set to Service Mode. 3. Call the adjusted items again to confi rm they were adjusted.
KV-34DRC430/36DRC430 4-4. SERVICE DATA Category Item Range *NOT be memorized VERSION VER* DMY1* 0-255 3D-COMB NRMD* Note: Item * uses the fixed setting in CLKS normal TV operations. NSDS* {Its setting can be changed for MSS* testing in Servcie mode only.
Page 37
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized V5/V6 2103-1 Others HDMI CBO2 0-63 CRO2 0-63 Single BLK=0 BLK=1 BLK=2 BLK=3 Notes: Settings applied to CXA2103 (M&S), if applied. ATPD Settings also based on 2170P-4/BLK data DCTR 2170P-1 Memory Comp /...
Page 38
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized Memory Comp / 2170P-1 HDMI Stick CV/YC 480i DCOL 2170P-2 Blanking On Blanking Off Power Off PICO* RGBS* BLKB RGBL YLMT Aging On Aging Off AGNG* AKBO* Other CLPP CLPG CLPS PPAD SYNP...
Page 39
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized 2170P-3 V5/V6 HDMI Memory Stick CV/YC Menu Twin Slide Show / 480i 480p 1080i 720p 480i 480p 1080i 720p Still Picture Index LTLV LTMD Vivid CTLV UBOF UCOF UHOF MIDE 0-63 SYSM VMLV*...
Page 40
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized 2170P-3 V5/V6 HDMI Memory Stick CV/YC Menu Twin Slide Show / 480i 480p 1080i 720p 480i 480p 1080i 720p Still Picture Index SYSM VMLV* 0-15 VMCR VMLM VMF0 VMDL 0-15 SHOF Movie SHF0...
Page 41
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized 2170P-3 Vivid Standard Movie 0-15 0-15 0-15 HDMI VGAP 0-15 VGAS 0-15 VGAB 0-15 VGAC 0-15 VGAV 0-15 Memory 2170P-4 Other Stick YCON Memory Note: VDO (V5&6) VDO (HDMI) Stick PT = Pass...
Page 42
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized Memory 2170P-4 Other Stick 0-15 0-15 0-15 0-15 V5/V6 HDMI Memory Stick CV/YC Menu Twin Slide Show/ 480i 480p 1080i 720p 480i 480p 1080i 720p Still Picture Index Vivid Standard GAMM Movie GAMM=0...
Page 43
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized Single MemoryStick 2170P-4 Others Others 1080Vcomp ABLT 0-15 SPOF 0-31 BLK=0 BLK=1 BLK=2 BLK=3 Note: DPSQ Settings based on BLK data LRGB 0-15 2170D-1 VPOS 0-63 VSIZ 0-63 1080Full Others Note: VSZO 0-63...
Page 56
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized Category Item Range *NOT be memorized SNNR MODE 3DNR WHCT 0-63 NIQM SNNR CLPW 0-63 CLPP 0-255 WSLT- A WSLT- B WSLT- C WSLT- D WSLT- E WSLT- F WSLT- G YHBW 0-255...
Page 57
KV-34DRC430/36DRC430 Category Item Range *NOT be memorized 3DNR Vivid Standard Movie 480i Others 480i Others 480i Others 480i Others 0-15 Vivid Standard Movie 480i Others 480i Others 480i Others 480i Others 0-31 Vivid Standard Movie 480i Others 480i Others 480i...
KV-34DRC430/36DRC430 SECTION 5: DIAGRAMS 5-1. CIRCUIT BOARDS LOCATION The components identifi ed by shading and symbol are critical for safety. Replace CH Board only with part number specifi ed. WY Board The symbol indicates a fast operating fuse and is displayed on the component side of the board.
KV-34DRC430/36DRC430 5-3. BLOCK DIAGRAMS BLOCK DIAGRAMS (1 OF 3) HS Signal Flow Video7 Video2 RGBYsYm Main Micro M306V7 HDMI CV/YC CV/YC EEPROM M24C32 Moni ExtRGB DRC-MF uPD64083 CV/YC RGBYsYm YCbCr CXD2095 Main C.Dec YCbCr CXA2103AQ DRCSW [SW0] NJM2283 CXA2170 ExtYCbCr...
Page 61
KV-34DRC430/36DRC430 BLOCK DIAGRAMS (2 OF 3) Deflection & HV System Block CXA2170Q STV9379 V DEF VDRV+/VDRV- DY-v Vout V PROT block Horizontal deflection EW DRV EW_DRV Chopper H CENT LA6500 HC_PARA H DEF Horizontal DY-h H Center H DRV/HPROT/HP IN...
Page 62
KV-34DRC430/36DRC430 BLOCK DIAGRAMS (3 OF 3) KV-34DRC430/36DRC430...
