hit counter script
Sony DSC-F505 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Digital Camera
  5. Cyber-shot DSC-F505
  6. Service manual

Sony DSC-F505 Service Manual

Digital still camera
Hide thumbs Also See for DSC-F505:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
SERVICE MANUAL
Ver 1.2 2000. 03
Level 2
With SUPPLEMENT-1
(9-974-192-81)
This service manual contains information for Japanese model as well.
On the PS-427, SY-56 board
This service manual provides the information that is premised the circuit
board replacement service and not intended repair inside the PS-427,
SY-56 board.
Therefore, schematic diagram, printed wiring board and electrical parts
list of the PS-427, SY-56 board are not shown.
The following pages are not shown.
System
Recording format
Digital (JPEG based)/Field
recording
Video signal
NTSC color, EIA standards
PAL color CCIR standards
Image device
1/2-inch CCD (total number
of square pixels : 1636 x 1236),
square grid, primary color filter
Interface format
Lens
ƒ = 7.1 - 35.5 mm (38 - 190 mm, when
converted into a 35 mm still camera)
0.5 m - ∞ ("W" side)
0.08 m - ∞ (Macro, "W" side)
F = 2.8 - 3.3
Photometric system
TTL system
Exposure control
Automatic exposure
White balance
Automatic, Indoor, Outdoor,
One-push
Data compression system
Movie : MPEG-1
Still : JPEG
Audio (with still image) :
MPEG AUDIO (Monaural)
Data format
Still : 1600 x 1200
1024 x 768
640 x 480
320 x 240 (E-mail)
Movie : 320 x 240, 160 x 112
MICROFILM
SPECIFICATIONS
Memory
"Memory stick"
Flash
Recording distance
7
1
limitations : 11
/
inches to 8
/
feet
8
3
(0.3 m to 2.5 m), automatic flash
control system
Shutter speed
NTSC : 1/8 - 1/725
PAL : 1/6 - 1/600
LCD screen
Screen size
2 inches
LCD panel
TFT
Total dot number
122,980 (559 x 220) dots
Input and output connectors
A/V out (Monaural)
Minijack
Video : 1Vp-p, 75 ohms,
unbalanced, sync negative
Audio : monaural, 327 mV
(at output, impedance more than
47 kilohms)
Output impedance with less than
2.2 kilohms
Digital I/O (serial)
Minijack
RS-232C based, 9.6 Kbps to
115.2 Kbps
Digital I/O (USB)
Special minijack
USB 1.0 based
– 1 –
DSC-F505
Hong Kong Model
PS-427 board
Schematic diagram ............................... Pages 4-15 to 4-18
Printed wiring board .............................. Page
Electrical parts list ................................. Pages 6-12 to 6-13
SY-56 board
Schematic diagram ............................... Pages 4-23 to 4-33
Printed wiring board .............................. Pages 4-19 to 4-22
Electrical parts list ................................. Pages 6-13 to 6-14
General
Power consumption
Using the AC power
adaptor/charger :
Recording : 3.6 W
Playback : 3.1 W
Using the rechargeable
NP-FS11 lithium ion battery :
Recording : 3.3 W
Playback : 2.7 W
Operation temperature
32°F to 104°F (0°C to 40°C)
Storage temperature
-4°F to 140°F (-20°C to 60°C)
Dimensions
1
1
3
Approx. 4
/
x 2
/
x 5
/
in.
4
2
8
(107.2 x 62.2 135.9 mm)
(w / h / d)
Mass
Approx. 15 oz (435 g)
(excluding batteries)
Approx. 1 lb (475 g)
(including battery,
"Memory stick" (4 MB),
wrist strap and lens cap etc.)
AC-VF10 AC power adaptor/
charger
Power requirements
100 to 240 V AC, 50/60 Hz
Power consumption
13 W
DIGITAL STILL CAMERA
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Korea Model
Tourist Model
4-11
Output voltage
DC OUT : 4.2 V, 1.8 A in operating
mode
Battery charge terminal :
4.2 V, 1.5 A in charge mode
Operation temperature
32°F to 104°F (0°C to 40°C)
Storage temperature
-4°F to 140°F (-20°C to 60°C)
15
9
3
Approx. 1
/
x 1
/
x 3
/
in.
16
16
8
(49 x 39 x 85 mm) (w / h / d)
Mass
Approx. 4.2 oz. (120 g)
(excluding batteries)
NP-FS11 battery pack
Voltage
DC 3.6 V
Capacity
4.1 Wh
Type
Lithium ion type
Design and specifications are subject
to change without notice.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DSC-F505 and is the answer not in the manual?

