Page 1: Table Of Contents
XG-NV7XU SERVICE MANUAL S09P7XG-NV7XU DLP PROJECTOR XG-NV7XU MODEL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS...
Page 2: Specifications
XG-NV7XU Specifications...
Page 3: Important Service Safety Notes
XG-NV7XU IMPORTANT SERVICE SAFETY NOTES Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per WARNING volt., or higher, sensitivity to measure the AC voltage...
Page 4: Note To Service Personnel
XG-NV7XU NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5...
Page 5: Lamp Replacement
» Priére de se procurer un capuchon d'optique acant » The color wheel is running at high speed. Do not d'entretien un modéle XG-NV7XU qui est livré sans. touch it nor bring anything nearby. » Le disque chromatique opère à une vitesse élevée. Ne pas le toucher ni apporter quoi que ce soit à...
Page 6: Cautions Concerning The Laser Pointer
XG-NV7XU Cautions Concerning the Laser Pointer "COMPLIES WITH 21 CFR SUBCHAPTER J" CAUTION SHARP ELECTRONICS CORPORATION SHARP PLAZA, MAHWAH, NEW JERSEY 07430 TEL : 1-800-BE-SHARP U.S.A. ONLY LASER RADIATION- DO NOT STARE INTO BEAM REMOTE CONTROL MODEL NO. : RRMCG1530CESA WAVE LENGTH : 650nm DC3V (1.5VX2PCS.)
Page 7: Power Unit
XG-NV7XU WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Page 8 XG-NV7XU Location of Controls...
Page 9: Operating The Wireless Mouse Remote Control
XG-NV7XU Operating the Wireless Mouse Remote Control Remote Control Front View Rear View MUTE button POWER buttons VOLUME buttons (ON/OFF) ( / ) LEFT-CLICK/ UNDO KEYSTONE/BLACK LASER POINTER/ button SCREEN button MENU button MOUSE/ RIGHT-CLICK/ ADJUSTMENT ENTER button buttons INPUT button...
Page 10: Using The Remote Control As A Wireless Mouse
XG-NV7XU Using the Remote Control as a Wireless Mouse The remote control has the following three functions: MOUSE/ADJUSTMENT switch • Projector control (Remote control) • Wireless mouse • Laser pointer MOUSE ADJ. MOUSE ADJ. Wireless mouse Projector control Laser pointer Remote Control/Mouse Receiver Positioning •...
Page 11: Operation Manual
XG-NV7XU Use as a Wireless Mouse Be sure the supplied remote mouse receiver is connected to your computer. Slide the MOUSE/ADJUSTMENT switch to MOUSE. MOUSE ADJ. Effective buttons in MOUSE mode LASER BLACK SCREEN POINTER LEFT-CLICK MOUSE RIGHT-CLICK ¥ The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer s operation manual for details of setting up/installing the mouse driver.
Page 12 XG-NV7XU Connection Pin Assignments...
Page 13 XG-NV7XU Dimensions Rear View Top View Side View (235) Front View (212) Bottom View Units: inches (mm)
Page 14: Removing Of Major Parts
XG-NV7XU REMOVING OF MAJOR PARTS 1. Removing the Lamp Unit 1-1. Remove the screw from the lamp cover and detach the lamp cover. 1-2. Remove the three screws from the lamp unit and take out the lamp unit. Lamp Unit...
Page 15 XG-NV7XU 2. Removing the Top and Front Cabinets 2-1. Remove the two screws from the top and bottom cabinets. 2-2. Remove the three screws from the top and front cabinets. 2-3. Slowly lift the back of the top cabinet and disconnect the operation key unit connector (KY) and the speaker connector (SP).
Page 16: Removing The Pwb Units
XG-NV7XU 3. Removing the PWB Units 3-1. Remove the four screws from the output unit and disconnect the color wheel unit connector (J501). 3-2. Disconnect the output unit from the PC I/F unit connector. Tilt this unit toward the optical mechanism unit.
Page 17 XG-NV7XU 4. Removing the Power/Ballast Unit 4-1. Remove the two lock screws off the Inlet Ass’y. 4-2. Remove the screw from the bimetal cover and detach this cover 4-3. Remove the two screws from the bimetal assembly and detach this assembly.
