All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by JH 0666 BG CD Customer Service...
EN 2 EBJ1.0U Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Technical Specifications 51 inch model : 75 kg (165 lbs) 60 inch model : 84 kg (185 lbs) 1.1.1 Reception Connections Tuning System : PLL Nr.
Page 3
Technical Specifications, Connections, and Chassis Overview EBJ1.0U EN 3 HDMI: Digital Video, Digital Audio - In 1.2.2 Side AV Panel E_06532_017.eps 250505 Figure 1-2 HDMI (type A) connector - D2+ Data channel - Shield - D2- Data channel - D1+...
EN 4 EBJ1.0U Safety Instructions, Warnings, and Notes 2. Safety Instructions, Warnings, and Notes Index of this chapter: 1. Perform the “general repair instruction” noted above. 2.1 Safety Instructions 2. Clean the power supply and deflection circuitry on the 2.2 Maintenance Instructions chassis.
Page 5
Lead-free Solder indication on these semiconductors. • Manufactured under license from Dolby Laboratories. Philips CE is producing lead-free sets (PBF) from 1.1.2005 “Dolby”, “Pro Logic” and the “double-D symbol”, are onwards. trademarks of Dolby Laboratories. Identification: The bottom line of a type plate gives a 14-digit 2.4.2...
Page 6
2.4.5 Alternative BOM identification In September 2003, Philips CE introduced a change in the way the serial number (or production number, see Figure 2-2) is composed. From this date on, the third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative BOM (Bill of Materials used for producing the specific model of TV set).
Directions for Use EBJ1.0U EN 7 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 8 EBJ1.0U Mechanical Instructions 4. Mechanical Instructions Index of this chapter: 1. Disassembly Procedures 2. Service Position 3. Picture Tube Replacement 4. Re-assembly Notes: • Figures below can deviate slightly from the actual situation, due to the different set executions.
Page 9
Mechanical Instructions EBJ1.0U EN 9 G_15860_061.eps G_15860_064.eps 100406 100406 Figure 4-4 Lower front cover 2/3 Figure 4-6 CBA carrier frame 4.1.6 Large Signal Board Removal (LSB) 1. Remove lower centre back cover. 2. Disconnect all cables from the LSB. 3. Remove all fixation screws [1] from the LSB and pull the tabs [2] on the right hand side of the LSB.
Page 10
EN 10 EBJ1.0U Mechanical Instructions 4.1.7 Medium Signal Board Removal (MSB) 1. Remove lower centre back cover. 2. Disconnect all cables from the MSB. 3. Remove all fixation screws [1] from the MSB and pull the tab [2] on the right hand side of the MSB.
Page 11
Mechanical Instructions EBJ1.0U EN 11 4.1.10 Side I/O Panel Removal 1. Remove the Left Side Back Cover (see procedure above). 2. Disconnect the connectors [1] from the panel. 3. Remove two screws [2] from the panel. 4. Slide the Side I/O Panel CBA out of the bracket.
Page 12
EN 12 EBJ1.0U Mechanical Instructions Note: Take care not to place fingerprints or smudges on the mirror. G_15860_074.eps 100406 Figure 4-17 Small signal board 3/3 G_15860_077.eps 4.1.12 Left or Right Speaker Removal 100406 Figure 4-20 Mirror 1. Remove the Left or Right Side Back Cover.
Page 13
Mechanical Instructions EBJ1.0U EN 13 spillage. The technician must carefully reassemble the CRT/ 6. With an awl or marking pen, outline the edges of the CRT optical components, ensuring a proper seal of the coupling onto the coupler. fluid. Use only factory original coupling fluid.
Page 14
EN 14 EBJ1.0U Mechanical Instructions F. Replacing the PTV Coupling Fluid Notes: • Before replacing the CRT coupling fluid, ensure the expansion chamber bladder is fully collapsed. This can be easily inspected by viewing the bladder through the small hole on the expansion chamber assembly. If the rubber of...
Service Modes, Error Codes, and Fault Finding EBJ1.0U EN 15 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • All sound settings at 50%, except volume at 25%. 5.1 Test Points • All service-unfriendly modes (if present) are disabled, like: 5.2 Service Modes...
