SERVICE MANUAL MODEL MODEL DEST. CHASSIS NO. DEST. CHASSIS NO..................PVM-14L5 US/CND SCC-G61K-A PVM-20L5 US/CND SCC-G61L-A PVM-D14L5A SCC-H03D-A PVM-D20L5A SCC-H03E-A REVISED-1 TRINITRON COLOR VIDEO MONITOR ®...
Page 2
LES SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE LISHED BY SONY.
Section 1 Service Informations 1-1. Board Layout (14 inch) 1-2. Disassembly (14 inch) 1-2-1. Top Cover Removal (14 inch) 2 Three screws (claw case screw (OS)) Top cover Rear cover 1 Three screws (claw case screw (OS)) 3 Two screws (+BVTT 4 x 8) PVM-14L5/20L5/D14L5A/D20L5A...
1-2-8. K, T, B1, M and B Boards Removal (14 inch) 9 Four screws (+BVTT 3 x 8) CN1901 (board to board) 2 K board CN3504 5 B1 board CN3505 3 Two PWB holders CN3503 T board CN3502 6 M board 1 Three PWB CN3501 CN107 (board to board)
1-2-10. Removal of Anode Cap Short-circuit the anode of the picture tube and the anode cap to the metal chassis, picture tube shield or carbon painted on the picture tube, after removing the anode..Removal Procedure Anode button (1) Turn up one side of the rubber cap in the (2) Using a thumb, pull up the rubber cap...
1-2-13. Speaker Removal (14 inch) 1 Four screws (step screw M3 x 4) 2 Four speaker cushions 3 Speaker 1-2-14. Service Position (14 inch) * Because there exist the portions that have the high tension voltage, be careful that the printed boards must not touch each other nor must not touch with the chassis.
1-4. Disassembly (20 inch) 1-4-1. Top Cover Removal (20 inch) 2 Three screws (claw case screw (OS)) Top cover 1 Three screws (claw case screw (OS)) 3 Four screws (+BVTT 4 x 8) Rear cover 1-4-2. Bezel Assy Removal (20 inch) 3 Two screws (+B 3 x 8) 6 Two claws 10 pin...
1-4-3. HA Board Removal (20 inch) 2 Two wire holders 1 Three screws (+BVTP 3 x 12) 5 Four claws HA board 4 Three claws CN2902 CN2901 3 Four claws 1-4-4. HB Board Removal (20 inch) 2 Three wire holders 3 Control label (L) CN5005 CN5002...
1-4-13. Speaker Removal (20 inch) 1 Four screws (step screw M3 x 4) 2 Four speaker cushions 3 Speaker 1-4-14. Service Position (20 inch) * Because there exist the portions that have the high tension voltage, be careful that the printed boards must not touch each other nor must not touch with the chassis.
Service Mode . Oscilloscope This set is provided with a switch for service on the front Sony Tektronix 2465 or equivalent (with bandwidth of panel that can be used to make various adjustments. The 350 MHz) operation method of this switch is explained in detail below.
Page 24
5. Executing FACTROY LOAD 5. If any IC on the B board is replaced, perform all If the adjustment data is damaged or lost by some adjustment items of the [SIGNAL] menu and of the reasons, you can restore the default factory adjustment [DEFLECTION] menu.
Page 25
Service Mode screen display SIGNAL LEVEL-1 SIG • LEVEL-1... SIG • Y BLACK • LEVEL-2... • PB BLACK • WHITE BALANCE... • PR BLACK • DECODER COLOR... • CHROMA PB • DECODER LEVEL... • CHROMA PR • DETECTION... • Y LEVEL •...
Page 26
FOCUS DEFLECTION DEFLECTION SIG • FOCUS... • H DUTY • RASTER H... • HFV SENSE • RASTER V... • HFV CONTROL • GEOMETRY... • H DF PHASE • H DF PARA • LANDING • H PLL LOCK RASTER H DEFLECTION H SIZE •...
Page 27
W/B DESCRIPTION SYSTEM SYSTEM SIG VERSION • COL1 • MODEL GRADE L4/L3 • COL2 • MODEL TYPE • W/B DESCRIPTION... • AGING MODE • FACTORY... • SIGNAL... • MAINTENANCE ID AGING MODE All white screen To return to the original screen, press the button of the input selector illuminating in orange.
Page 28
STATUS SIG ADJUST ERROR ABNORMAL I2C NVM BOARD B NVM BOARD B1 ENGINEER 1/3 ENGINEER 2/3 ENGINEER 3/3 AUSP SAMPLE POS DATA REFRESH H SYNC COUNT HIDE • • • • SREM RAW DATA • MENU DOTCLOCK • FACTORY SAVE... •...
Page 29
OPTION (BKM-150CP) OPTION OPTION OPTION SIG BKM-150CP (1/4) SIG BKM-150CP (2/4) SIG BKM-150CP (3/4) • OE • CCP P • SDTI SW • P SAVE • DA FV • TC MODE 0 • DISPLAY • DB FV • TC MODE 1 •...
Page 30
Name Description Inch20 Inch14 Name Description Inch20 Inch14 HFV_SENS Horizontal frequency 15K H_POSITION 480/60I Horizontal frequency 27K 575/50I Horizontal frequency 28K 1080/48I Horizontal frequency 31K 1080/50I Horizontal frequency 33K 480/60P Horizontal frequency 37K 576/50P Horizontal frequency 45K 1080/60I 1035/60I NORMAL 92 HFV_CONTROL Horizontal frequency 15K 1080/60I 1035/60I UNDER Horizontal frequency 27K...
Page 31
Name Description Inch20 Inch14 Name Description Inch20 Inch14 575/50I 4:3 UNDER PARA_CONTROL SIDE_PIN_W 1035/60I NORMAL 575/50I 16:9 NORMAL 1035/60I UNDER 575/50I 16:9 UNDER 1080/60I NORMAL 1080/48I NORMAL 1080/60I UNDER 1080/48I UNDER 720/50P NORMAL 1080/50I NORMAL 720/50P UNDER 1080/50I UNDER 720/60P NORMAL 480/60P 4:3 NORMAL 720/60P UNDER 480/60P 4:3 UNDER...