Questions and answers

Related Manuals for Sony DSC-F505

Summary of Contents for Sony DSC-F505

  • Page 1 DSC-F505 SERVICE MANUAL US Model Canadian Model Ver 1.2 2000. 03 Level 2 AEP Model With SUPPLEMENT-1 UK Model (9-974-192-81) E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model This service manual contains information for Japanese model as well.
  • Page 2 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS GENERAL PRINTED WIRING BOARDS AND ..............1-1 Parts identification ..............1-1 SCHEMATIC DIAGRAMS Preparation ................. 1-2 4-1. Frame Schematic Diagram (1) ........4-3 1 Charging the battery pack and Frame Schematic Diagram (2) ........4-5 “Memory Stick” ............1-2 4-2.
  • Page 4 ADJUSTMENTS 1-5. LCD SYSTEM ADJUSTMENT ........5-35 LCD Initial Data Input ..........5-35 Before starting adjustment ..........5-1 VCO Adjustment (Control Switch Block (FK) ) ... 5-36 1-1. Adjusting items when replacing main parts and boards .. 5-2 D Range Adjustment (Control Switch Block (FK) ) ..5-36 5-1.

  • Page 5: Service Note

    The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-F505 is simply turned off. Therefore, the remaining voltage must be discharged as described below.
  • Page 6 [Description on Self-diagnosis Display] Self-diagnosis display • C: ππ: ππ You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ππ: ππ...

  • Page 7: General

    DSC-F505 SECTION 1 This section is extracted from GENERAL instruction manual.
  • Page 16 1-10...
  • Page 17 1-11...
  • Page 18 1-12...
  • Page 19 1-13...
  • Page 20 1-14...
  • Page 21 1-15E...

  • Page 22: Disassembly

    DSF-F505 SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. START 2-1. REAR CABINET BLOCK 2-2. ZOOM LENS BLOCK 2-5. LCD PANEL BLOCK 2-6. HI-70 AND DD-131 BOARDS 2-3. CABINET (LT) BLOCK CONTROL SWITCH BLOCK (FK) BATTERY HOLDER BLOCK 2-7.

  • Page 23: Removal Of Rear Cabinet Block

    NOTE : Follow the disassembly procedure in the numerical order given. 2-1. REMOVAL OF REAR CABINET BLOCK 2 Two screws 4 FP-134 flexible board (M1.7) (HI-70 board, CN901) 5 Flexible board (Control switch block (FK)) (HI-70 board, CN607) 1 Two screws (M1.7) Front cabinet assembly 3 Rear cabinet assembly...

  • Page 24: Removal Of Cabinet (Lt) Block

    REMOVAL OF CABINET (LT) BLOCK 2-4. REMOVAL OF LENS BLOCK 2 Screw (M1.7) 3 Cabinet (LT) block 5 Harness (SM-114) (Flash unit (ST), 2P) 8 Screw (M1.7) (Note) Flash unit 7 Two screws (Note) 2 CN453 (M1.7) (SY-56 board) 1 Push the Release knob 4 FP-136 flexible board (SY-56 board, CN454) 0 Lens block...

  • Page 25: Removal Of Lcd Panel Block And Control Switch Block (Fk)

    2-5. REMOVAL OF LCD PANEL BLOCK AND CONTROL SWITCH BLOCK (FK) Rear cabinet assembly 8 Control switch block (FK) Button (LCD bright) 2 Zoom switch (RV001) 1 Screw (1.7 x 4) 6 Screw (M1.7) Knob (LCD back light) 3 Two screws (1.7 x 4) 7 Two screws (M1.7) 4 Two screws (1.7)

  • Page 26: Removal Of Hi-70, Dd-131 Boards And Battery Holder Block

    2-6. REMOVAL OF HI-70, DD-131 BOARDS AND BATTERY HOLDER BLOCK 8 Screw (M1.7) 5 Three screws (1.7 x 4) 0 Battery holder block 3 Harness (Microphone) 6 HI-70 board (HI-70 board, CN701) 4 Control switch block (PW) (HI-70 board, CN604) BB fixed sheet 9 Screw (M1.7)

  • Page 27: Service Positionn-3 (Hi-70 And Dd-131 Boards)

    • SERVICE POSITION-3 (HI-70 and DD-131 BOARDS) HI-70 board Control switch block (PW) Rear cabinet block CN602 CN603 Front cabinet block DD-131 board CN702 Harness (HB-50) Harness (SP-163) FP-133 flexible board CN605 (Not used) CN456 (SY-56 board) CN455 (SY-56 board) Battery holder block (To AC power adaptor) Zoom lens block...

