Copyright 2012 by JVC KENWOOD Corporation. All The title to and ownership of copyrights for firmware rights reserved. embedded in Kenwood product memories are reserved for No part of this manual may be reproduced, translated, JVC KENWOOD Corporation. Any modifying, reverse en-...
RF power Type Choose the type of transceiver TX/RX 136~174 5.0W TK-2000 K,M A personal computer, programming interface (KPG-22A/22U), Transceiver programming and FPU (programming software) are required for programming. (The frequency, TX power HI/LOW, and signaling data are programmed for the transceiver.)
Page 4
TK-2000 REALIGNMENT 2. When the POWER is switched on, user mode can be Frequency (MHz) entered immediately. When the PC sends a command, 172.79375 the transceiver enters PC mode. 172.79500 When data is read from the transceiver, the red LED 172.80000...
Page 5
TK-2000 REALIGNMENT 4. Clone mode Note: Programming data can be transferred from one trans- • The Model name and Market codes must be the same in ceiver to another by connecting them via their SP/MIC con- order to clone the transceiver.
TK-2000 DISASSEMBLY FOR REPAIR 1. Separating the Case Assembly from the 2. Removing the TX-RX unit from the Chassis Chassis 1. Remove the two knobs ( a ). 1. Remove the packing ( e ). 2. Remove the two screws ( b ).
TK-2000 CIRCUIT DESCRIPTION 1. Frequency Confi guration The receiver utilizes double conversion. The first IF is 38.85MHz and the second IF is 450kHz. The fi rst Local os- cillator is supplied from the PLL circuit. The PLL circuit in the transmitter generates the neces- sary frequencies.
Page 8
TK-2000 CIRCUIT DESCRIPTION 2-3. IF Amplifi er Circuit 3. Transmitter System The fi rst IF signal is passed through a four-pole mono- 3-1. Microphone Amplifi er Circuit lithic crystal fi lter (XF200) to remove the adjacent channel The signal from microphone amplifi ed by IC301 and goes signal.
TK-2000 CIRCUIT DESCRIPTION Note: 4. Frequency Synthesizer Circuit The EEPROM stores tuning data (Deviation, Squelch, 4-1. Frequency Synthesizer etc.). The frequency synthesizer consists of the TCXO (X1), Realign the transceiver after replacing the EEPROM. VCO, PLL IC (IC1) and buffer amplifi ers.
TK-2000 SEMICONDUCTOR DATA MCU: F2136ACNKDRB (TX-RX unit IC400) Pin No. Signal Name Function Pin No. Signal Name Function VOXIN VOX level input VREF Reference voltage input CVDET VCO voltage detection MODE Mode select for MCU LSDO Low speed data output...
TK-2000 COMPONENTS DESCRIPTION TX-RX unit (X57-8093-00) Ref. No. Part Name Description Variable capaci- Ref. No. Part Name Description Frequency control/ VCO tance diode PLL system Variable capaci- Frequency control/ VCO IC200 FM IF system tance diode IC300 Diode TX/RX RF switch...
TK-2000 PARTS LIST ✽ New Parts. indicates safety critical components. L : Scandinavia K : USA P : Canada Parts without Parts No. are not supplied. Y : PX (Far East, Hawaii) T : England E : Europe Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Page 13
TK-2000 PARTS LIST TX-RX UNIT (X57-8093-00) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C122 CC73GCH1H470J CHIP C 47PF C247 CC73HCH1H470G CHIP C 47PF C123 CC73GCH1H100C CHIP C 10PF C248...
Page 14
TK-2000 PARTS LIST TX-RX UNIT (X57-8093-00) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation C360 CK73HB1A104K CHIP C 0.10UF L212 L40-8281-86 SMALL FIXED INDUCTOR(0.82UH) C397 CK73HB1H102K CHIP C 1000PF L213 L40-5681-86 SMALL FIXED INDUCTOR(0.56UH)
Page 15
TK-2000 PARTS LIST TX-RX UNIT (X57-8093-00) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R136 RK73HB1J182J CHIP R 1.8K 1/16W R331 RK73HB1J473J CHIP R 1/16W R139 RK73GB2A000J CHIP R 1/10W...
Page 16
TK-2000 PARTS LIST TX-RX UNIT (X57-8093-00) Desti- Desti- Ref. No. Address Parts No. Description Ref. No. Address Parts No. Description parts nation parts nation R505 RK73HB1J473J CHIP R 1/16W Q501 SSM3J05FU-F R508 RK73HB1J473J CHIP R 1/16W Q502 RT1P237U-T111 TRANSISTOR R509...
TK-2000 EXPLODED VIEW S400 Cx13 MIC300 J301 J300 VR500 CF200 S402 CD200 TX-RX unit A : N09-2438-05 B : N30-2606-48 C : N83-2005-48 Parts with the exploded numbers larger than 700 are not supplied. If a part reference number is listed in a box on the exploded view of the PCB, that part does not come with the PCB.
TK-2000 ADJUSTMENT Test Equipment Required for Alignment Test Equipment Major Specifi cations Frequency Range 136 to 174MHz Standard Signal Generator (SSG) Modulation Frequency modulation and external modulation Output –127dBm/0.1µV to greater than –47dBm/1mV Input Impedance 50Ω RF Power Meter Operation Frequency...
Page 19
TK-2000 ADJUSTMENT Frequency and Signaling Preparations for Tuning the Transceiver The transceiver has been adjusted for the frequencies Before attempting to tune the transceiver, connect the shown in the following table. When required, re-adjust them unit to a suitable power supply.
Page 20
TK-2000 ADJUSTMENT Common Section Measurement Adjustment Item Condition Specifi cations / Remarks Test- Unit Terminal Unit Parts Method equipment 1. Setting 1) BATT terminal voltage: 7.5V 2) SSG standard modulation [Wide] MOD: 1kHz, DEV: 3kHz [Narrow] MOD: 1kHz, DEV: 1.5kHz 2.
Page 21
TK-2000 ADJUSTMENT Receiver Section Measurement Adjustment Item Condition Specifi cations / Remarks Test- Unit Terminal Unit Parts Method equipment 1. Sensitivity 1) Adj item: Low, High (2 points) TX-RX ANT Check 12dB SINAD or more Check SSG output: –115dBm SP/MIC [Narrow] (0.4µV)
FM Hum & Noise ..........45dB (Wide) / 40dB (Narrow) Modulation Distortion ........... Less than 5% Guaranted frequency range ......... 144~174MHz (K) Measurements made per TIA/EIA-603 and specifi cations shown are typical. JVC KENWOOD Corporation reserves the right to change specifi cations without prior notice or obligation.
Need help?
Do you have a question about the TK-2000 and is the answer not in the manual?
Questions and answers