Page 32
Name Description Inch20 Inch14 Name Description Inch20 Inch14 SIDE_PIN_S 575/50I 16:9 UNDER TRAPEZOID 1080/60I NORMAL 1080/48I NORMAL 1080/60I UNDER 1080/48I UNDER 720/50P NORMAL 1080/50I NORMAL 720/50P UNDER 1080/50I UNDER 720/60P NORMAL 480/60P 4:3 NORMAL 720/60P UNDER 480/60P 4:3 UNDER V_SIZE 480/60I 4:3 NORMAL 480/60P 16:9 NORMAL 480/60I 4:3 UNDER...
Page 33
Name Description Inch20 Inch14 Name Description Inch20 Inch14 V_CENT 720/60P V_C_LIN 480/60P 16:9 NORMAL V_S_LIN 480/60I 4:3 NORMAL 480/60P 16:9 UNDER 480/60I 4:3 UNDER 575/50P 4:3 NORMAL 480/60I 16:9 NORMAL 575/50P 4:3 UNDER 480/60I 16:9 UNDER 575/50P 16:9 NORMAL 575/50I 4:3 NORMAL 575/50P 16:9 UNDER 575/50I 4:3 UNDER 1035/60I NORMAL...
Page 34
Name Description Inch20 Inch14 Name Description Inch20 Inch14 CHROMA_PB CHROMA PB V_BLK_T 1080/60I Y_BLACK SETUP-0 system 720/50P NTSC-0/BETA-0/SMPTE/SDI 720/60P SETUP-7.5 systemn V_BLK_B 480/60I NTSC-7.5/BETA-7.5 Not used PB_BLACK RGB/COMP Horizontal frequency 15K 575/50I Other than RGB/COMP Horizontal frequency 15K Not used NTSC/NTSC4.43/NOCOLOR60 80 1080/48I PAL/NOCOLOR50...
Page 35
Name Description Inch20 Inch14 Name Description Inch20 Inch14 PR_LEVEL AUTOSETUP-OFF PR_LEVEL AUTOSETUP-ON NTSC SETUP7.5 15kHz SMPTE(709) AUTOSETUP-ON Other than AUTOSETUP-OFF 180 (S)-NTSC SETUP7.5 15kHz SMPTE(709) AUTOSETUP-ON PAL AUTOSETUP-OFF AUTOSETUP-ON (S)-PAL 15kHz SMPTE(601) AUTOSETUP-ON SECAM Other than AUTOSETUP-OFF 140 15kHz SMPTE(601) AUTOSETUP-ON NTSC 443 100 AUTOSETUP-OFF AUTOSETUP-ON (S)-NTSC 443 150...
Page 36
Name Description Inch20 Inch14 Name Description Inch20 Inch14 PB_LEVEL AUTOSETUP-ON SUB_CONT H/V DELAY 15kHz SMPTE(601) 720/50P 16:9 NORMAL Other than AUTOSETUP-ON UNDER SACN 15kHz SMPTE(601) H/V DELAY AUTOSETUP-ON BETACAM SETUP 0(601) 720/60P 16:9 NORMAL AUTOSETUP-ON UNDER SACN BETACAM SETUP 7.5(601) H/V DELAY AUTOSETUP-ON SUB_BRIGHT Horizontal frequency 15K...
Page 37
Name Description Inch20 Inch14 Name Description Inch20 Inch14 B_GAIN COL1 15K 43MARKER_ 480/60I WIDTH Other than COL1 15K 575/50I COL2 15K 1080/48I Other than COL2 15K 1080/50I USER 15K 480/60P Other than USER 15K 576/50P B_BIAS COL1 15K 1080/60I 1035/60I NORMAL 10 Other than COL1 15K 1080/60I 1035/60I UNDER COL2 15K...
2-3. Preparation (2). Initialization Name Description Inch20 Inch14 SUBCON_ LINE-A (COMPOSITE) * Supply composite video or component signals as shown PHASE LINE-A (S) in Table 2-2. LINE-B (COMPOSITE) Signal Details of signal Standard level COMPONENT OPTION-A (Other than 129X) 50 Composite 358NT 100 % white...
2-4. Writing Model Data 2-5. Picture Output 1. Select the following submenus from the Service Menu 1. AC input voltage setting in the order of : [SYSTEM] → [MODEL GRADE] → 1. Input VIDEO signals and AUDIO signals to respective [MODEL TYPE] and write the model data of each terminals on the connector panel.
2-7. Landing Adjustment 14 inch 1. CONT ... MAX BRT ... Conspicuous position 2. Roughly adjust the white balance, G2, and conver- gence. 3. Switch the rotary SW of the single color switch to change the color into green only. 4.
2-8. H Blanking Adjustment 20 inch RASTER H H SIZE H CENTER H POSITION H BLK LEFT H BLK RIGHT 1. Connect the 480/60I cross hatch signal to the Y/G terminal of RGB/COMPONENT IN connector. 2. Press the UNDER SCAN button to enter the under scanned mode.
2-9. Linearity Adjustment 12. Repeat adjustments from step 5 to step 8 in the same way for each of the following signal frequencies. Find the following adjustment menu in the layer under the Horizontal frequency Signal specification ASPECT ratio DEFLECTION menu of the service mode. 15.625 kHz 575/50I 16 : 9/4 : 3...
2-10. Convergence Adjustment (1) 4. For HMC, use the BMC Mg to adjust the R and B dots so that they will be symmetrical horizontally with 1. Input a dot pattern signal. respect to the G dot. CONT ... Conspicuous position I’...
2-11. Deflection Yoke Neck Rotation 4. The following patterns cannot be corrected by turning Adjustment the neck. (Figs.2-25, 2-26, and 2-27) 1. If there is nonconvergence on both sides of the X or Y R G B axis of the screen, turn the neck of the deflection yoke * Gun rotatuon in the direction of the arrow to hold the nonconver- The X-axis and Y-axis...
2-14. White Balance Adjustment (15k) 1. Group of models 4 (See Table 2-3.) 1. Input a cross-hatch signal. 2. Make adjustment with the TLV, YCH, YBH VR, and XCV 1. Connect the 15K window signal to the Y/G terminal of coils of the deflection yoke to minimize nonconvergence.
2-15. White Balance Adjustment (33k) 2-16. SUB BRIGHT, SUB CONTRAST Adjustment (15 K) 1. Connect the 33K window signal to the Y/G terminal of 1. Input the 15 K monoscope signal to the COMPO- RGB/COMPONENT IN connector. NENT IN connector. 2.