  • Page 28: Removal And Attaciment Of Fp-133 Flexible Board

    2-9. REMOVAL AND ATTACHIMENT OF FP-133 FLEXIBLE BOARD NOTE : For folding new FP-133 flexible board, refer to “2-10. To fold the new FP-133 flexible board” . FP-133 flexible board When attaching, coil in the direction of (33P side) arrow A with two and a half revolutions. FP-133 flexible board (FP-133 flexible board ) Screw (M1.7)

  • Page 29: Removal Of Crystal Indication Module

    2-11. REMOVAL OF CRYSTAL INDICATION MODULE Note for installation 1 Crystal indication module (LCD901) (FP-134 flexible board, 24P) Portion B BL cushion Portion A Portion C and D 5 Cold cathode fluorescent tube (ND901) (Inverter transformer unit) 3 FP-134 flexible board 4 Screw (M1.7) BL light interception sheet 6 Inverter transformer unit...

  • Page 30: Circuit Boards Location

    2-13. CIRCUIT BOARDS LOCATION CD-236 HI-70 (CCD imager, Camera) (LCD drive, Timing generator, Video, Audio, HI control) LD-98 (Lens drive) Flash unit (MC) Flash unit (ST) PS-427 (Camera DSP, Memory control) SY-56 (SH DSP, Memory, Serial I / O, Connector, Digital I / O, ) Inverter transformer unit DD-131 (DC / DC Converter)

  • Page 31: Block Diagrams

    Ver 1.1 1999.10 DSC-F505 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM CD-236 BOARD PS-427 BOARD SY-56 BOARD LENS IRIS METER IC101 IC103 IC251 DATA BUS CCD OUT DATA BUS IO CCD IMAGER A/D CONV. CAMERA DSP (SEE PAGE 4-9)

  • Page 32: Printed Wiring Boards And Schematic Diagrams

    Ver 1.1 1999.10 DSC-F505 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...

  • Page 33: Frame Schematic Diagram (1)

    DSC-F505 Ver 1.1 1999.10 4-1. FRAME SCHEMATIC DIAGRAM (1) CONTROL SWITCH BLOCK(CF) CN002 10P CN453 REG_GND -MOUNT FLEXIBLE- KEY_AD4 S001 DC_300V D_3.2V MACRO MF UNIT S005 REG_GND S004 FLASH UNIT S002 FOCUS PHOTOTR_5V (W/B SET) (CARD EDGE) D_3.2V AUTO S003...

  • Page 34: Frame Schematic Diagram (2)

    Ver 1.1 1999.10 DSC-F505 FRAME SCHEMATIC DIAGRAM (2) FLASH UNIT(MC) BT901 CN001 DD-131 CN604 CN002 BATT UNREG BATTERY REG_GND ST_GND ST_GND CONTROL SWITCH BLOCK(PW) BATT SIG TERMINAL BOARD REG_GND ST UNREG ST UNREG BOARD BATT GND -MOUNT FLEXIBLE- STB_CHARGE STB_CHARGE...

  • Page 35: Printed Wiring Boards And Schematic Diagram

    DSC-F505 Ver 1.1 1999.10 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM CD-236 BOARD (SIDE A) CD-236 BOARD (SIDE B) C131 C130 C127 R118 C133 R117 L103 R109 R116 R123 C120 Q103 R115 R122 C117 IC103 R114 C116 R121 FB103 X101...
  • Page 36 Ver 1.1 1999.10 DSC-F505 CD-236 BOARD FB107 CCD IMAGER,CAMERA NO MARK : STILL/PB mode -REF.NO.:3000 SERIES- FB108 : STILL mode XX MARK : NO MOUNT : PB mode R124 1608 L102 R104 FB101 10uH C128 C132 C123 0.1u C140 0.1u C139 P0/S2.7...

  • Page 37: Lens Drive

    DSC-F505 Ver 1.1 1999.10 LD-98 BOARD (SIDE A) C412 IC402 R417 C403 C402 L402 L403 IC403 IC406 CN402 LD-98 BOARD (SIDE B) C426 R426 C417 C413 C419 R416 R432 R410 C421 R412 C408 C410 C424 C423 IC404 R415 IC407 L404...
  • Page 38 Ver 1.1 1999.10 DSC-F505 LD-98 BOARD C402 1608 R405 LENS DRIVE 4700 ±0.5% R404 R403 NO MARK : STILL/PB mode -REF.NO.:4000 SERIES- : STILL mode R436 R409 R411 2200 XX MARK : NO MOUNT Q402 120k : PB mode R402 ±0.5%...