KV-34DRC430/36DRC430 UY BOARD SCHEMATIC DIAGRAM UY BOARD WAVEFORMS TO MY CN2305 CN1503 :B TO B — HDMI_R 2.2 Vp-p (H) 1.7 Vp-p (H) HDMI_L VIDEO J1509 V5 Y L1502 C1540 R1655 R1656 R1632 — :LB2016 1/16W 1/16W :RN-CP :RN-CP 1/16W...
KV-34DRC430/36DRC430 AY BOARD SCHEMATIC DIAGRAM (1 OF 2) AY BOARD WAVEFORM TO BY CN513 CN525 CN523 TO BY TO MY CN2302 TO MY CN3203 CN2002 — CN510 BIIC MS5V MS5V STBY5V 1.9 Vp-p (H) TO BY CN2804 3.3V 5V-D +BOVP...
KV-34DRC430/36DRC430 MY BOARD SCHEMATIC DIAGRAM (1 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
KV-34DRC430/36DRC430 MY BOARD SCHEMATIC DIAGRAM (2 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
KV-34DRC430/36DRC430 MY BOARD SCHEMATIC DIAGRAM (3 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
KV-34DRC430/36DRC430 MY BOARD SCHEMATIC DIAGRAM (4 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
Page 86
KV-34DRC430/36DRC430 [VIDEO PROCESSOR, 3D-COMB, MICRO (MAIN, CCD), AUDIO PROCESSOR] COMPONENT SIDE CN 2304 TO P X2001 3D CO M B C2041 C2042 C2050 C2043 C2046 C2240 L2203 C2059 C2238 R2247 Q 2215 C2227 L2205 C2060 Q 2211 C2061 M AI N V/ Y...
Page 87
KV-34DRC430/36DRC430 [VIDEO PROCESSOR, 3D-COMB, MICRO (MAIN, CCD), AUDIO PROCESSOR] CONDUCTOR SIDE TO P CN 2304 M A I N CRO M A R2133 R2136 X2001 3D CO M B R2139 R2145 R2134 R2144 C2038 Q 2206 R2052 C2240 C2238 R2242...
KV-34DRC430/36DRC430 BY BOARD SCHEMATIC DIAGRAM (1 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
KV-34DRC430/36DRC430 Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. BY BOARD SCHEMATIC DIAGRAM (2 OF 4) Data is provided for reference only.
KV-34DRC430/36DRC430 Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. BY BOARD SCHEMATIC DIAGRAM (3 OF 4) Data is provided for reference only.
KV-34DRC430/36DRC430 BY BOARD SCHEMATIC DIAGRAM (4 OF 4) Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only.
KV-34DRC430/36DRC430 P BOARD SCHEMATIC DIAGRAM Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. Data is provided for reference only. The P and PA Boards are interchangeable.
KV-34DRC430/36DRC430 Due to the complexity of this board, performing component level fi eld repairs is not recommended. If service is required, complete board replacement is the preferred repair method. PA BOARD SCHEMATIC DIAGRAM Data is provided for reference only. The P and PA Boards are interchangeable.
KV-34DRC430/36DRC430 5-5. SEMICONDUCTORS (1 OF 2) TOP VIEW 22pin TOP VIEW TOP VIEW TOP VIEW 5pin CXA2026AS 14pin 16pin 32pin M52055FP PST9120NL CXD2085M-T4 BH3868AFS-E2 TLC2932IPW PST9145NL SN74LV4053ANSR TLC2933IPWR-12 TC7SET08FU(TE85L) INDEX TOP VIEW TOP VIEW 240pin 32pin 64pin 48pin TOP VIEW...
A-1101-770-A DZ BOARD, COMPLETE 8-598-593-70 TUNER, FSS BTF-WA421 7-685-648-79 SCREW +BVTP 3X12 TYPE2 TT(B) (KV-34DRC430/36DRC430 L. SOUTH) 1-500-586-11 FILTER, CLAMP (FERRITE CORE) The high-voltage leads associated with the FBT on 1-769-837-11 CORD, POWER(WITH NOISE FILTER) this DZ Board are not included and must be ordered (KV-34DRC430/36DRC430 L.
Page 100
SHORT CHIP R501 1-216-864-11 SHORT CHIP JR512 1-216-864-11 SHORT CHIP R502 1-244-207-11 WIREWOUND 3.3K JR513 1-216-864-11 SHORT CHIP (KV-34DRC430/36DRC430 L. SOUTH) JR514 1-216-864-11 SHORT CHIP R503 1-205-997-11 CEMENT 2.2K JR515 1-216-864-11 SHORT CHIP (KV-36DRC430 L. SOUTH) JR516 1-216-864-11 SHORT CHIP...
Page 101
KV-34DRC430/36DRC430 NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R524 1-216-833-11 METAL CHIP 1/10W R596 1-216-833-11 METAL CHIP...