2-17. SUB BRIGHT, SUB CONTRAST 2-18-2. PAL Composite Adjustment Adjustment (33 K) 1. Input a 625 all-white (with burst) cut-off signal to LINE A connector. 1. Input the 33 K monoscope signal to the COMPO- 2. Select LINE A from the operation panel. NENT IN connector.
2-18-5. HD and SDI Adjustments 3. Obtain the optimum focus on the corners of screen using [HDF|PARA] and [HDF|PHASE] of the 1. Install the BKM-142HD into the option slot. menu. 2. Select OPTION from the operation panel. 4. Connect the 480/60I all white signal to the Y/G 3.
3-1. High Tension Regulator Confirmation 3. Confirm that the voltage between the cathode and GND of D501 on the G board satisfies the standard value. Standard value : 20.5 ± 1.5 V 1. Turn the POWER OFF. (14 inch) 24.5 ± 1.5 V 2.
. Digital VOM Advantest TR6845 or equivalent . Oscilloscope . Variable auto-transformer . High tension voltmeter Sony Tektronix 2465 or equivalent (with bandwidth of . DC power supply 350 MHz) . NTSC/PAL/SECAM component signal generator . Ammeter Sony Tektronix TG2000 +AVG1 (option module) .
4-2. B Board Adjustments 2. Preparation of signals The B board can process various formats of video 4-2-1. Preparations signal. The B board must be adjusted for each type of video signal format respectively. Input the signals that Test point meet the following specifications to the connectors on the rear panel of the unit.
4-2-2. 15k YPBPR SMPTE (601) Signal 3. Connection diagram Adjustment (VG-854) (TG-2000) 4.2-2-1. Black Level Adjustment equivalent equivalent 1. Input the 15 kHz/60 Hz YPBPR SMPTE (601) 100 % color bar signal to the RGB/COMPONENT connector. 2. Press the RGB/CMPNT switch on the operation panel to select YPBPR.
4-2-2-3. MATRIX Adjustment 4-2-2-2. CHROMA Leak Adjustment 1. Connect an oscilloscope to TP1251. 1. Set the CHROMA to “0” using the PC tools. 2. Adjust the Y LEVEL (A2_87) data on the MENU so 2. Connect an oscilloscope to TP302. that the amplitude becomes the standard.
4-2-3. 15k YPBPR BETACAM SETUP 4-2-4. 15k YPBPR BETACAM SETUP 0 Signal Adjustment 7.5 Signal Adjustment 1. Input the 15 kHz/60 Hz YPBPR BETACAM SETUP 0 1. Input the 15 kHz/60 Hz YPBPR BETACAM SETUP color bar signal to the RGB/COMPONENT connector. 7.5 color bar signal to the RGB/COMPONENT 2.
4-2-5. 33 k YPBPR SMPTE (709) Signal 8. Connect an oscilloscope to TP1351. Adjustment 9. Adjust the PB LEVEL (A2_E4) data on the MENU so that the first step and the fourth step of the waveform have the same amplitude. 1.
Page 57
8. Connect an oscilloscope to TP1351. 9. Adjust the PB LEVEL (A2_E0) data on the MENU so that the first step and the fourth step of the waveform have the same amplitude. Adjust for the same amplitude 0 ±20 mV Fig.
4-3. B1 Board Adjustments 2. Preparation of signals Before starting the B1 board adjustment, be sure that The B board can process various formats of video adjustment of the B board has already been completed signal. The B board must be adjusted for each type of earlier.
4-3-2. Y OUT Level Adjustment (BYPASS 4-3-5. 3.58 f0 Adjustment (NTSC) Mode) 1. Input the NTSC 100 % color bar signal to the VIDEO 1. Input the Y-signal of the SMPTE/EBU N-10 level IN connector of INPUT A. without burst to the VIDEO IN connector of LINE A. 2.
4-3-8. Burst Gate Pulse Width Adjustment 4-3-7. Level Adjustment (NTSC) (PAL) 1. Input the NTSC 100% color bar signal to the VIDEO 1. Input the PAL 100 % color bar signal to the VIDEO IN connector of INPUT A. IN connector of INPUT A. 2.
4-3-11. PAL PHASE Adjustment (Normal) 4-3-13. Level Adjustment (NTSC 443) 1. Input the PAL SP color bar signal to the VIDEO IN 1. Input the NTSC 443 100 % color bar signal to the VIDEO IN connector of INPUT A. connector of INPUT A.
4-3-14. Clamp Pulse Width Adjustment 4-3-16. Level Adjustment (SECAM) (SECAM) 1. Input the SECAM 100 % color bar signal to the 1. Input the SECAM 100 % color bar signal to the VIDEO IN connector of INPUT A. VIDEO IN connector of INPUT A. 2.
Section 5 Theory of Operation 5-1. B Board 1. Input selector IC201 switches the input signals of either CN201 input (VIDEO1, 2, Y/C) or CN302 input (COM/RGB, OP1, 2). 2. Clamp circuit (1) Pedestal level of the Y/G signal is clamped to the pedestal voltage by the Y-CL-P pulse at IC202 (3/3) (analog switch) using the sample-and-hold circuit.
Page 64
9. ABL circuit The ABL circuit consists of Q2006 for PIC ABL and Q2005 for BRT ABL. Respective emitters receive the ABL voltage from deflection block and bases receive the DC voltages that are generated by voltage- dividing. Respective collectors are connected to pin-46 (PIC control) and pin-7 (BRT control of IC2001. When these transistors turn on, the respective control voltages decrease so that the ABL operation is implemented.
5-2. BI Board 1. Y/C Separator Circuit 1-1. NTSC/PAL mode The composite input signal that is input through the Q board is band-width limited by FL801, amplified by Q803/Q804, passed through the digital comb filter (IC801 pin-25) so that it is separated to the Y signal and the chroma signal.
6. PAL Low-pass Filter The R-Y signal that is output from IC2804 pin-23 passes through the active low-pass filter (Q3809, Q3810) and is input to IC3802 pin-16. IC3802 contains the built-in 1H delay circuit using a line memory. The output signal after 1H delay is added to the non-delayed signal at pin-11 and is output. The R-Y signal from pin-11 is output via the switch circuit (IC3804, IC3806) and the level adjustment circuit (IC3807).