Page 18 XG-NV7XU 5. Removing the Optical Mechanism and Lamp Housing 5-1. Remove the two screws from the lamp housing and detach the housing. 5-2. Remove the four screws from the optical mechanism unit and detach this unit. `: When removing these screws, be careful not to damage the capacitors nearby.
Page 19: Resetting The Total Lamp Timer
· Cooling fan breakdown. · Take the projector to your nearest Au- · Internal circuit failure. thorized Sharp Industrial DLP Products Dealer or Service Center for repair. LAMP REPLACE- The lamp does · Burnt-out lamp. · Carefully replace the lamp.
Page 20: Optical Adjustment
XG-NV7XU OPTICAL ADJUSTMENT What to readjust after replacement Readjustment Reflection lens Not needed. Cylinder mirror Not needed. Mirror A Not needed. Mirror B Not needed. Requirements for adjustments Phillips screwdriver, red gradation pattern signal. Enter the red gradation pattern from RGB1. Make sure the pattern Color wheel appears normal on screen.
Page 21: Dmd And Principle Of Optical System
XG-NV7XU DMD AND PRINCIPLE OF OPTICAL SYSTEM 1. Outline of DMD (Digital Micro Mirror Device) The DMD is one of the ultra-micro electromechanical systems called MEMS (Microeletromechanical System). The DMD can be fabricated by employing the existing 0.8 micron rule, which is the established semiconduc- tor manufacturing technology.
Page 22 XG-NV7XU 3. Switching of Mirror The mirror reflects light in one of two directions, By combining the DMD with a suitable light source and depending of the state of underlying memory cell. The projection optics ( Figure 6. ), the mirror reflects incident...
Page 23 XG-NV7XU 4. Digital Light Processing Signal and Gray Scale When the mirror rotates, it reflects incident light either into or out of the projection lens to create a burst of digital light pulses, which the eye interprets as an analog G R B image.
Page 24: Electrical Adjustment
XG-NV7XU ELECTRICAL ADJUSTMENT Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. Adjusting point Adjusting conditions Adjusting procedure » Make the following settings: EEPROM 1.
Page 25 XG-NV7XU Adjusting point Adjusting conditions Adjusting procedure » With the set's control switch or the remote-control Gain adjustment 1. Make the following choice. Group : A/D button, adjust the data until the white-side noise Subject : GAIN becomes bitless. Initial value : 137 »...
Page 26 XG-NV7XU Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller Video AGC 1. Feed the split color bar sig- nal. buttons, adjust the black-to-white (100%) level Group : VIDEO 1 difference to 1.65 ±0.02 Vp-p.
Page 27 XG-NV7XU Adjusting point Adjusting conditions Adjusting procedure » Using the control switches or the remote controller PAL color 1. Feed the PAL color bar sig- saturation level nal. buttons, adjust the difference between the 100% Group : VIDEO 1 white portion and the red portion to 0.28 ±0.02 Vp-p.
Page 28 XG-NV7XU Adjusting point Adjusting conditions Adjusting procedure » Adjust the level difference between the 100% white DVD Color 1. Feed the color bar signal of the 480I component signal to and red portions to 0.1 ±0.02 Vp-p. the D-SUB input terminal.
Page 29 XG-NV7XU Adjusting point Adjusting conditions Adjusting procedure » Make sure the “TEMP” is displayed. Thermistor 1. Heat the thermistor using a performance dryer. check » Call the VGA/S-VGA/XGA/SXGA/UXGA mode and Automatic 1. Receive the PHASE check synchronization pattern signal. make sure that the clock, phase, horizontal and RGB1 vertical positions can be automatically adjusted.
Page 30: Adjusting The Pc Interface
XG-NV7XU ADJUSTING THE PC INTERFACE (CPCi-0036CE01. PC I/F Unit) 1. Initializing the EEPROM 1) Press the S5001 switch to call the process mode. 2) Pick up the item S1 on the SSS menu. (The S1 is used to initialize the PC interface alone. Do not select the item S2 because otherwise the other data than the PC interface will be initialized.)
Page 31: Trouble Shooting Table
XG-NV7XU TROUBLE SHOOTING TABLE Checking the PWB performance Video input in trouble RGB input in trouble Remote control in trouble Go to "Checking the video unit Feed test pattern signal from Go to "Checking the remote circuit". control". Is specified cable connected between PC and projector? Use specified cable.
