JVC KD-AV7100 Installation & Connection Manual
Hide thumbs
Also See for KD-AV7100:
- Instructions manual (111 pages) ,
- Installation & connection manual (6 pages) ,
- Installation & connection manual (6 pages)
Advertisement
Quick Links
KD-AV7100
Installation/Connection Manual
LVT1824-006D
[A]
This unit is designed to operate on 12 V DC, NEGATIVE
ground electrical systems. If your vehicle does not have
this system, a voltage inverter is required, which can be
purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location
where;
– it may obstruct the steering wheel and gearshift lever
operations, as this may result in a traffic accident.
– it may obstruct the operation of safety devices such as air
bags, as this may result in a fatal accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the
steering wheel, as this may result in a traffic accident.
• The driver must not watch the monitor while driving. It
may lead to carelessness and cause an accident.
• If you need to operate the unit while driving, be sure to
look around carefully or you may be involved in a traffic
accident.
• If the parking brake is not engaged, the following warning
appears on the monitor, and no playback picture will be
shown.
CAUTION!!!
IT'S UNLAWFUL TO OPERATE A VEHICLE WHILE
VIDEO IS DISPLAYED IN THE DRIVERS VIEWING
AREA
ENGAGE EMERGENCY BRAKE TO ENJOY VIDEO
– This warning appears only when the parking brake lead
is connected to the parking brake system built in the car.
Notes on electrical connections:
Replace the fuse with one of the specified rating. If the
•
fuse blows frequently, consult your JVC car audio dealer.
It is recommended to connect speakers with a maximum
•
power of more than 50 W (both at the rear and at the
front, with an impedance of 4 Ω to 8 Ω).
To prevent short circuits, cover the terminals of the
•
UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
Heat sink
TROUBLESHOOTING
• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in
common?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in
common?
• This unit does not work at all.
* Have you reset your unit?
Parts list for installation and connection
The following parts are provided for this unit. If anything is missing, contact your dealer immediately.
a
Main unit
d
Power cord
g
h
Round head screw
Round head screw
(M5 x 5 mm)
(M4 x 2.5 mm)
l
m
Handles
Stay
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to your
specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer
or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Do the required electrical
connections.
c
Removing the unit
Before removing the unit, release the rear section.
c
1
b
Sleeve
e
Parking brake lead
i
j
Tapping screw
Mounting bolt
n
o
Cleaning cloth
Remote controller
k
j
Insert the two handles, then pull them as illustrated so
that the unit can be removed.
0508MNMMDWSKP
©2008 Victor Company of Japan, Limited
c
Trim plate
f
Special cable for iPod
k
Rubber cushion
When shipped from the factory,
the battery is installed in the
remote controller.
b
Bend the appropriate tabs to
hold the sleeve firmly in place.
l
EN
Advertisement
Related Manuals for JVC KD-AV7100
Summary of Contents for JVC KD-AV7100
- Page 1 The following illustration shows a typical installation. However, you should make adjustments corresponding to your UNUSED leads with insulating tape. specific car. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer • The heat sink becomes very hot after use. Be careful not to or a company supplying kits.
- Page 2 Install the unit at an angle of less than 30˚, taking it into When using the stay account that the monitor would eject when in use (see below). Fire wall Washer Dashboard Lock nut Required space for the monitor ejection Unit: mm Bend the supplied stay.
- Page 3 Right speaker (front) Left speaker (rear) Right speaker (rear) Connecting the parking brake lead Connect the parking brake lead to the parking brake system built in the car. KD-AV7100 Parking brake lead (supplied) PARKING Crimp connector (not supplied) Parking brake...
- Page 4 • After you have connected the center speaker, make sure to activate the center speaker; otherwise, no sound comes out of the connected center speaker, see page 43 of the INSTRUCTIONS. • Disconnect the speakers from the unit, and connect them to the amplifier. Leave the speaker leads of the unit unused. Front speakers Center speaker JVC Amplifier JVC Amplifier KD-AV7100 Subwoofer Rear speakers...
Need help?
Do you have a question about the KD-AV7100 and is the answer not in the manual?
Questions and answers