5-4. Deflection Circuit and High Tension Circuit The following circuits consisting the deflection circuit and high-tension circuit, are contained the three circuit boards of G board, D1 board and D board. Parts and components in the G board have the parts reference number of 500 series. Parts and compo- nents in the D1 board have the parts reference number of 1500 series.
Page 68
Switching of the S-shape compensation capacitors is done by Q2512, Q2513, Q2514, Q2515, Q2509 and Q2510. Switching of the S-shape compensation capacitors is done at the three points of the horizontal frequency 15 kHz, 27 to 33.75 kHz and 37 to 45 kHz. Switching of the horizontal linearity coils is done by RY2501 when the 15 kHz signal is input.
5-5. Power Supply Circuit Power supply block of this circuit board consists of the two switching regulators as shown below. 1. Power factor improvement regulator to conform to the power supply higher harmonics regulation. 2. Main regulator that supplies the necessary voltages to the signal system circuit, deflection system/ high tension system circuits.
Page 70
3. Over-voltage protection circuit and over-current protection circuit The +135 V main power line contains the over-voltage protection circuit and over-current protection circuit that protect the power supply circuit and loads from getting damaged in the case of abnormal load or failure in the voltage feedback systems.
Ne les remplacer que par une pièce portant le numéro spécifié. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts List has the present standardized repair parts.
Top Cover Section (14 Inch) 7-2. Exploded Views +BVTP 3x12 +BVTT 4x8 +BVTT 4x8 +BVTP 3x12 +B 3x8 +BVTP 3x8 +BVTP 3x12 +BVTP 3x12 +B 3x8 Part No. SP Description Part No. SP Description 8-330-030-00 s MOUNTED CIRCUIT BOARD, H1 4-086-480-02 o LABEL (L), CONTROL 8-330-030-01 s MOUNTED CIRCUIT BOARD, H2 4-086-484-01 s BUTTON, POWER...
Page 77
Chassis Section (14 Inch) +PSW 4x8 +BVTT 3x8 +PSW 4x8 +BVTP 3x16 +PSW 4x8 +PSW +BVTP 3x12 3x12 +PSW 4x8 +BVTT 4x8 +BVTP 3x12 +BVTT 4x8 +PS 4x14 +PS 4x14 Part No. SP Description Part No. SP Description 8-330-030-02 s MOUNTED CIRCUIT BOARD, B 4-070-730-01 s HOLDER, PWB 8-330-030-03 s MOUNTED CIRCUIT BOARD, B1 4-086-472-01 s SCREW (M3X4), STEP...
Page 78
G Board Section (14 Inch) Q606 IC603 IC601 D628 IC607 D616 R564 R562 Q1615 IC606 Q504 D603 IC605 VDR602 Q505 Part No. SP Description Part No. SP Description 8-330-030-08 s MOUNTED CIRCUIT BOARD, G 4-061-191-01 s SHEET, INSULATE 1-453-391-11 s FBT ASSY (NX-4141//M3E4) 4-374-846-21 o COVER,CAPACITOR,CAP TYPE 1-576-231-11 s FUSE (H.B.C.) (4A/250V) 4-382-854-01 s SCREW +PSW M3X8(EP-FE/ZN/CM2)
Page 79
Picture Tube Section (14 Inch) Part No. SP Description 8-330-030-09 s MOUNTED CIRCUIT BOARD, C X-2105-533-1 s PLATE ASSY,CORRECTION,TLH 1-411-660-21 s COIL, DEMAGNETIC 1-451-508-11 s DEFLECTION YOKE 1-452-032-00 s MAGNET,DISC 4-035-160-01 s PURSE LOCK (S) (DIA. 12) 4-050-492-01 s SPACER, DY (CM) 4-051-735-42 s PIECE A(75), CONV, CORRECT 4-053-410-02 s SHIELD, DY...
Page 80
Top Cover Section (20 Inch) +BVTP 3x12 +BVTT 4x8 +BVTT 4x8 Part No. SP Description 8-330-030-26 s MOUNTED CIRCUIT BOARD, D 8-330-030-42 s MOUNTED CIRCUIT BOARD, D1 1-543-653-11 s CORE ASSY, BEAD 1-786-226-11 s SWITCH, AC POWER PUSH 3-703-354-41 s SCREW (OS), CASE, CLAW 4-043-825-01 s HANDLE 4-086-471-01 o INSULATOR (J PWB) 4-086-506-11 s COVER, TOP...
Page 81
Bezel Section (20 Inch) +BVTP 3x12 +B 3x8 +BVTP 3x12 +BVTP 3x12 +BVTP 3x12 +BVTP 3x12 +B 3x8 Part No. SP Description 8-330-030-22 s MOUNTED CIRCUIT BOARD, HA 8-330-030-23 s MOUNTED CIRCUIT BOARD, HB 8-330-030-11 s MOUNTED CIRCUIT BOARD, X X-4040-006-1 s BEZEL ASSY 3-701-822-00 s HOLDER, WIRE 4-086-484-01 s BUTTON, POWER...
Page 83
G Board Section (20 Inch) Q606 IC603 IC601 D628 IC607 D616 R564 R562 Q1615 IC606 Q504 D603 IC605 VDR602 Q505 Part No. SP Description Part No. SP Description 8-330-030-43 s MOUNTED CIRCUIT BOARD, G 2-371-561-00 s BUSHING(P),INSULATING X-4560-177-1 s FBT ASSY (NX-4141/J1A4)(PVM-20L5) 4-061-191-01 s SHEET, INSULATE 1-453-436-11 s FBT ASSY (NX-4141/M3D4)(PVM-D20L5A) 4-374-846-21 o COVER,CAPACITOR,CAP TYPE...
Page 84
Picture Tube Section (20 Inch) +BVTT 4x6 +BVTP 3x12 +BVTP 3x12 Part No. SP Description Part No. SP Description 8-330-030-44 s MOUNTED CIRCUIT BOARD, C 4-087-016-02 s BRACKET (R), TOP 1-411-657-11 s COIL, LANDING CORRECTION 4-087-017-02 s BRACKET (L), TOP 1-411-659-21 s COIL, DEMAGNETIC 4-303-774-99 s SPRING 1-451-553-11 s DEFLECTION YOKE...