Page 16
EN 16 EBJ1.0U Service Modes, Error Codes, and Fault Finding How to Navigate When you press the “MENU” button on the RC transmitter, the set will toggle between the SDM and the normal user menu (with the SDM mode still active in the background).
Page 17
Service Modes, Error Codes, and Fault Finding EBJ1.0U EN 17 HARDWARE INFO OPERATION HOURS ERRORS DEFECTIVE MODULE RESET ERROR BUFFER GENERAL WHITEPOINT ALIGNMENTS PERSONAL OPTIONS DEALER OPTIONS COLOR TEMPERATURE NORMAL/WARM/COOL PICTURE MUTE OFF/ON WHITEPOINT RED VIRGIN MODE OFF/ON WHITEPOINT GREEN 2CS KOREA N.A.
Page 18
EN 18 EBJ1.0U Service Modes, Error Codes, and Fault Finding Contents of SAM: If the NVM was corrupted or empty before this action, it will be • Hardware Info. initialised first (loaded with default values). This initialising can – A. VIPER SW Version. Displays the software version take up to 20 seconds.
Page 19
Service Modes, Error Codes, and Fault Finding EBJ1.0U EN 19 – (De) activate the selected submenu. • Dolby. Indicates whether the received transmitter transmits Dolby sound (“ON”) or not (“OFF”). Attention: The presence of Dolby can only be tested by the software on How to Exit SAM the Dolby Signaling bit.
UART SERVICE CONNECTOR CONNECTOR Service Tools 5.3.1 ComPair Introduction ComPair (Computer Aided Repair) is a service tool for Philips I 2 C Power Consumer Electronics products. ComPair is a further 9V DC development on the European DST (service remote control), E_06532_021.eps 180804 which allows faster and more accurate diagnostics.
Page 21
Service Modes, Error Codes, and Fault Finding EBJ1.0U EN 21 Basically there are three kinds of errors: 5.4.3 How to Clear the Error Buffer • Errors detected by the Stand-by Processor. These errors will always lead to protection and an automatic start...
Page 22
EN 22 EBJ1.0U Service Modes, Error Codes, and Fault Finding Error Description Monitored by Error/Prot Device Defective Module schematics ID PIC ambient light controller EPLD 16F818 ambient_light PIC ambient light controller EPLD 16F818 ambient_light DVD engine disc systems Viper t.b.d.
Page 23
Service Modes, Error Codes, and Fault Finding EBJ1.0U EN 23 Extra Info NVM gives no acknowledge, the stand-by software • Error 1 (I C bus 1 blocked). When this error occurs, the assumes that the bus is blocked, the TV goes to protection TV will go to protection and the front LED will blink at 3 Hz.
Page 24
EN 24 EBJ1.0U Service Modes, Error Codes, and Fault Finding Protections Fault Finding and Repair Tips 5.6.1 Software Protections Read also paragraph "Error Codes" - "Extra Info". Most of the protections and errors use either the stand-by 5.7.1 Exit “Factory Mode”...
2U09, 2U10, 2U23 and (e.g. USB memory stick). You can download the new software 2U73, and IC 7U00. from the Philips website to your PC. Note 1: If fuse 1U01 is broken, this usually means a pair of Partition 0 (Service) defective power MOSFETs (7U01 or 7U03).
Page 26
TV into the software upgrade application. To do so: • Disconnect the TV from the Mains/AC Power. • Press the “OK” button on a Philips DVD RC-6 remote control (it is also possible to use the TV remote in "DVD" mode when available). •...
Block Diagrams, Test Point Overviews, and Waveforms EBJ1.0U 6. Block Diagrams, Test Point Overviews, and Waveforms Wiring Diagram WIRING 1517 CONV DEFL YOKE YOKE -35V -22V FOCUS -22V TO 1201 FOCUS RED CRT PANEL +35V FOCUS 1M02 CONV DEFL +5V2...
Block Diagrams, Test Point Overviews, and Waveforms EBJ1.0U Block Diagram Video VIDEO MAIN TUNER MPIF MAIN: VIPER: VIPER: MAIN MEMORY PNX 2015: 7A00 7J00 PNX3000HL 7V00 7V01 PNX2015E PNX8552 K4D551638F TUNNELBUS 1T04 1A10 SUPPLY VIFINP TD1336/FGHP MAIN MEMORY SOUND GROUP...