  • Page 39: Mf Unit

    Ver 1.1 1999.10 DSC-F505 CONTROL SWITCH R001 LF001 R002 BLOCK(PW) 3300 CN002 2200 DIGITAL • CONTROL SWITCH BLOCK(PW) is replaced as a block. (USB) So that this PRINTED WIRING BOARD is omitted. LF002 D002 D003 01ZA8.2 01ZA8.2(TPL3) (TPL3) DIGITAL J001...
  • Page 40 DSC-F505 Ver 1.1 1999.10 HI-70 BOARD (SIDE A) CN702 CN605 R663 R606 D602 C621 R681 C306 R622 R661 R607 C301 R611 C606 C607 R313 C620 R312 Q603 R662 Q302 R610 R612 Q608 Q610 Q607 C302 R304 C605 R635 R644 X602...
  • Page 41 Ver 1.1 1999.10 DSC-F505 HI-70 BOARD (SIDE B) Q611 Q612 R605 IC607 LND001 R667 C609 R604 D606 LND002 CN606 R621 R620 D608 R619 R618 R738 R726 C814 C812 C629 R727 R742 FB605 C813 R932 R933 R934 R935 CN701 CN604 C920...

  • Page 42: Lcd Drive

    DSC-F505 Ver 1.1 1999.10 HI-70 BOARD(1/6) LCD DRIVE (RGB BLOCK) -REF.NO.: 2000 SERIES- XX MARK : NO MOUNT NO MARK : STILL/PB mode R806 TO (5/6) PANEL_6.5V C815 R804 R827 R823 L802 10uH R822 R805 P_4.9V TO (2/6) R828 L801...

  • Page 43: Timing Generator

    Ver 1.1 1999.10 DSC-F505 HI-70 BOARD(2/6) TIMING GENEREATOR (TG BLOCK) -REF.NO.: 2000 SERIES- XX MARK : NO MOUNT IC902 COM AMP NO MARK : STILL/PB mode L901 10uH TO(5/6) PANEL_13.2V R941 L902 R934 TO(5/6) PANEL_-15.3V 10uH ±0.5% IC902 R933 13.4...

  • Page 44: Video

    DSC-F505 Ver 1.1 1999.10 HI-70 BOARD(3/6) VIDEO(VI BLOCK) NO MARK : STILL/PB mode -REF.NO.:2000 SERIES- : STILL mode SIGNAL PATH • XX MARK : NO MOUNT : PB mode VIDEO SIGNAL R313 CHROMA Y/CHROMA TO (5/6) A_3.2V L301 47uH TO (5/6) A_4.9V...

  • Page 45: Audio

    Ver 1.1 1999.10 DSC-F505 R717 Q705 HI-70 BOARD(4/6) 2SA1586YG-TE85L REF 3.2V REG AUDIO (AU BLOCK) BEEP -REF.NO.: 2000 SERIES- XX MARK : NO MOUNT C735 TO(5/6) NO MARK : STILL/PB mode 6.3V S : STILL mode AU_SPON P : PB mode...

  • Page 46: Hi Control (1/2

    DSC-F505 Ver 1.1 1999.10 HI-70 BOARD(5/6) CN607 REG_GND Note : Note : REG_GND ZOOM_SW_AD CONNECTOR (HI BLOCK(1/2)) ZOOM_SW_AD SYS_V The components identified by Les composants identifiés par une SYS_V D.32V -REF.NO.: 2000 SERIES- D_3.2V mark ! or dotted line with mark...

  • Page 47: Hi Control (2/2

    Ver 1.1 1999.10 DSC-F505 HI-70 BOARD(6/6) HICONTROL (HI-BLOCK(2/2)) -REF.NO.: 2000 SERIES- XX MARK : NO MOUNT NO MARK : STILL/PB mode S : STILL mode P : PB mode TO (5/6) HI_UNREG R675 C630 IC605 IC606 S-80820ANNP-EDH-T2 +3.1V REG D_3.2V N.C.
  • Page 48 DSC-F505 Ver 1.1 1999.10 DD-131 BOARD (SIDE A) D001 D007 R071 C032 R072 L003 T002 T003 CN002 C027 C026 Q012 C024 C040 R057 Q005 R062 L001 C017 C034 Q010 CN001 PS001 C029 L005 R056 R058 PS003 C020 C045 C035 C016...
  • Page 49 Ver 1.1 1999.10 DSC-F505 DD-131 BOARD DC/DC CONVERTER(DD BLOCK) -REF.NO.:2000 SERIES- XX MARK : NO MOUNT NO MARK : STILL PB mode : STILL mode : PB mode 838AN-1319 T003 Q011 C037 R036 DC/DC CONVERTER <V-> CPH3206-TL 2.2u ±0.5% SWITCHING...
  • Page 50 DSC-F505 Ver 1.1 1999.10 CONTROL SWITCH BLOCK(FK) R9011 RV001 R9012 D009 LND002 CONTROL SWITCH BLOCK(FK) is (ZOOM) • replaced as a block. STATIC_GND 1SS387-TPL3 So that this PRINTED WIRING BOARD is omitted. D006 (FLASH LAMP) TLYU1008(T05,SOY) CN002 R003 CN001 REG_GND...