7-3. Electrical Parts List ------- B BOARD (B BOARD) ------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description A-1300-101-B s MOUNTED CIRCUIT BOARD, B C131 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V (FOR PVM-14L5/D14L5A) C132 1-126-964-11 s CAPACITOR, ELECT 10MF/50V 8-330-030-24 s MOUNTED CIRCUIT BOARD, B...
Page 86
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description C317 1-126-935-11 s CAPACITOR,ELECT 470MF/16V C1070 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C318 1-126-935-11 s CAPACITOR,ELECT 470MF/16V C1071 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C319 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C1072...
Page 87
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description C1461 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C2312 1-163-005-11 s CAPACITOR CHIP CERAMIC 470PF C1462 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C2313 1-126-935-11 s CAPACITOR,ELECT 470MF/16V C1463 1-104-665-11 s CAPACITOR, ELECT 100MF/25V...
Page 88
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description DL352 1-416-476-21 s DELAY LINE IC1453 8-759-671-94 s IC MC74HC4053AFEL DL451 1-402-770-11 s DELAY LINE IC2001 8-752-067-05 s IC CXA1739S DL452 1-416-476-21 s DELAY LINE IC2041...
Page 89
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description Q263 8-729-107-31 s TRANSISTOR 2SC3545 Q1201 8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R Q264 8-729-112-65 s TRANSISTOR 2SA1462 Q1202 8-729-026-49 s TRANSISTOR 2SA1037AK-T146-R Q265 8-729-107-31 s TRANSISTOR 2SC3545 Q1203...
Page 90
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description Q2402 8-729-120-28 s TRANSISTOR 2SC1623-L5L6 1-216-079-00 s RESISTOR CHIP 18K 1/10W(2012) Q2403 8-729-120-28 s TRANSISTOR 2SC1623-L5L6 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) Q2404 8-729-112-65 s TRANSISTOR 2SA1462 1-216-059-00 s RESISTOR,CHIP 2.7K 1/10W(2012)
Page 91
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R150 1-216-001-00 s RESISTOR, CHIP 10 1/10W(2012) R269 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R151 1-216-001-00 s RESISTOR, CHIP 10 1/10W(2012) R270 1-216-085-00 s RESISTOR CHIP 33K 1/10W(2012) R153...
Page 92
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R356 1-216-057-00 s RESISTOR CHIP 2.2K 1/10W(2012) R467 1-216-631-11 s RESISTOR,CHIP 150 1/10W (2012) R357 1-216-053-00 s RESISTOR CHIP 1.5K 1/10W(2012) R468 1-216-631-11 s RESISTOR,CHIP 150 1/10W (2012) R358...
Page 93
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R1056 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R1256 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R1057 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R1257 1-216-653-11 s RESISTOR,CHIP 1.2K 1/10W(2012) R1058 1-216-659-11 s RESISTOR,CHIP 2.2K 1/10W(2012) R1258...
Page 94
(B BOARD) (B BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R1408 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R2031 1-216-121-00 s RESISTOR CHIP 1M 1/10W(2012) R1409 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) (FOR PVM-20L5/D20L5A) R1410 1-216-645-11 s RESISTOR,CHIP 560 1/10W(2012)
Page 95
-------- (B BOARD) B1 BOARD -------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R2304 1-216-063-91 s RESISTOR,CHIP 3.9K 1/10W(2125) A-1300-102-B s MOUNTED CIRCUIT BOARD, B1 R2305 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) R2306 1-216-017-91 s RESISTOR, CHIP 47 1/10W(2012) C801...
Page 96
(B1 BOARD) (B1 BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description C2807 1-163-263-11 s CAPACITOR CERAMIC 330PF/50V C3817 1-163-245-11 s CAPACITOR CERAMIC 56PF/50V C2808 1-107-715-11 s CAPACITOR,ELECT 22MF/50V (BP) C3818 1-163-227-11 s CAPACITOR CERAMIC 10PF/50V(CH) C2809 1-126-933-11 s CAPACITOR,ELECT 100MF/16V C3819...
Page 97
(B1 BOARD) (B1 BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description IC3804 8-759-710-86 s IC NJM2233BM Q3818 8-729-027-38 s TRANSISTOR DTA144EKA-T146 IC3807 8-752-053-21 s IC CXA1211M Q3819 1-801-806-11 s TRANSISTOR DTC144EKA IC4803 8-759-567-08 s IC MB88141APF-ER IC4804...
Page 98
(B1 BOARD) (B1 BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R868 1-216-057-00 s RESISTOR CHIP 2.2K 1/10W(2012) R2841 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) R869 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2012) R2842 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R870...
Page 99
(B1 BOARD) (B1 BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R3816 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2012) X2801 1-577-259-11 s VIBRATOR,CRYSTAL(17.734MHz) R3817 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2012) X2802 1-527-722-00 s CRYSTAL OSCILLATOR(14.31818MHz) R3818 1-216-651-11 s RESISTOR,CHIP 1K 1/10W(2012) R3819...
Page 100
------- C BOARD (C BOARD) ------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-09 s MOUNTED CIRCUIT BOARD, C D707 8-719-157-72 s DIODE RD22M-B (FOR PVM-14L5/D14L5A) D708 8-719-073-01 s DIODE MA111-(K8).S0 8-330-030-44 s MOUNTED CIRCUIT BOARD, C D709 8-719-051-85 s DIODE HSS83TD...
Page 101
---------------------------- (C BOARD) D BOARD(FOR PVM-14L5/D14L5A) ---------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R731 1-249-435-11 s RESISTOR CARBON 33K 1/4W A-1300-105-B s MOUNTED CIRCUIT BOARD, D R732 1-216-073-00 s RESISTOR,CHIP 10K 1/10W(2012) R733 1-216-065-91 s RESISTOR,CHIP 4.7K 1/10W(2012) C2501...
Page 102
(D BOARD(FOR PVM-14L5/D14L5A)) (D BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description D2501 8-719-159-12 s DIODE RD5.1SB2-T2 R2524 1-216-053-00 s RESISTOR CHIP 1.5K 1/10W(2012) D2502 8-719-908-03 s DIODE GP08D R2525 1-216-065-91 s RESISTOR,CHIP 4.7K 1/10W(2012) D2506 8-719-028-45 s DIODE D2L20U...