Block Diagrams, Test Point Overviews, and Waveforms EBJ1.0U Block Diagram Control & Clock Signals CONTROL + CLOCK SIGNALS CHANNAL DECODER VIPER: PNX2015: VIDEO DAC 7V00 7G40 PNX8550EH/M1/S1 ADV7123KST140 A/V + TUNNELBUS DV-CLKIN DV-CLKIN VIDEO 7J00 PNX2015E VIPER DV I/O INTERFACE...
Circuit Diagrams and PWB Layouts EBJ1.0U SSB (.4 Version) UART SRP List Explanation Example 1.1. Introduction Net Name Diagram 1I10 D2 +12-15V AP1 (4x) UART +12-15V AP4 (4x) 1I11 C2 SRP (Service Reference Protocol) is a software tool that creates a list with all references to signal lines. The list contains...
Alignments EBJ1.0U EN 133 8. Alignments Index of this chapter: 5. Repeat steps two through four to adjust the focus of the two 8.1 General Alignment Conditions remaining CRTs. 8.2 Hardware Alignments 8.3 Software Alignments Note: Before beginning the following adjustment procedures, 8.4 Option Settings...
Page 134
EN 134 EBJ1.0U Alignments Software Alignments 1. Select a COLOUR TEMPERATURE (e.g. COOL, NORMAL, or WARM). 2. Set the RED, GREEN and BLUE default values according Put the set in SAM mode (see the "Service Modes, Error Codes to the values in the "Tint settings" table.
Not applicable in these sets Option numbers Group 1 “Value” 00016 0001x 00545 14979 (see set sticker) x=5: Magnavox 51”, x=6: Philips 51”, x=7: Philips 60” Group 2 “Value” 00034 00000 16928 00000 (see set sticker) Store To store changed option numbers...
Page 136
EN 136 EBJ1.0U Alignments 8.4.5 GDE SAM Specifications: • Set display mode in service mode. • Service blanking. • Set geometry. • Preset picture. • Set white tone. • Convergence disable for setting geometry. The GDE SAM mode (GDE = Generic Display Engine), allows the Service Technician to set Geometry and White Tone (Grey Scale).
Page 137
Alignments EBJ1.0U EN 137 Convergence and Geometry Adjustments Table 8-6 Geometry Default Values 1080i 8.5.1 Introduction Wide blank Horizontal Shift If the Medium Signal Board (MSB) has been replaced, the Horizontal Para following adjustments will be required in the order as shown: E-W Width 1.
Page 138
EN 138 EBJ1.0U Alignments CURSOR RIGHT MENU CURSOR KEYS TO ADJUST CURSOR KEYS TO NAVIGATE MENU TO CHANGE MENU TO ADJUST STEP SIZE I+ TO RETURN I+ TO RETURN GREEN RED TO GREEN BLUE TO GREEN GREEN TO RED BLUE TO RED...
Page 139
Alignments EBJ1.0U EN 139 8.5.7 Touch Up Convergence in the selection menu. Using the same method that was used to adjust the Green Grid to the Template, adjust the Red Grid onto the Green Grid. If the set is a later production, select SP When making minor Convergence corrections, move the RED to centre the Red grid onto the Green grid.
9.6 List of Abbreviations Aspect Ratio Model Chassis Destination 9.7 IC Data Sheets 16x9 51PP9200/37 EBJ1.0U RA 16x9 60PP9200/37 EBJ1.0U RA Introduction The EBJ1.0 chassis (= HDPTV2K6) mainly consists of the following three panels: This document is prepared for HDPTV2K6 maintenance 1.
Page 141
POD interface. However, the AVIP, MPIF, PNX, and VIPER part are comparable. The Eco Baby Jag (=EBJ) module is the same digital module developed by Philips for LCD and PDP with a difference General Overview (components fitted differently) in video interface for CRT RPTV (video interface: RGBHV (1366X1080i@60Hz) and communication port is UART).