  • Page 51: Waveforms

    Ver 1.1 1999.10 DSC-F505 4-3. WAVEFORMS HI-70 DD-131 CD-236 BOARD BOARD BOARD !¶ IC001 1 OUT7 IC101 !£,@º IC102 #∞ IC802 $¡ LCD IC902 7 IC301 1 A/V OUT 0.5µsec/div 50 µsec/div 50µsec/div 50µsec/div 0.2V/div 2 V/div 1V/div 0.5V/div 0.46Vp-p 6.5Vp-p...

  • Page 52: Printed Parts Location

    DSC-F505 Ver 1.1 1999.10 4-4. PRINTED PARTS LOCATION CD-236 BOARD LD-98 BOARD HI-70 BOARD HI-70 BOARD DD-131 BOARD (SIDE A) (SIDE B) C101 R116 C401 R430 C001 C-11 L006 R034 D-11 C102 R117 C402 R431 C002 C-11 L007 R035 D-10...

  • Page 53: Adjustments

    DSC-F505 SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

  • Page 54: Adjusting Items When Replacing Main Parts And Boards

    1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by r in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment Adjustment Section Initialization of B, D, Initialization of D page data E, F page data Initialization of B, E, F, 7 page data...

  • Page 55: Adjustments

    5-1. ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...

  • Page 56: Preparations

    1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. Pattern box DISASSEMBLY”. Note 2: When performing only the adjustments, the boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-5. 2) Connect the Adjustment remote commander to control switch block (FK) CN002 via CPC-9 jig (J-6082-393-C, Note3).
  • Page 57 Ver 1.1 1999.10 VIDEO Terminated at 75 Ω (Yellow) Vector scope Color monitor AUDIO Harness (SP-163) (White) Inverter transformer unit To HI-70 board, CN702 AV out J001 Control switch block (FK) CN002 Harness (HB-50) To HI-70 board, CN605 Memory stick CN607 CN901 CN603...

  • Page 58: Precaution

    1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments. WHITE BALANCE (Control switch block (CF) ) ..AUTO FLASH LEVEL (Menu display) ......NORMAL EXPOSURE (Menu display) ........... 0EV EFFECT (Menu display) ..........OFF DEMO MODE (Menu display) ........

  • Page 59: Preparing The Flash Adjustment Box

    4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; Provide woody board A, B and C of 15mm thickness. woody board A (2) woody board B (2) woody board C (1)

  • Page 60: Initialization Of B, D, E, F

    1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA 3. D Page Table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the D Page 1-2-1. INITIALIZATION OF D PAGE DATA Data”.) 1. Initializing the D Page Data Fixed data-2 : Modified data.
  • Page 61 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Bright adj. (LCD) Battery end adj. Color adj. (LCD) Fixed data-1 White balance adj. (LCD) (Initialized data) Contrast adj.
  • Page 62 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-2 (Initialized data) (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data) Table. 5-1-2. Fixed data-2 (Modified data, copy the data built in the same model.) Fixed data-1 (Initialized data)

  • Page 63: Initializing The B, E, F

    1-2-2. Initializing the B, E, F, 7 Page Data 3. F Page table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , 7 Page Data”.) 1. Initializing the B, E, F, 7 Page Data Fixed data-2 : Modified data.
  • Page 64 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Color reproduction adj. Mechanical shutter adj. (without ND filter) Fixed data-1 Auto white balance adj. (Initialized data) Fixed data-1 (Initialized data) Strobe white balance adj. Auto white balance ND filter compensation adj.
  • Page 65 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Table. 5-1-3. 5-13...
  • Page 66 4. E Page Table Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , Initial value Address 7 Page Data”.) NTSC PAL Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , Fixed data-1 7 Page Data”.) (Initialized data)
  • Page 67 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) 5-15...
  • Page 68 5. B Page Table Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , Initial value Address 7 Page Data”.) NTSC PAL Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , Fixed data-1 7 Page Data”.) (Initialized data)
  • Page 69 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) 5-17...
  • Page 70 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Table. 5-1-5. 5-18...