Page 32 XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Checking the video system Is the lamp on? Go to "Lamp fails to light-up". Are specified voltage fed to PA and PB connectors? Check the power circuit and its parts. Are there signal inputs at pins (12),...
Page 33: Checking The Video Unit Circuit
XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Checking the Video unit circuit Is there video signal output at pin (7) of IC3401? Check the IC3401 selector switch, terminal voltage and input circuit. Is there video signal input at IC4001? Check the low-pass and buffer circuits of Q4002 thru Q4005.
Page 34 XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Checking IC801 (RGB signal output circuit) Are there RGB output waveforms at pins (31), (32) and (33) of IC801? Go to "No color or unusual tone", Check the data transfer and other "No Y signal" or "Out of sync".
Page 35 XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Checking IC6008 (3-D noise reduction circuit) and its peripheral circuits Are there signal inputs at pins (40) (Y signal) and (45)(chroma signal) of IC6008? Check the buffer circuit of Q6001, Q6003, Q6004, Q6006 and Q6007 as well as Q6009 and Q6010.
Page 36: No Or Unusual Horizontal Sync
XG-NV7XU TROUBLE SHOOTING TABLE (Continued) No or unusual Y signal Is there Y signal input at pin (21) of IC801? Go back to the signal processing block. Is there Y signal output at pin (40) of IC801? Check IC801 and its peripheral circuits.
Page 37: No Audio Output
XG-NV7XU TROUBLE SHOOTING TABLE (Continued) No audio output Is there audio signal inputs at pin (2) of IC302? Check the input, the switching circuit of IC3301 and IC3302, and their peripheral circuit. Is there audio signal outputs at pin (7)
Page 38 XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Power on Is the right input selected? Select the right input with remote control. Are the PC, video and LCP cables as specified and properly connected? Use the right cables or reconnect the cables. With the contrast control at maximum, does the image appear? Readjust the video system.
Page 39: Lamp Fails To Light-Up
XG-NV7XU TROUBLE SHOOTING TABLE (Continued) Lamp fails to light-up Turn on the power switch. Is discharging sound heard from the lamp? Is the lamp out of socket? Are the cooling fans running? Replace the Reconnect the lamp. lamp into socket.
Page 40 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-1 Checking the clock circuit and its peripheral circuits Is X8001 (6MHz) oscillating? X8001 or its peripheral part faulty. Is X8002 (32.768kHz) oscillating? X8002 or its peripheral part faulty. Is X8003 (1.84MHz) oscillating? X8003 or its peripheral part faulty.
Page 41 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-2 Checking the sync signal circuit and its peripheral parts Is the sync signal of separate type? Are there signals at TP4 and TP5? IC302 or terminal unit defective. Is the sync signal SYNC ON GREEN?
Page 42 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-3 Checking the SXGA Checking the VGA red video circuit red video circuit and its peripheral and its peripheral parts parts Is there signal at pin (6) of IC8067? Is there signal at pin (6) of IC8067? Terminal unit, IC301, IC313 or IC312 defective.
Page 43 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-4 Checking the SXGA Checking the VGA green video circuit green video circuit and its peripheral and its peripheral parts parts Is there signal at pin (6) of IC8066? Is there signal at pin (6) of IC8066? Terminal unit, IC301, IC313 or IC312 defective.
Page 44 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-5 Checking the SXGA Checking the VGA blue video circuit blue video circuit and its peripheral and its peripheral parts parts Is there signal at pin (6) of IC8065? Is there signal at pin (6) of IC8065? Terminal unit, IC301, IC313 or IC312 defective.
Page 45 XG-NV7XU TROUBLE SHOOTING TABLE FOR PC I/F UNIT-6 Checking the OSD circuit and its peripheral circuits Display OSD on the screen. Are there signals at pins (56), (58), (71) and (72) of IC8048 (TL8054, TL8053, TL8052 and TL8051)? IC8029 or its peripheral circuit faulty.
