Toro Sand Pro 3040 Manual
Drag mat carrier system
Hide thumbs
Also See for Sand Pro 3040:
- Service manual (262 pages) ,
- Operator's manual (44 pages) ,
- Installation instructions (4 pages)
Table of Contents
Advertisement
Quick Links
Drag Mat Carrier System
Sand Pro
Model No. 08756-Serial No. 260000001 and Up
This product contains a chemical or chemicals known to the State of California to
Introduction
Read this information carefully to learn how to operate and
maintain your product properly and to avoid injury and
product damage. You are responsible for operating the
product properly and safely.
You may contact Toro directly at www.Toro.com for product
and accessory information, help finding a dealer, or to register
your product.
Whenever you need service, genuine Toro parts, or additional
information, contact an Authorized Service Dealer or Toro
Customer Service and have the model and serial numbers of
your product ready. Figure 1 identifies the location of the
model and serial numbers on the product. Write the numbers
in the space provided.
1. Model and serial number location
© 2016-The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
/Infield Pro
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Figure 1
Register at www.Toro.com.
®
3040 and 5040 Traction Unit
WARNING
CALIFORNIA
Model No.
Serial No.
This manual identifies potential hazards and has safety
messages identified by the safety-alert symbol
which signals a hazard that may cause serious injury or death
if you do not follow the recommended precautions.
1. Safety-alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical information
and Note emphasizes general information worthy of special
attention.
Contents
Introduction .................................................................. 1
Safety ........................................................................... 3
Safety and Instructional Decals ................................. 3
Setup ............................................................................ 3
1 Assembling the Drag Mat Carrier ............................ 4
2 Installing a Mat ..................................................... 5
Unit ................................................................... 6
4 Adjusting the Link Assembly .................................. 7
Loose Parts......................................................... 7
Product Overview .......................................................... 8
Operation ..................................................................... 8
Restraining the Side-to-Side Pivot .............................. 8
Form No. 3406-765 Rev A
Installation Instructions
Figure 2
Original Instructions (EN)
All Rights Reserved *3406-765* A
Printed in the USA
(Figure
2),
Advertisement
Table of Contents
Related Manuals for Toro Sand Pro 3040
Summary of Contents for Toro Sand Pro 3040
-
Page 1: Table Of Contents
(Figure You may contact Toro directly at www.Toro.com for product which signals a hazard that may cause serious injury or death and accessory information, help finding a dealer, or to register if you do not follow the recommended precautions. - Page 2 Using the Drag Mat Carrier........9 Adjusting the Transport Position ....... 9 Removing the Drag-Mat-Carrier System ..... 9 Maintenance ..............10 Inspecting and Cleaning the Drag-Mat Carrier and Traction Unit .............10 Greasing the Attachment Adapter......10...
-
Page 3: Safety
Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-5517 1. Warning—do not touch the hot surface. Installation Loose Parts Use the chart below to verify that all parts have been shipped. -
Page 4: Assembling The Drag Mat Carrier
Procedure Description Qty. Operator’s Manual Parts Catalog Read the documentation and store the Clevis pin loose parts. Washer (0.469 x 0.922 inch) Hairpin cotter Assembling the Drag Mat Carrier Parts needed for this procedure: Drag-mat-carrier assembly Attachment-adapter assembly Shoulder bolt Washer (0.531 x 1.063 inch) Washer (0.469 x 0.922 inch) Locknut (7/16 inch) -
Page 5: Installing A Mat
Installing a Mat Parts needed for this procedure: Steel mat (not included in this kit, order separately) Coconut-fiber mat (not included in this kit, order separately) Mat retainer Bolt (3/8 x 1 inch) Flange nut (3/8 inch) Figure 4 Procedure 1. -
Page 6: Mounting The Drag Mat Carrier To The Traction Unit
2. If you are installing the coconut-fiber mat, drill a hole (3/8 inch) in the mat at each clamp location, using the mat retainer as a template (Figure Figure 8 1. Drag-mat carrier side 3. Bolt 2. Skid 4. Nut Figure 7 1. -
Page 7: Adjusting The Link Assembly
2. If the gap is not correct, loosen the jam nut and tighten or loosen the adjustment nut on the link assembly as needed to change the gap (Figure 10). Reading the Documentation and Storing the Loose Parts Parts needed for this procedure: Figure 9 Operator’s Manual 1. -
Page 8: Product Overview
Product Overview Figure 11 1. Attachment adapter 4. Drag-mat carrier 2. Locking lever 5. Mat retainer 3. Lift arm 6. Drag mat Operation Restraining the Side-to-Side Pivot As installed, the drag-mat carrier pivots side to side when you turn corners to better follow the traction unit and protect the edges of the drag mat. - Page 9 Removing the you will not need it. The excess skidding of the drag mat can cause cosmetic damage to the edges. Drag-Mat-Carrier System 1. Pivot the locking lever to the left (Figure 14). Using the Drag Mat Carrier 2. Lower the traction-unit adapter. The drag-mat carrier is designed to have the traction unit 3.
- Page 10 Maintenance Inspecting and Cleaning the Drag-Mat Carrier and Traction Unit When you finish operating the machine, clean the it thoroughly. Wash off the machine after each use. If you clean the machine frequently (before the material has a chance to cake), you can clean it with a stream of water from a hose with the nozzle removed.
- Page 11 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.
Need help?
Do you have a question about the Sand Pro 3040 and is the answer not in the manual?
Questions and answers