  • Page 71: Page Table

    6. 7 Page Table Remark Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , Initial value Address 7 Page Data”.) NTSC Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , Fixed data-1 7 Page Data”.) (Initialized data)
  • Page 72 Remark Remark Initial value Initial value Address Address NTSC PAL NTSC PAL CCD black defect compensation CCD white defect compensation Fixed data-1 (Initialized data) Table. 5-1-6. CCD white defect compensation 5-20...

  • Page 73: Video System Adjustments

    1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Adjustment (Control Switch Block (FK) ) 1. Video Sync Level Adjustment Adjust the burst level of the composite video signal output. (Control Switch Block (FK) ) Adjust the sync level of the composite video signal output. Mode PLAY Mode...

  • Page 74: Camera System Adjustments

    1-4. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Mode STILL Subject Arbitrary...

  • Page 75: Flange Back Adjustment (Using Minipattern Box)

    2. Flange Back Adjustment Adjusting method: (Using Minipattern Box) Install the minipattern box so that the distance between it and The inner focus lens flange back adjustment is carried out the front of the lens of the camera is less than 3cm. automatically.

  • Page 76: (Using Flange Back Adjustment Chart)

    3. Flange Back Adjustment 4. Flange Back Check (Using Flange Back Adjustment Chart) Mode STILL Subject Siemens star The inner focus lens flange back adjustment is carried out (2.0 m from the front of the lens) automatically. In whichever case, the focus will be deviated during (Luminance : approx.

  • Page 77: Picture Frame Setting

    5. Picture Frame Setting 6. F No. Standard Data Input Compensate the unevenness of the iris meter sensitivity. Mode STILL Mode STILL Subject Color bar chart (Color reproduction adjustment frame) Subject Clear chart (Approx. 90cm from the front of the lens) (Color reproduction adjustment frame) Measurement Point Video output terminal...

  • Page 78: Agc Standard Gain And Max Gain Adjustment

    8. AGC Standard Gain and Max Gain Adjustment 9. Light Level Adjustment and ND shutter check Adjust the AGC standard gain and max gain. Adjust the standard LV value. Mode STILL Mode STILL Subject Clear chart Subject Clear chart (Color bar standard picture frame) (Color bar standard picture frame) Adjustment Page Measurement Point...

  • Page 79: Auto White Balance Standard Data Input

    10. Auto White Balance Standard Data Input 11. Auto White Balance ND Filter Compensation Adjust the white balance standard data at 3200K. Adjustment Adjust to the proper auto white balance output data with Built-in Mode STILL ND filter. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor.

  • Page 80: Auto White Balance Adjustment

    12. Auto White Balance Adjustment Processing after Completing Adjustments: Adjust to the proper auto white balance output data. 1) Select page: 0, address: 03, and set data: 00. If it is not correct, auto white balance and color reproducibility will 2) Select page: B, address: 41, set data: 00, and press the PAUSE be poor.

  • Page 81: Color Reproduction Adjustment

    13. Color Reproduction Adjustment 13-2. Color Reproduction Adjustment (With ND Filter) Adjust the color Separation matrix coefficient so that proper color Mode STILL reproduction is produced. Subject Color bar chart (Color bar standard picture frame) 13-1. Color Reproduction Adjustment (Without ND Filter) Adjustment Page Mode STILL...

  • Page 82: Color Reproduction Check

    13-3. Color Reproduction Check Processing after Completing Adjustments: 1) Select page: E, address: 52, set the data noted down at step 2), Mode STILL and press the PAUSE button of the adjustment remote Subject Color bar chart commander. (Color reproduction adjustment frame) 2) Select page: B, address: 41, set data: 00, and press the PAUSE Measurement Point Video output terminal...

  • Page 83: White Balance Check

    14. White Balance Check 15. Strobe White Balance Adjustment Adjust the white balance when the strobe light flashes. Mode STILL Mode STILL Subject Clear chart (Color reproduction adjustment frame) Subject Flash adjustment box (Note5) (1.0m from the front of the lens) Filter Filter C14 for color temperature correction...

  • Page 84: Strobe Light Level And White Balance Check

    16. Strobe Light Level and White Balance Check 17. CCD Black Defect Compensation Check the light level regulation and the white balance when the Mode STILL strobe light flashes. Subject Clear chart Mode STILL (25 cm from the front of the lens) Subject Flash adjustment box (Note4) (Note1)

  • Page 85: Ccd Black Defect Compensation Check

    18. CCD Black Defect Compensation Check Processing after Completing Adjustments: Select page: F, address: DF, set the data noted down at step 5), Mode STILL and press the PAUSE button. Subject Clear chart Select page: 6, address: 01, and set data: 00, and press the (25 cm from the front of the lens) PAUSE button of the adjustment remote commander.