Page 142
EN 142 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets approximately 6 volts DC. This circuit is protected by fuse 1806 • Hblank: LOT pin10, generated through 3802/6804. It is for and resistor 3801. horizontal retrace period blanking. It is feedback to HOP IC to blank the video during flyback.
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 143 voltage generator), coupled by the HVG capacitor and then Consequently, -200V will not be available and set shut down connected to the tube's focus electrode. with error 61. Misc. components: 9.3.5...
Page 144
EN 144 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets = [4.5m * 22K +2 * 0.7] + 1.87 * 22K / 820 * (Vpin4 - Vpin2) locks the horizontal output stage flyback phase to HOP Hfreq With the above equation, we know that we have a signal local oscillator.
Page 145
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 145 SCO is the sandcastle output from the HOP IC. The sandcastle List of Abbreviations pulse can be used as clamp and blanking reference for display generating devices like TXT decoders and PIP processors. The...
Page 146
Sound Intermediate frequency to form one frame. Each field contains Surround Left half the number of the total amount of SPDIF Sony Philips Digital Interface Format lines. The fields are written in "pairs", Small Signal Board causing line flicker. Small Signal Module...
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 147 IC Data Sheets This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the electrical diagrams (with the exception of "memory" and "logic"...
Page 148
EN 148 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.2 Diagram B2A, NXT2004 (IC 7T22) Block Diagram VSB/QAM MPEG IF In text text text Demodulator Transport Sense 32K x 8 text BERT text RF Gain SRAM text IF AGC RF AGC µC...
Page 149
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 149 9.7.3 Diagram B3A/B/C/D, PNX 3000H (IC 7A00) Block Diagram CVBSOUTA 1× CVBSOUTB 2NDSIFEXT (FMRAD) CVBSOUTIF SIFAGC MIXER SIFIN 2nd SIF internal & AM SND DEMOD DTV 1st IF DTVOUT...
Page 150
EN 150 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.4 Diagram B4A/B/C/D/E/F, PNX 2015 (IC 7J00) Block Diagram 16-BIT 225 MHz DDR PNX2015 MEMORY CONTROLLER video NORTH TUNNEL SOUTH TUNNEL PNX8550 coprocessor HD input (TDA9975) MEMORY VO-1 BASED SCALER...
Page 151
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 151 9.7.5 Diagram B5C, VIPER (IC 7V00) Block Diagram Streaming Interface Optional External 32-Bit 225 MHz DDR from Tunnel Video Improvement Processing PNX8550 Memory 30 (dig) DVD-CSS 5-Layer Controller Primary...
Page 152
EN 152 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.6 Diagram B5F, LD3985M33 (IC 7M05/6) Diagram B6, LD3985M33 (IC 7G42) Diagram B7A, LD3985M33 (IC 7B25) Block Diagram Pin Configuration TSOT23-5L/SOT23-5L Flip-Chip G_16290_084.eps 020206 Figure 9-9 Internal block diagram and pin configuration...
Page 153
Circuit Descriptions, Abbreviation List, and IC Data Sheets EBJ1.0U EN 153 9.7.7 Diagram B6, ADV7123KSTZ140 (IC 7G40) Block Diagram BLANK BLANK AND SYNC LOGIC SYNC DATA R9–R0 REGISTER DATA G9–G0 REGISTER DATA B9–B0 REGISTER VOLTAGE POWER-DOWN PSAVE REFERENCE MODE CIRCUIT...
Page 154
EN 154 EBJ1.0U Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.7.8 Diagram B7A, LD1117DT33 (IC 7B45) Block Diagram Pin Configuration LD1117DT DPAK F_15710_166.eps 230905 Figure 9-11 Internal block diagram and pin configuration 9.7.9 Diagram B8A, LM339P (IC 7D10) Block Diagram Pin Configuration G_16290_082.eps...
Revision List EBJ1.0U EN 165 11. Revision List Manual xxxx xxx xxxx.0 • First release. Manual xxxx xxx xxxx.1 • Chapter 7: SSB point 5 version added. • Chapter 10: Spare Parts List added.
Need help?
Do you have a question about the EBJ1.0U and is the answer not in the manual?
Questions and answers