Page 103
---------------------------- D BOARD(FOR PVM-20L5/D20L5A) (D BOARD(FOR PVM-20L5/D20L5A)) ---------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-26 s MOUNTED CIRCUIT BOARD, D CN2512 1-691-291-11 o PIN,CONNECTOR(PC BOARD)5P C2501 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V D2501 8-719-159-12 s DIODE RD5.1SB2-T2 C2502...
Page 104
----------------------------- (D BOARD(FOR PVM-20L5/D20L5A)) D1 BOARD(FOR PVM-14L5/D14L5A) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R2523 1-216-081-00 s RESISTOR,CHIP 22K 1/10W(2012) A-1300-106-B s MOUNTED CIRCUIT BOARD, D1 R2524 1-216-053-00 s RESISTOR CHIP 1.5K 1/10W(2012) R2525 1-216-065-91 s RESISTOR,CHIP 4.7K 1/10W(2012) C1501...
Page 105
(D1 BOARD(FOR PVM-14L5/D14L5A)) (D1 BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description CN1503 1-785-517-11 o CONNECTOR, BOARD TO BOARD R1515 1-216-113-00 s RESISTOR CHIP 470K 1/10W(2012) CN1504 1-564-521-11 o PLUG,CONNECTOR (6P)(L-TYPE) R1517 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R1518...
Page 106
----------------------------- (D1 BOARD(FOR PVM-14L5/D14L5A)) D1 BOARD(FOR PVM-20L5/D20L5A) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R1579 1-216-675-11 s RESISTOR,CHIP 10K 1/10W(2012) 8-330-030-42 s MOUNTED CIRCUIT BOARD, D1 R1580 1-216-668-11 s RESISTOR,CHIP 5.1K 1/10W(2012) R1581 1-216-627-11 s RESISTOR,CHIP 100 1/10W (2012) C1501...
Page 107
(D1 BOARD(FOR PVM-20L5/D20L5A)) (D1 BOARD(FOR PVM-20L5/D20L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description CN1503 1-785-517-11 o CONNECTOR, BOARD TO BOARD R1515 1-216-113-00 s RESISTOR CHIP 470K 1/10W(2012) CN1504 1-564-521-11 o PLUG,CONNECTOR (6P)(L-TYPE) R1517 1-216-025-00 s RESISTOR,CHIP 100 1/10W(2012) R1518...
Page 108
---------------------------- (D1 BOARD(FOR PVM-20L5/D20L5A)) G BOARD(FOR PVM-14L5/D14L5A) ---------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R1579 1-216-678-11 s RESISTOR,CHIP 13K 1/10W(2012) 8-330-030-08 s MOUNTED CIRCUIT BOARD, G R1580 1-216-668-11 s RESISTOR,CHIP 5.1K 1/10W(2012) R1581 1-216-627-11 s RESISTOR,CHIP 100 1/10W (2012) C504...
Page 109
(G BOARD(FOR PVM-14L5/D14L5A)) (G BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description C618 1-163-139-00 s CAPACITOR,CHIP CERAMIC 820PF CN1607 1-564-509-11 o PLUG,CONNECTOR (6P) C619 1-107-905-11 s CAPACITOR,ELECT 4.7MF/50V CN1608 1-564-507-11 o PLUG,CONNECTOR (4P) C620 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V CN1609...
Page 110
(G BOARD(FOR PVM-14L5/D14L5A)) (G BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description FB606 1-410-397-21 s FERRITE BEAD INDUCTOR Q613 1-801-806-11 s TRANSISTOR DTC144EKA FB607 1-410-397-21 s FERRITE BEAD INDUCTOR Q614 8-729-140-96 s TRANSISTOR 2SD774-34 FB608 1-410-397-21 s FERRITE BEAD INDUCTOR...
Page 111
(G BOARD(FOR PVM-14L5/D14L5A)) (G BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R602 1-219-513-11 s RESISTOR 4.7M 1/2W (SURGE) R661 1-216-660-11 s RESISTOR,CHIP 2.4K 1/10W(2012) R603 1-219-513-11 s RESISTOR 4.7M 1/2W (SURGE) R662 1-216-675-11 s RESISTOR,CHIP 10K 1/10W(2012) R604...
Page 112
---------------------------- G BOARD(FOR PVM-20L5/D20L5A) (G BOARD(FOR PVM-20L5/D20L5A)) ---------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-43 s MOUNTED CIRCUIT BOARD, G C618 1-163-139-00 s CAPACITOR,CHIP CERAMIC 820PF C619 1-107-905-11 s CAPACITOR,ELECT 4.7MF/50V C504 1-163-031-11 s CAPACITOR, CHIP CERAMIC 0.01MF C620...
Page 113
(G BOARD(FOR PVM-20L5/D20L5A)) (G BOARD(FOR PVM-20L5/D20L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description CN1606 1-564-507-11 o PLUG,CONNECTOR (4P) FB605 1-410-397-21 s FERRITE BEAD INDUCTOR CN1607 1-564-509-11 o PLUG,CONNECTOR (6P) FB606 1-410-397-21 s FERRITE BEAD INDUCTOR CN1608 1-564-507-11 o PLUG,CONNECTOR (4P) FB607...
Page 114
(G BOARD(FOR PVM-20L5/D20L5A)) (G BOARD(FOR PVM-20L5/D20L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description Q611 8-729-033-24 s TRANSISTOR DTC114GKAT146 R565 1-216-645-11 s RESISTOR,CHIP 560 1/10W(2012) Q612 8-729-033-26 s TRANSISTOR DTA114GKAT146 R566 1-249-407-11 s RES,CARBON 150 1/4W (SMALL) Q613 1-801-806-11 s TRANSISTOR DTC144EKA R567...
Page 115
----------------------------- (G BOARD(FOR PVM-20L5/D20L5A)) H1 BOARD(FOR PVM-14L5/D14L5A) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R657 1-216-492-11 s RESISTOR,METAL FILM 82K/3W 8-330-030-00 s MOUNTED CIRCUIT BOARD, H1 R658 1-216-492-11 s RESISTOR,METAL FILM 82K/3W R659 1-215-929-11 s RESISTOR,METAL FILM 100K/3W C2901...
Page 116
----------------------------- (H1 BOARD(FOR PVM-14L5/D14L5A)) H2 BOARD(FOR PVM-14L5/D14L5A) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R2926 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 8-330-030-01 s MOUNTED C.BOARD,H2 COMPL R2927 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 R2928 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) C5001...