  • Page 86: Ccd White Defect Compensation

    19. CCD White Defect Compensation 20. CCD White Defect Compensation Check Mode STILL Mode STILL Subject Clear chart Subject Clear chart (25 cm from the front of the lens) (25 cm from the front of the lens) (Note1) (Note1) Measurement Point Display data of page: 6, address: 55 Measurement Point Display data of page: 6, address: 55...

  • Page 87: Lcd System Adjustment

    1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input Before perform the LCD system adjustments, check that the specified Mode PLAY values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Signal Arbitrary Note 1: The back light (fluorescent tube) is driven by a high voltage AC Adjustment Page power supply.

  • Page 88: Vco Adjustment (Control Switch Block (Fk) )

    2. VCO Adjustment (Control Switch Block (FK) ) 3. D Range Adjustment (Control Switch Block (FK) ) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the RGB decoder used to drive the LCD to the be blurred.

  • Page 89: Bright Adjustment (Control Switch Block (Fk) )

    4. Bright Adjustment (Control Switch Block (FK) ) 5. Contrast Adjustment (Control Switch Block (FK) ) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value.

  • Page 90: Color Adjustment (Control Switch Block (Fk) )

    6. Color Adjustment (Control Switch Block (FK) ) 7. V-COM Level Adjustment (Control Switch Block (FK) ) Set the color saturation to the standard value. If deviated, the color Set the common electrode drive signal level of LCD to the specified will be to dark or light.

  • Page 91: V-Com Adjustment

    8. V-COM Adjustment 9. White Balance Adjustment (HI-70 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode PLAY conspicuous vertical lines.

  • Page 92: System Control System Adjustment

    1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Battery End Adjustment (SY-56 board) Check the battery end voltage. Mode STILL Subject Arbitrary Measurement Point Display data of page: 2, address: 51 Measuring Instrument Adjustment remote commander Adjustment Page Adjustment Address 30 to 34, 4A Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig.

  • Page 93: Service Mode

    5-2. SERVICE MODE 2-1. ADJUSTMENT REMOTE COMMANDER The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory.

  • Page 94: Data Process

    2-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.

  • Page 95: Service Mode

    2-3. SERVICE MODE 2. Bit value discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table 1. Setting the Test Mode below to discriminate if the bit value is “1” or “0”. Page D Address 10 Display on the adjustment remote commander...

  • Page 96: Switch Check (1)

    3. Switch check (1) Page 2 Address 43 Function When bit value=1 When bit value=0 XPOWER SW (PW block) XCAM/PLAY SW STILL PLAY CAMERA (PW block) MOVIE SHUTTR SW (PW block) XSHUTTER LOCK SW (PW block) MEMORY STICK IN SW (HI-70 board) XSTILL/MOVIE SW MOVIE...

  • Page 97: Repair Parts List

    DSC-F505 SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they are The components identified by Les composants identifiés par une seldom required for routine service. Some delay mark ! or dotted line with mark marque ! sont critiques pour la should be anticipated when ordering these items.

  • Page 98: Front Cabinet Assembly

    6-1-2. FRONT CABINET ASSEMBLY not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied MIC901 not supplied not supplied not supplied not supplied not supplied supplied not supplied supplied not supplied not supplied (NOTE) NOTE : Refer to page 2-5 "2-7.

  • Page 99: Rear Cabinet Assembly

    6-1-3. REAR CABINET ASSEMBLY not supplied not supplied SP901 LCD901 ND901 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified.

  • Page 100: Lens Cabinet Assembly

    6-1-4. LENS CABINET ASSEMBLY not supplied not supplied not supplied not supplied not supplied not supplied not supplied Lens assembly (See page 6-5) not supplied not supplied not supplied not supplied The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety.

  • Page 101: Lens Assembly

    6-1-5. LENS ASSEMBLY not supplied not supplied not supplied IC101 M901 not supplied not supplied M902 not supplied Be sure to read “Note on the CCD Imager replacement” on page 4–10 when changing the CCD imager. Ref. No. Part No. Description Remark Ref.