Page 109
KV-34DRC430/36DRC430 NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES JR5065 1-216-864-11 SHORT CHIP JR5501 1-216-864-11 SHORT CHIP...
Page 110
KV-34DRC430/36DRC430 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES IC LINK Q5507 8-729-052-29 TRANSISTOR 2SK2876-01MR-F122 Q5510 8-729-120-28 TRANSISTOR 2SC1623-L5L6 PS6505 1-576-288-42 IC LINK Q5512 8-729-120-28 TRANSISTOR 2SC1623-L5L6 PS6506 1-576-288-42 IC LINK Q5513 8-729-120-28 TRANSISTOR 2SC1623-L5L6 PS6550...
Page 111
1/10W R5015 1-216-841-11 METAL CHIP 1/10W R5074 1-260-328-11 METAL CHIP 1/2W R5016 1-208-832-11 METAL CHIP 120K 0.50% 1/10W (KV-34DRC430/36DRC430 L. SOUTH) R5079 1-218-720-11 METAL CHIP 0.50% 1/10W R5017 1-208-832-11 METAL CHIP 120K 0.50% 1/10W R5018 1-216-833-11 METAL CHIP 1/10W R5080...
Page 112
KV-34DRC430/36DRC430 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R5128 1-216-828-11 METAL CHIP 3.9K 1/10W R5519 1-218-740-11 METAL CHIP 100K 0.50% 1/10W R5129 1-216-809-11 METAL CHIP 1/10W R5520 1-216-833-11 METAL CHIP 1/10W R5130 1-216-797-11 METAL CHIP...
Page 113
METAL CHIP 0.50% 1/10W R6548 1-216-823-11 METAL CHIP 1.5K 1/10W R5594 1-216-833-11 METAL CHIP 1/10W R6556 1-243-979-71 METAL OXIDE (KV-34DRC430/36DRC430 L. SOUTH) R6557 1-243-979-71 METAL OXIDE R5597 1-218-750-11 METAL CHIP 270K 0.50% 1/10W ! R6590 1-249-415-11 CARBON 1/4W R5603 1-216-857-11...
Page 114
KV-34DRC430/36DRC430 NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R8032 1-216-844-11 METAL CHIP 1/10W R8098 1-249-441-11 CARBON...
Page 115
KV-34DRC430/36DRC430 NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES RELAY C2050 1-164-156-11 CERAMIC CHIP 0.1µF C2058 1-126-963-11 ELECT 4.7µF...
Page 119
KV-34DRC430/36DRC430 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES Q2313 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R2079 1-216-864-11 SHORT CHIP Q2314 8-729-600-22 TRANSISTOR 2SA1235-F R2081 1-216-809-11 METAL CHIP 1/10W Q2315 8-729-600-22 TRANSISTOR 2SA1235-F R2082 1-216-809-11 METAL CHIP 1/10W Q2316...
Page 120
KV-34DRC430/36DRC430 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R2209 1-216-821-11 METAL CHIP 1/10W R2253 1-216-809-11 METAL CHIP 1/10W R2210 1-216-818-11 METAL CHIP 1/10W R2254 1-216-817-11 METAL CHIP 1/10W R2211 1-216-821-11 METAL CHIP 1/10W R2255 1-216-817-11...
Page 121
KV-34DRC430/36DRC430 REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R2344 1-216-833-11 METAL CHIP 1/10W R2459 1-216-821-11 METAL CHIP 1/10W R2345 1-216-809-11 METAL CHIP 1/10W R2460 1-216-809-11 METAL CHIP 1/10W R2346 1-218-734-11 METAL CHIP 0.50% 1/10W R2464...
Page 122
KV-34DRC430/36DRC430 MY UY REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R2529 1-216-809-11 METAL CHIP 1/10W R2576 1-216-821-11 METAL CHIP 1/10W R2530 1-216-809-11 METAL CHIP 1/10W R2577 1-216-837-11 METAL CHIP 1/10W R2531 1-216-821-11 METAL CHIP 1/10W...
Page 140
KV-34DRC430/36DRC430 NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES C9022 1-101-004-00 CERAMIC 0.01µF COIL C9023 1-101-004-00 CERAMIC 0.01µF...
Page 141
KV-34DRC430/36DRC430 CH HAX WY NOTE: The components identifi ed by shading mark are critical for safety. Replace only with part number specifi ed. REF. NO. PART NO. DESCRIPTION VALUES REF. NO. PART NO. DESCRIPTION VALUES R9048 1-216-049-11 RES-CHIP 1/10W R1007...
Page 144
In an effort to reduce the size of this pdf file the tiled schematics are not attached to this Service Manual. To receive a complete set of the tiled schematics for this manual please submit a request to the Service Promotion Department at Service_Promotion@am.sony.com.
Need help?
Do you have a question about the TRINITRON KV-34DRC430 and is the answer not in the manual?
Questions and answers