PART NAMES AND FUNCTIONS Indoor Unit Auto Air Swing Vane Guide vane Disperses airflow up and down and adjusts the angle Air flow can be changed to horizontal of airflow direction. by moving the guide vane to the left or right. Horizontal Air Outlet Filters Air intake...
Page 4
Wired remote controller Display Section Day-of-Week “Sensor” indication For purposes of this explanation, Displayed when the remote controller Shows the current day of the week. all parts of the display are shown sensor is used. as lit. During actual operation, only the relevant items will be lit.
MICROPROCESSOR CONTROL INDOOR UNIT CONTROL 8-1. COOL OPERATION <How to operate> 1 Press POWER ON/OFF button. TIME SUN MON TUE WED THU FRI SAT TIMER AFTER AFTER 2 Press the operation MODE button to display COOL. ERROR CODE FUNCTION ˚F˚C FILTER ˚F˚C 3 Press the TEMP.
Page 14
From the preceding page Control modes Remarks Control details 3. Drain pump 3-1. Drain pump control • Always drain pump ON during the COOL and DRY mode operation. (Regardless of the thermostat ON/ OFF) • When the operation mode is changed from COOL or DRY to any other mode (including Stop), the drain pump continues to run for 3 minutes.
8-2. DRY OPERATION <How to operate> 1 Press POWER ON/OFF button. TIME SUN MON TUE WED THU FRI SAT TIMER AFTER AFTER 2 Press the operation MODE button to display DRY. ERROR CODE FUNCTION ˚F˚C FILTER ˚F˚C 3 Press the TEMP. button to set the desired temperature. WEEKLY SIMPLE ONLY1Hr.
8-3. FAN OPERATION <How to operate> 1 Press POWER ON/OFF button. TIME SUN MON TUE WED THU FRI SAT 2 Press the operation MODE button to display FAN. TIMER AFTER AFTER ERROR CODE FUNCTION ˚F˚C FILTER ˚F˚C WEEKLY SIMPLE ONLY1Hr. AUTO OFF TEMP.
8-4. HEAT OPERATION <How to operate> 1 Press POWER ON/OFF button. 2 Press the operation MODE button to display HEAT. TIME SUN MON TUE WED THU FRI SAT 3 Press the TEMP. button to set the desired temperature. TIMER AFTER AFTER ERROR CODE FUNCTION...
Page 18
From the preceding page Control modes Control details Remarks 2-3. Thermo OFF mode 2. Fan When the thermoregulating function changes to OFF, the indoor fan operates in [Extra low]. 2-4. Heat defrosting mode The indoor fan stops. 3. Drain pump No drain pump operation However, when the control changes from COOL or DRY operation, the drain pump operates for 3 minutes.
Page 19
8-5. AUTO OPERATION [AUTOMATIC COOL/HEAT CHANGE OVER OPERATION] <How to operate> 1 Press POWER ON/OFF button. TIME SUN MON TUE WED THU FRI SAT 2 Press the operation MODE button to display AUTO. TIMER AFTER AFTER ERROR CODE FUNCTION 3 Press the TEMP. button to set the desired temperature. ˚F˚C FILTER ˚F˚C...
TROUBLE SHOOTING 9-1. HOW TO CHECK THE PARTS PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Parts name Check points Thermistor (TH21) Disconnect the connector then measure the resistance with a tester. <Room temperature (At the ambient temperature 50 F~86 F) detection>...
<Thermistor characteristic graph> < Thermistor for lower temperature > Thermistor <Room temperature detection> (TH21) Thermistor for Thermistor <Liquid pipe temperature detection> (TH22) lower temperature Thermistor <Gas pipe temperature detection> (TH23) Thermistor R =15k' ± 3% Fixed number of B=3480K ± 2% Rt=15exp { 3480( 273+(t-32)/1.8 30_F...
Page 22
<Output pulse signal and the valve operation> Output Output (Phase) Closing a valve : 1 Opening a valve : 4 The output pulse shifts in above order. • When linear expansion valve operation stops, all output phase become OFF. • At phase interruption or when phase does not shift in order, motor 2 2 Linear expansion valve operation does not rotate smoothly and motor will lock and vibrate.