Page 117
(H2 BOARD(FOR PVM-14L5/D14L5A)) (H2 BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description Q5019 8-729-045-93 o TRANSISTOR IMZ4T108 R5048 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) Q5020 8-729-045-93 o TRANSISTOR IMZ4T108 R5049 1-216-821-11 s RESISTOR,CHIP 1.0K 1/16W(1608) Q5021 8-729-045-93 o TRANSISTOR IMZ4T108...
Page 118
(H2 BOARD(FOR PVM-14L5/D14L5A)) (H2 BOARD(FOR PVM-14L5/D14L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R5107 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 S5006 1-762-357-11 s SWITCH,TACTIL(LINE A) R5108 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) S5007 1-762-357-11 s SWITCH,TACTIL(LINE B) R5109...
Page 119
----------------------------- HA BOARD(FOR PVM-20L5/D20L5A) (HA BOARD(FOR PVM-20L5/D20L5A)) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-22 s MOUNTED CIRCUIT BOARD, HA R2926 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 R2927 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 C2901 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B R2928...
Page 120
----------------------------- HB BOARD(FOR PVM-20L5/D20L5A) (HB BOARD(FOR PVM-20L5/D20L5A)) ----------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-23 s MOUNTED CIRCUIT BOARD, HB Q5019 8-729-045-93 o TRANSISTOR IMZ4T108 Q5020 8-729-045-93 o TRANSISTOR IMZ4T108 C5001 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B Q5021...
Page 121
(HB BOARD(FOR PVM-20L5/D20L5A)) (HB BOARD(FOR PVM-20L5/D20L5A)) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R5048 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) R5107 1-216-804-11 s RESISTOR,CHIP 39 1/16W 1608 R5049 1-216-821-11 s RESISTOR,CHIP 1.0K 1/16W(1608) R5108 1-216-833-11 s RESISTOR,CHIP 10K 1/16W (1608) R5050...
Page 122
---------------------------- (HB BOARD(FOR PVM-20L5/D20L5A)) K BOARD(FOR PVM-14L5/D14L5A) ---------------------------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description S5006 1-762-357-11 s SWITCH,TACTIL(LINE A) 8-330-030-05 s MOUNTED CIRCUIT BOARD, K S5007 1-762-357-11 s SWITCH,TACTIL(LINE B) S5008 1-762-357-11 s SWITCH,TACTIL(RGB/COMP) C3501...
Page 123
---------------------------- ------- K BOARD(FOR PVM-20L5/D20L5A) M BOARD ---------------------------- ------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-25 s MOUNTED CIRCUIT BOARD, K 8-330-030-04 s MOUNTED CIRCUIT BOARD, M C3501 1-107-714-11 s CAPACITOR, ELECT 10MF/50V(BP) C1101 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V C3502...
Page 124
------- (M BOARD) Q BOARD ------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R1143 1-216-001-00 s RESISTOR, CHIP 10 1/10W(2012) C2700 1-126-514-11 s CAPACITOR,ELECT 22MF/16V R1144 1-216-001-00 s RESISTOR, CHIP 10 1/10W(2012) C2701 1-126-514-11 s CAPACITOR,ELECT 22MF/16V R1145...
Page 125
(Q BOARD) (Q BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description C3725 1-163-033-91 s CAPACITOR, CERAMIC 0.022MF/50V D3752 8-719-158-19 s DIODE RD6.2SB C3730 1-126-514-11 s CAPACITOR,ELECT 22MF/16V D3753 8-719-158-19 s DIODE RD6.2SB C3731 1-126-514-11 s CAPACITOR,ELECT 22MF/16V C3732...
Page 126
(Q BOARD) (Q BOARD) Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description R2740 1-214-837-11 s RESISTOR,METAL FILM 75,1/2W R3720 1-214-837-11 s RESISTOR,METAL FILM 75,1/2W R2741 1-216-049-11 s RESISTOR, CHIP 1K 1/10W(2012) R3721 1-216-089-91 s RESISTOR, CHIP 47K 1/10W(2012) R2742 1-216-093-00 s RESISTOR, CHIP 68K 1/10W(2012)
Page 127
------- ------- T BOARD X BOARD ------- ------- Ref. No. Ref. No. or Q’ty Part No. SP Description or Q’ty Part No. SP Description 8-330-030-10 s MOUNTED CIRCUIT BOARD, T 8-330-030-11 s MOUNTED CIRCUIT BOARD, X C1901 1-124-779-00 s CAPACITOR,ELECT 10MF/16V CN900 1-580-056-21 o PIN,CONNECTOR 3P C1902...
Overall (1/2) Overall (1/2) Section 8 Block Diagrams LINE A IC805 IC806 J2701 IC2780,2782 BYPASS Y GAIN VIDEO IC803 VIDEO/Y IC201 IC201 VIDEO J2704 VIDEO/Y IC202 IC204 IC251 CLAMP IC252 BUFF Y LEV Y CLP Y BLACK Y LEVEL APER LEV IC251 CN2702 IC2804...
Overall (2/2) Overall (2/2) T602 RECT +180V IC601 RECT +15V LINE IC604 AC IN FILTER RECT +12V RECT +12V IC606 T602 RECT PFCT OP +5V RECT OP +6V THP601 IC605 RECT IC602 RECT POWER OP -6V CONT IC607 RECT LED POWER LED DRIVE LED GRP0 -15V...
Q (1/2), B (1/5), T (1/2), K Q (1/2), B (1/5), T (1/2), K (1/2) (SIGNAL I/O) LINE A IC2780 VIDEO SW IC2782 J2701 BUFF VIDEO SW Q2700 (1/2) (1/5) VIDEO J2704 CN2704 CN1907 CN1901(1/3) CN302(1/3) CN301 BUFF VIDEO/Y VIDEO/Y VIDEO/Y VIDEO/Y VIDEO/Y...