  • Page 102: Electrical Parts List

    CD-236 6-2. ELECTRICAL PARTS LIST Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by In each case, u: µ , for example: may be different from the parts specified in the mark ! or dotted line with mark uA...: µ...
  • Page 103 CD-236 DD-131 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R110 1-218-933-11 RES,CHIP 1/16W C039 1-107-682-11 CERAMIC CHIP R111 1-218-937-11 RES,CHIP 1/16W C040 1-109-982-11 CERAMIC CHIP C041 1-107-682-11 CERAMIC CHIP R113 1-218-977-11 RES,CHIP 100K 1/16W C042 1-115-566-11 CERAMIC CHIP 4.7uF R114...
  • Page 104 DD-131 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC LINK > R028 1-218-972-11 RES,CHIP 1/16W R029 1-218-970-11 RES,CHIP 1/16W ! PS001 1-533-761-21 LINK, IC (SMD) 1.4A R030 1-208-711-11 METAL CHIP 0.50% 1/16W ! PS002 1-533-761-21 LINK, IC (SMD) 1.4A R031...
  • Page 105 HI-70 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-685-A HI-70 BOARD, COMPLETE (SERVICE) C739 1-164-943-11 CERAMIC CHIP 0.01uF C740 1-125-837-91 CERAMIC CHIP 6.3V ******************** (Ref.No. : 2000 Series) C741 1-117-919-11 TANTAL. CHIP 10uF 6.3V < BATTERY > C743 1-125-837-91 CERAMIC CHIP 6.3V...
  • Page 106 HI-70 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FERRITE BEAD > < RESISTOR > FB605 1-500-284-21 INDUCTOR CHIP 0UH R303 1-218-989-11 RES,CHIP 1/16W FB606 1-500-284-21 INDUCTOR CHIP 0UH R304 1-218-953-11 RES,CHIP 1/16W FB607 1-500-284-21 INDUCTOR CHIP 0UH R307 1-218-939-11 RES,CHIP 1/16W...
  • Page 107 LD-98 HI-70 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R671 1-218-953-11 RES,CHIP 1/16W R932 1-218-977-11 RES,CHIP 100K 1/16W R672 1-218-953-11 RES,CHIP 1/16W R933 1-218-977-11 RES,CHIP 100K 1/16W R934 1-218-990-11 SHORT R673 1-218-953-11 RES,CHIP 1/16W R674 1-218-985-11 RES,CHIP 470K 1/16W...
  • Page 108 PS-427 LD-98 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R433 1-218-973-11 RES,CHIP 1/16W R434 1-218-975-11 RES,CHIP 1/16W D401 8-719-067-36 DIODE MA3ZD1200LS0 R435 1-218-975-11 RES,CHIP 1/16W D402 8-719-073-01 DIODE MA111-(K8).S0 R436 1-218-957-11 RES,CHIP 2.2K 1/16W R437...
  • Page 109 PS-427 SY-56 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-686-A SY-56 BOARD, COMPLETE ******************** (Ref.No. : 1000 Series) Parts list of the SY-56 board is not shown. Pages from 6-13 to 6-14 are not shown. 6-13...
  • Page 110 SY-56 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCERRANEOUS ************* 1-675-589-21 FP-132 FLEXIBLE BOARD 1-960-051-11 HARNESS (MD-97) ! 58 1-418-657-11 FLASH UNIT (MC) 1-418-653-11 SWITCH BLOCK, CONTROL (PW) 1-960-050-11 HARNESS (MS-114) 1-960-061-11 HARNESS (GN-52) 1-675-590-11 FP-133 FLEXIBLE BOARD 1-418-237-21 TRANSFORMER UNIT, INVERTER 1-675-591-21 FP-134 FLEXIBLE BOARD 1-418-654-11 SWITCH BLOCK, CONTROL (FK)
  • Page 111 1-569-008-21 ADAPTOR, CONVERSION 2P (E) 1-573-856-11 ADAPTOR, CHANGE (JE) 1-769-608-21 CORD, POWER (AEP,UK,E,HK) 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK) 1-772-118-21 COMPACT DISK (Sony Picture Gear 3.2 Lite) (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-772-395-11 DISK, SYSTEM (USB DRIVER SOFT WARE) (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-782-984-31 CABLE, DIGITAL STILL CAMERA (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-783-738-31 CORD, CONNECTION (A/V connecting cable 1.5m)
  • Page 112 〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear DSC-F505 sheet for use. – 141 –...
  • Page 113 DSC-F505 Sony Corporation 99I0938-1 Personal VIDEO Products Company 9-974-192-31 Printed in Japan ©1999.9 – 142 – Published by Safety & Service Engineering Dept.
  • Page 114 DSC-F505 US Model Canadian Model SERVICE MANUAL AEP Model UK Model E Model Level 2 Hong Kong Model Level 3 Australian Model Chinese Model 2000. 03 Korea Model Tourist Model SUPPLEMENT-1 File this supplement-1 with the Service Manual. Addition of Adjustment item.
  • Page 115 DSC-F505 : Added portion. Page Changed contents 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 2. Zoom Center Adjustment Set the A/D value center of the microprocessor to the center voltage of the zoom key. If deviated, the zoom lens operates of itself, even if the zoom key is the center position.

This manual is also suitable for:

Cybershot dsc-f505

Table of Contents