Page 46: Chassis Layout
XG-NV7XU CHASSIS LAYOUT MAIN UNIT DUNTK9965DE01 BALLAST UNIT 9FU768815400 TERMINAL UNIT DUNTK9966DE01 PC I/F UNIT CPCI-0036CE01 R/C UNIT DUNTK9967DE01 POWER UNIT 9FU768813500 OUTPUT UNIT 9FU768550000 S-OUT UNIT DUNTK9968DE01...
Page 47: Block Diagram
XG-NV7XU BLOCK DIAGRAM TERMINAL UNIT...
Page 48: Overall Wiring Diagram
XG-NV7XU OVERALL WIRING DIAGRAM TERMINAL...
Page 49: Description Of Connector
XG-NV7XU DESCRIPTION OF CONNECTOR P8503 Pin No. Pin Name Signal Name Description 1, 3, 5 7, 9, 11 P12V +12V 13, 15, 17, 19 P3P3V +3.3V Serial BUs CLock C bus clock Serial BUs Date C bus data OLACT Overlay Active...
Page 50: Description Of Schematic Diagram
XG-NV7XU DESCRIPTION OF SCHEMATIC DIAGRAM VOLTAGE MEASUREMENT CONDITION: CAPACITOR 1. All capacitors are µF, unless otherwise noted. 1. Voltages at test points are measured at the (P=pF=µµF). supply voltage of AC 120V. Signals are fed by a 2. All capacitors are 50V, unless otherwise noted.
Page 51 XG-NV7XU Ë MAIN UNIT-1/7...
Page 52 XG-NV7XU Ë MAIN UNIT-2/7...
Page 53 XG-NV7XU Ë MAIN UNIT-3/7...
Page 54 XG-NV7XU Ë MAIN UNIT-4/7...
Page 55 XG-NV7XU Ë MAIN UNIT-5/7...
Page 56 XG-NV7XU Ë MAIN UNIT-6/7...
Page 57 XG-NV7XU Ë MAIN UNIT-7/7...
Page 58 XG-NV7XU Ë TERMINAL UNIT...
Page 59 XG-NV7XU Ë SOUND OUT UNIT...
Page 60 XG-NV7XU Ë R/C RECEIVER UNIT...
Page 61 XG-NV7XU Ë OPERATION KEY UNIT...
Page 62 XG-NV7XU Ë PC I/F UNIT-1/12...
Page 63 XG-NV7XU Ë PC I/F UNIT-2/12...
Page 64 XG-NV7XU Ë PC I/F UNIT-3/12...
Page 65 XG-NV7XU Ë PC I/F UNIT-4/12...
Page 66 XG-NV7XU Ë PC I/F UNIT-5/12...
Page 67 XG-NV7XU Ë PC I/F UNIT-6/12...
Page 68 XG-NV7XU Ë PC I/F UNIT-7/12...
Page 69 XG-NV7XU Ë PC I/F UNIT-8/12...
Page 70 XG-NV7XU Ë PC I/F UNIT-9/12...
Page 71 XG-NV7XU Ë PC I/F UNIT-10/12...
Page 72 XG-NV7XU Ë PC I/F UNIT-11/12...
Page 73 XG-NV7XU Ë PC I/F UNIT-12/12...
Page 74 XG-NV7XU Ë PC I/F (SUB UNIT-1)
Page 75 XG-NV7XU Ë PC I/F (SUB UNIT-2)
Page 76: Printed Wiring Board Assemblies
XG-NV7XU PRINTED WIRING BOARD ASSEMBLIES Main Unit (Wiring Side)
Page 77 XG-NV7XU Main Unit (Component Side)
Page 78 XG-NV7XU PC I/F (Sub Unit-1) PC I/F (Sub Unit-2) (Wiring Side) (Wiring Side) PC I/F Unit (Wiring Side)
Page 79 XG-NV7XU PC I/F Unit (Component Side)
Page 80 XG-NV7XU Sound Out Unit (Wiring Side) R/C Receiver Unit (Wiring Side) Terminal Unit (Wiring Side)
Page 81 XG-NV7XU Sound Out Unit (Component Side) R/C Receiver Unit (Component Side) Terminal Unit (Component Side)
Page 82 XG-NV7XU Operation Key Unit (Wiring Side) Operation Key Unit (Component Side)
Page 83: Parts List
For location of SHARP Parts Distributor, IC4512 RH-iX2963CEZZ J X24645S8T2 Please call Toll-Free; 1-800-BE-SHARP IC4514 VHiPQ20VZ11-1 J PQ20VZ11 IC5201 VHiM62352GP-1 J M62352GP in CANADA: Contact SHARP Electronics of Canada Limited IC5340 VHiM62320FP-1 J M62320FP Phone (416) 890-2100. IC6001 VHiNJM2240M-1 J NJM2240M IC6003 VHiBA7046F/-1 J BA7046F...