Page 132
B (2/5) B (2/5) (2/5) (SIGNAL SELECT) IC201(1/3) IC202(2/3) Y/G OUT Y/G BUFF CLAMP BUFF Q201,202 Q203 Q204 IC202(1/3) IC203(1/2) IC203(2/2) CLAMP CLAMP IC204 IC251(1/2) IC252(1/2) IC252(2/2) BUFF BUFF BUFF BUFF Y BLACK Y AMP BUFF BUFF BUFF Q205 Q254 Q255 Q256 IC201(2/3)
Page 133
B (3/5) B (3/5) SIGNAL SELECT IC2001 IC1452(2/2) IC1453(3/3) (3/5) IC1453(2/3) RGB MATRIX RGB MATRIX IC1451(1/3) CLAMP R BUFF R IN Q1456 R AMP CLAMP CN2401 BUFF BUFF BUFF BUFF Q1451,1452 Q1453 R OUT R OUT Q2401 Q2402,2404 Q2405 Q2406-2408 Q2409 IC1453(1/3) IC1452(1/2)
Q (2/2), B (4/5, 5/5), M, T (2/2), H1 (14L)/HA (20L), H2 (14L)/HB (20L) Q (2/2), B (4/5, 5/5), M, T (2/2), H1 (14L)/HA (20L), H2 (14L)/HB (20L) (CPU) (2/2) (2/2) (4/5) IC1101 IC3770 CN1102 (RS485 DRIVER) (OSD) SHIFT LINE A/S CN1901 CN302 CN108...
Page 135
(SIGNAL SELECT) IC805 BYPASS SW IC803 IC806 DL801 CN801 DL803 CN3801 BUFF DL802 BUFF BUFF BUFF Y AMP Y GAIN VIDEO/Y BUFF Y AMP Q801 Q818 Q820,821 Q822 Q823 Q815 Q816,817 R-Y/R B BOARD B BOARD CN301 B-Y/B CN201 BUFF BUFF MUTE FL801...
Page 136
C, D, D1, D2, DY C, D, D1, D2, DY (H/V SYNC) IC1503(1/2) IC1503(2/2) IC1505 H SYNC CN2504 CN2507 CN1502(1/2) H SYNC H/V JUNGLE IC1504 CN1502(2/2) H SYNC H SYNC H SYNC Q2 10 H IN H FOCUS V SYNC V SYNC V SYNC V IN...
Page 137
G, J G, J T602 D613 +180V RECT IC601 D619 POWER FACTOR CONT RECT +15V CATHODE IC604 O.C.P D608 D614 Q608 +12V RECT +12V AC SENSE ( FBT/REG) D616 DRA IN L SENSE IC606 LATCH RECT Q611,612 CN601 CN602 CN951 CN951 CN602 OP +5V...
Page 139
Section 9 Diagrams Note: [Measuring conditions, voltage and waveform] ..Parts marked “ * ” differ according to the model/destination. Refer ..A voltage value is the reference value between the measurement to the mount table for each function.
Page 147
B (3/5) CXA1211M (IC252, IC1301, IC1401) B (3/5) M62399FP (IC3, IC4) B (2/5) (3/5) MB88141APF (IC1) CS0 CS1 CS2 VREFU2 IN 2 CONT 2 OUT 2 8-BIT 8-BIT (R-2R) LATCH VCA 2 CHIP SELECT D/A CONV. VCA 1 8-BIT 8-BIT 8BIT 8BIT 8BIT...
Page 148
B (4/5) MC74HC157AFEL (IC53, 54) B (4/5) TC4W53FU (IC55) B (5/5) TC7S32FU (IC2045) IN B IN A OUT Y B (5/5) TC74VHC14FT (IC2043) B (5/5) TC7W74FU (IC1055) B (5/5) MC74HC4538AFEL (IC2042, IC2046) 2-CR 2-RD 2-CK 2-CR B (1/5) TC74VHCT244AF (IC102, IC103) B (4/5) Z8622812PSC (IC51) (DIGITAL) (ANALOG)
Page 155
C 1 5 1 R 2 4 0 6 C 1 4 2 C 2 4 0 6 R 2 4 0 7 R 1 2 3 C 1 1 8 D 1 0 2 D 2 4 0 1 R 1 3 1 C 2 4 1 2 C 1 4 3...
Page 156
B1 (1/2) BA7046F (IC2801, IC2806) B1 (1/2) CXD2309Q (IC802) B1 (2/2) M51279FP-ETP (IC2804) PHASE PHASE (LSB) R0 H. OSC H. OSC 4LSB’S COMP COMP CURRENT CELLS R – Y B – Y ID KILLER SYNC SEP COMP COMP 6LSB’S LATCHES CURRENT SYNC DECODER...
Page 157
B1 (1/2), (2/2) MB88141APF (IC2805, IC4803) B1 (2/2) TDA4665T (IC3802) DIGITAL SUPPLY (R-Y)IN – 8-BIT 8-BIT (R-2R) LATCH D/A CONV. SIGNAL CLAMPING SAMPLE LINE AND- 8-BIT MEMORY DGND (B-Y)IN 8-BIT HOLD – (R-2R) LATCH pre-amplifiers addition output D/A CONV. stages buffers IIC BUS INTERFACE...
Page 165
For 14 inch models CN5001 C5001 C5002 0.01 F:CHIP B:CHIP LED POWER Q5001 Q5002 Q5003 Q5004 Q5005 Q5006 Q5007 Q5008 Q5009 Q5010 Q5011 Q5012 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 G BOARD LED DRIVE LED DRIVE R5008 LED DRIVE...
Page 166
HA, HB HA, HB For 20 inch models HA BOARD *:B SIDE R2944 S2909 S2907 S2905 S2903 S2901 S2910 S2908 S2906 S2904 S2902 S2915 S2914 S2913 S2912 S2911 R2925 D2901 R2907 R2913 R2943 R2924 R2918 R2912 R2923 R2917 R2933 R2928 R2953 R2949 R2934...
Page 167
For 20 inch models C2901 C2902 0.01 Q2905 Q2903 Q2904 Q2901 Q2902 F:CHIP B:CHIP IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 LED DRIVE LED DRIVE LED DRIVE LED SRIVE LED DRIVE R2953 R2909 R2923 R2933 R2943 R2917 R2928 R2938 R2949 :CHIP R2903 :CHIP :CHIP :CHIP...
Page 168
For 20 inch models CN5001 C5002 F:CHIP LED POWER Q5006 Q5007 Q5009 Q5012 Q5001 Q5002 Q5003 Q5004 Q5005 Q5008 Q5010 Q5011 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 IMZ4 LED DRIVE LED DRIVE LED DRIVE LED DRIVE LED DRIVE R5004 LED DRIVE...
Page 183
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : Check the metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to...
Need help?
Do you have a question about the TRINITRON PVM-14L5 and is the answer not in the manual?
Questions and answers