Page 23
9-2. TROUBLESHOOTING Check method of indoor fan motor (fan motor / controller board) Notes · High voltage is applied to the connecter (FAN) for the fan motor. Give attention to the service. · Do not pull out the connector (FAN) for the motor with the power supply on, doing so may result in damage to the board. Self check Conditions : The indoor fan does not rotate.
DISASSEMBLY PROCEDURE PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Be careful when removing heavy parts. OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS Photo 1 1. Removing the intake grille Opening the air intake grille (1) Press the of the air intake grille.(See figure 1)
Page 28
OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS Photo 2 2. Removing the electrical parts box Claw in middle Nozzle Electrical parts of nozzle (1) Remove the panel. (2) Remove the address board cover. (3) Remove the electrical parts cover. (4) Disconnect the connectors of fan motor, vane motor, drain pump, room temperature thermistor, pipe temperature thermistor,...
Page 29
OPERATING PROCEDURE PHOTOS&ILLUSTRATIONS Photo 6 Drain sensor Drain pump 5. Removing the drain pump (1) Remove the panel. (2) Unhook the claw in the middle of nozzle and remove the drain pan. (3) Remove the address board cover. (4) Remove the electrical parts cover. (5) Disconnect the connector of drain pump.
PARTS LIST (non-RoHS compliant) PANEL PARTS FOR PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMP-16BMU Q'ty/set Wiring Recom- Remarks Part No. Diagram mended Part Name Specification (Drawing No.) Symbol Q'ty PMP-16BMU T7W E11 003 AIR OUTLET GRILLE LATCH PANEL HOOK GRILLE CATCH L.L.FILTER L.L.FILTER...
Page 31
FUNCTIONAL PARTS PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Part number that is circled is not shown in the figure. Q'ty/set Wiring Recom- Remarks Part No. Part Name Specification PMFY-P · NBMU-E Diagram mended (Drawing No.) Symbol Q'ty 06/ 08 12/ 15 BEARING MOUNT...
Page 32
ELECTRICAL PARTS PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Q'ty/set Wiring Recom- Remarks PMFY-P Part No. Part Name Specification Diagram mended (Drawing No.) 06/08/12/15 Symbol Q'ty NBMU-E T7W E11 716 3P (L1,L2,G) TERMINAL BLOCK T7W E17 716 3P (M1,M2,S) TERMINAL BLOCK TB15 2P(1,2)
RoHS PARTS LIST PANEL PARTS FOR PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMP-16BMU Q'ty/set Wiring Recom- Remarks Diagram mended Part No. Part Name Specification (Drawing No.) Symbol Q'ty PMP-16BMU T7W E16 003 AIR OUTLET GRILLE LATCH PANEL HOOK GRILLE CATCH L.L.FILTER...
Page 34
FUNCTIONAL PARTS PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Part number that is circled is not shown in the figure. Q'ty/set Wiring Recom- Remarks PMFY- Part No. Part Name Specification Diagram mended (Drawing No.) P·NBMU-E P·NBMU-E Symbol Q'ty 06/08 12/15...
Page 35
ELECTRICAL PARTS PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E PMFY-P06NBMU-E PMFY-P08NBMU-E PMFY-P12NBMU-E PMFY-P15NBMU-E Q'ty/set Wiring Recom- Remarks Part No. Part Name Specification PMFY-P06/08/12/15 Diagram mended (Drawing No.) Symbol Q'ty NBMU-E NBMU-E 3P (L1,L2,G) T7W E41 716 TERMINAL BLOCK R01 E27 246 3P (M1,M2,S)
Page 36
HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO100-8310, JAPAN cCopyright 2005 MITSUBISHI ELECTRIC ENGINEERING CO., LTD. Distributed in Jul. 2007. No. OC341 REVISED EDITION-B PDF 9 Distributed in Aug. 2006. No. OC341 REVISED EDITION-A PDF 9 Distributed in Jun. 2005. No. OC341 PDF 10 New publication, effective Jul.
Need help?
Do you have a question about the City Multi PMFY-P06NBMU-E and is the answer not in the manual?
Questions and answers