Page 84 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 COILS AND FILTERS FL4001 RCiLF0316CEZZ J Filter MAIN UNIT (Continued) FL4002 RCiLF0316CEZZ J Filter FL4501 RCiLF0306CEZZ J Filter Q4307 VS2PD601AR/-1 J 2PD601AR FL4502 RCiLV0108GEZZ J Band-Pass Coil...
Page 85 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 C4308 VCKYCY1HB103K J 0.01 Ceramic C4309 VCKYCY1HB103K J 0.01 Ceramic MAIN UNIT (Continued) C4310 VCKYCY1HB103K J 0.01 Ceramic C4311 VCKYCY1HB103K J 0.01 Ceramic C847 VCCCCY1EH102J J 1000p 25V...
Page 86 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 C6062 VCKYCY1CF104Z J 0.1 Ceramic C6063 VCKYCY1HB103K J 0.01 Ceramic MAIN UNIT (Continued) C6064 VCKYCY1CF104Z J 0.1 Ceramic C6065 VCKYCY1CF104Z J 0.1 Ceramic C4560 VCKYCY1CF104Z J 0.1...
Page 87 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 R872 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide R873 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide MAIN UNIT (Continued) R874 VRS-TX2HF5R6J J 5.6 1/2W Metal Oxide R875 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide...
Page 88 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 R4513 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide R4514 VRS-CY1JF102J J 1.0k 1/16W Metal Oxide MAIN UNIT (Continued) R4515 VRS-CY1JF100J J 10 1/16W Metal Oxide R4516 VRS-CY1JF182J J 1.8k 1/16W Metal Oxide...
Page 89 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 R6046 VRS-CY1JF822J J 8.2k 1/16W Metal Oxide R6047 VRS-CY1JF101J J 100 1/16W Metal Oxide MAIN UNIT (Continued) R6048 VRS-CY1JF471J J 470 1/16W Metal Oxide R6049 VRS-CY1JF104J...
Page 90: Terminal Unit
XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9965DE01 DUNTK9966DE01 MAIN UNIT (Continued) TERMINAL UNIT INTEGRATED CIRCUITS R7203 VRS-CY1JF393J J 39k 1/16W Metal Oxide R7250 VRS-CY1JF184J J 180k 1/16W Metal Oxide IC3001 VHi24LC21//-1 J 24LC21T R7251 VRN-CY1JF242D J 2.4k 1/16W Metal Film...
Page 91 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9966DE01 R3316 VRS-CY1JF000J 1/16W Metal Oxide R3401 VRS-TW2ED750J J 75 1/4W Metal Oxide TERMINAL UNIT (Continued) R3402 VRS-TW2ED750J J 75 1/4W Metal Oxide R3403 VRS-CY1JF123J J 12k 1/16W Metal Oxide...
Page 92 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTK9966DE01 C7208 VCEAPF1CW226M J 22 Electrolytic C7209 VCEAPV1CW226M J 22 Electrolytic TERMINAL UNIT (Continued) C7212 VCEAPV1CW476M J 47 Electrolytic C7214 VCEAPV1CW226M J 22 Electrolytic C7217 VCKYCY1CF104Z J 0.1...
Page 93 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 IC8314 9DK001-12067 J TC7SET08FU IC8315 9DK001-12067 J TC7SET08FU PC I/F UNIT IC8901 9DK001-12073 J GAL16LV8D-3LJ IC8903 9DK001-12055 J TC7WH241FU INTEGRATED CIRCUITS IC8904 9DK001-12055 J TC7WH241FU IC8001 RH-iX3270CEZZ...
Page 94 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 C8009 9DK001-42096 J 0.01 Ceramic C8012 9DK001-42103 J 15p Ceramic PC I/F UNIT (Continued) C8013 9DK001-42103 J 15p Ceramic C8014 9DK001-42096 J 0.01 Ceramic FL8011 9DK001-82020...
Page 95 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 C8189 9DK001-40091 J 100 Electrolytic C8190 9DK001-42096 J 0.01 Ceramic PC I/F UNIT (Continued) C8191 9DK001-42096 J 0.01 Ceramic C8192 9DK001-42096 J 0.01 Ceramic C8109 9DK001-42094 J 0.1...
Page 96 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 C8388 9DK001-42096 J 0.01 Ceramic C8389 9DK001-42096 J 0.01 Ceramic PC I/F UNIT (Continued) C8390 9DK001-42109 J 4700p 50V Ceramic C8391 9DK001-42094 J 0.1 Ceramic C8283 9DK001-42096 J 0.01...
Page 97 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 C8551 9DK001-42094 J 0.1 Ceramic C8552 9DK001-42115 J 10p Ceramic PC I/F UNIT (Continued) C8553 9DK001-42094 J 0.1 Ceramic C8554 9DK001-42118 J 10 Ceramic C8470 9DK001-43019 J 47 6.3V Tantalum...
Page 98 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 R8123 9DK001-50165 J 100 1/16W Chip1608 R8124 9DK001-50195 J 300(F) 1/16W Chip1608 PC I/F UNIT (Continued) R8125 9DK001-50197 J 2.7k 1/16W Chip1608 R8126 9DK001-50185 J 10k...
Page 99 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 R8354 9DK001-50185 J 10k 1/16W Chip1608 R8355 9DK001-50162 J 56 1/16W Chip1608 PC I/F UNIT (Continued) R8357 9DK001-50162 J 56 1/16W Chip1608 R8360 9DK001-50185 J 10k...
Page 100 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 R8601 9DK001-50159 J 22 1/16W Chip1608 R8602 9DK001-50159 J 22 1/16W Chip1608 PC I/F UNIT (Continued) R8603 9DK001-50159 J 22 1/16W Chip1608 R8604 9DK001-50159 J 22...
Page 101 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 R8932 9DK001-50230 J 18 1/4W Chip3216 R8933 9DK001-50185 J 10k 1/16W Chip1608 PC I/F UNIT (Continued) R8934 9DK001-50185 J 10k 1/16W Chip1608 R8935 9DK001-50149 1/16W Chip1608...
Page 102: Ë Cabinet And Mechanical Parts
XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-0036CE01 XBBSD30P08000 J Screw, x3 XBBSN30P06000 J Screw, x2 PC I/F (SUB UNIT-1) Not Available – Terminal Unit — PSLDM1000CEFW J Shield INTEGRATED CIRCUITS PSLDM1001CEFW J Earth Spring...
Page 103 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS (1/2) S-11 S-10 S-10...
Page 104 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS (2/2) 9FU768810600 J Bottom Cabinet 9FU768098107 J Lamp Cover Ass’y 9FU768810800 J Front Adjuster, x2 9FU768098109 J Rear Adjuster 9FU768524100 J Cooling Fan...
Page 105 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS (2/2) S-13 S-11 S-11 S-11...
Page 106 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS 9FU768376000 J Lens Cap 9FU768098100 J Optics Mecha. Ass’y 9FU768081020 J Optics Mecha. Base 9FU768810100 J Lens Unit 9FU768091560 J Condenser Lens 9FU768091680 J Spherical Mirror Ass’y 9FU768091730 J Cylinder Mirror Ass’y...
Page 107 XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS S-13 S-13 S-13...
Page 108: Supplied Accessories
XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) ACCESSORIES SPAKC5361CEZZ – Packing Case — SPAKP0858CEZZ – Polystyrene Cover — å QACCU5013CEZZ J AC Cord SPAKX2890CEZZ – Buffer Material —...
Page 109: Packing Of The Set
XG-NV7XU Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET CD-ROM Guarantee Card Operation Manual Quick Reference CD-ROM Manual Carrying Bag CD-ROM Quick Reference Soft Wear Caution IrDA Driver Installation Instruction Sheet Buffer Material...
Page 110 Code Ref. No. Part No. Description Code COPYRIGHT © 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Sharp XG-NV7XU Service Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Sharp XG-NV7XU

Summary of Contents for Sharp XG-NV7XU

Table of Contents